Rohde & Schwarz GmbH & Co. KG
Rohde & Schwarz is striving for a safer and connected world with its Test & Measurement, Technology Systems and Networks & Cybersecurity Divisions. The company’s leading-edge products and solutions empower industrial, regulatory and government customers to attain technological and digital sovereignty. The privately owned, Munich based company can act independently, long-term and sustainably.
- 1-888-837-8772
- Info@rsa.rohde-schwarz.com
- 6821 Benjamin Franklin Drive
Columbia,, MD 21046
United States of America
-
product
RF & Microwave Power Meters
Our RF & microwave power sensors ensure precise and reliable measurements. They provide the highest measurement accuracy and speed, simple operation, technological leadership in thermal, diode and OTA core measurement elements as well as traceability to national standards.
-
product
Conformance Test System
TS-RRM
The R&S®TS-RRM 5G and LTE test system is a test solution for running 5G NR and LTE inter-RAT RRM test cases for certification of wireless devices.It is a fully automated conformance test system for running validated RRM conformance test cases. In addition to the RRM test cases required by GCF/PTCRB, the R&S®TS-RRM also supports carrier acceptance specific RRM tests.
-
product
Vector Network Analyzer
ZVA
The R&S®ZVA110 provides a frequency range from 10 MHz to 110 GHz. It is based upon the R&S®ZVA67 4-port VNA, and includes all system components for seamless continuous sweep (models 03 and 13)
-
product
NRPxxA/AN
In EMC applications, usually only the average power is of interest. This is where the R&S®NRPxxA/AN average power sensors are the perfect fit. They cover measurement ranges that are used in radio telecommunications as well as the important lower frequency bands down to 8 kHz
-
product
Oscilloscope
RTB2000
Power of ten (10-bit ADC, 10 Msample memory and 10.1" touchscreen) combined with smart operating concepts make the R&S®RTB2000 oscilloscopes the perfect tool for university laboratories, for troubleshooting embedded designs during development and for production and service departments.
-
product
Communications Manufacturing Test Set
CMW100
The R&S®CMW100 communications manufacturing test set is based on the R&S®CMW platform. The flexible RF interface permits simultaneous testing of up to eight devices. The R&S®CMW100 remote control and measurement concepts are compatible with the R&S®CMW500. The R&S®CMW100 is optimized for cost-effective calibration and verification of wireless devices in non-signaling mode (analyzer/generator). The tester provides a new eco-friendly hardware concept, featuring extremely low energy consumption and a very compact size, making it ideal for use in fully automated robotic production lines. It supports LTE, 5G NR, WLAN, Bluetooth® and IoT technologies, making it ready for today and tomorrow.
-
product
Cellular Network Analysis Software
NESTOR
R&S®NESTOR is a Windows 10 based platform for analyzing cellular networks via the air interface. It is deployed by law enforcement agencies, intelligence services, armed forces and regulatory authorities. R&S®NESTOR is used together with R&S®TSMX mobile network scanners and QualiPoc smartphones, which offer the most advanced technology worldwide. The software supports all relevant applications that public authorities and security organizations need to gather information about cellular networks. R&S®NESTOR is used in vehicles, trains, aircraft, drones, on ships and on foot.
-
product
Vecor Signal Generator
SMM100A
The R&S®SMM100A vector signal generator provides remarkably good RF characteristics across the entire frequency range from 100 kHz to 44 GHz. The instrument covers the bands below 6 GHz used by existing wirelessstandards as well as the newly defined bands for 5G NR FR1 and Wi-Fi 6E up to 7.125 GHz and the 5G NR FR2 bands up to 44 GHz.The internal baseband generator in the R&S®SMM100A supports a maximum RF modulation bandwidth of 1 GHz. Digitally modulated broadband signals can thus be generated as required by the prevalent wireless standards. The R&S®SMM100A is well prepared for future bandwidth requirements.
-
product
Voice Communications Systems
NAVICS
The NAVICS® fully IP based ICS from Rohde & Schwarz uses a uniform IP network to connect distributed on-board voice terminals and other subsystems for internal and external communications. The ruggedized, highly available IT technology with creditable security is also from Rohde & Schwarz
-
product
Test Receiver
FSWT
The R&S®FSWT is the right tool for detecting compromising emanations. With two equivalent, switchable RF inputs, up to 500 MHz measurement and analysis bandwidth and two analog outputs for video voltage and demodulators, the R&S®FSWT fits perfectly into typical test setups and easily replaces older instruments.
-
product
Broadband Amplifier
BBL200
The R&S®BBL200 broadband amplifiers are ideal for applications requiring high RF power.
-
product
External Frontend
FE50DTR
The R&S®FE50DTR external frontend can extend the frequency range up to 50 GHz for Rohde&Schwarz signal and spectrum analyzers as well as signal generators. The R&S®FE50DTR enables signal up and downconversion directly at the device under test (DUT), lowering cable losses, increasing sensitivity and delivering more power at the antenna in an OTA environment. With a dual connector system, testing of active components is an easy task.
-
product
CATR Benchtop Antenna Test System
ATS800B
Very compact far-field over-the-air (OTA) test system based on compact antenna test range (CATR) technologyUnrivaled quiet zone size within 0.8 m2 footprintState-of-the-art reflector ensuring a high quiet zone accuracyUnique benchtop CATR system supporting over 50 GHzIndirect far-field method (approved by 3GPP for 5G OTA testing)
-
product
Power Analyzer
HMC8015
The R&S®HMC8015 Power analyzer is a compact tester for AC/DC load and standby current characterization that enables measurements without additional tools such as a computer or remote infrastructure. In addition to a numerical and graphical display with 26 key parameters, the instrument delivers performance and compliance protocols in line with IEC 62301, EN 50564 and EN 61000-3-2.
-
product
Test Software
Elektra
The R&S®ELEKTRA test software controls complete EMC systems and automates measurements of equipment under test (EUT) being certified for emissions (EMI) and immunity (EMS). R&S®ELEKTRA simplifies configuration of test systems and test descriptions in accordance with common standards. It speeds up test execution and paves the way to quickly generating a comprehensive test report.