Pulsar Microwave Corporation
Pulsar Microwave Corporation, established in 1987, is a U.S.-based manufacturer specializing in high-performance RF and microwave passive components spanning DC to 85 GHz. With full in-house design and manufacturing capabilities, we maintain strict control over quality, performance, and lead times, making us a trusted partner for both standard and custom-engineered solutions.
- 973-779-6262
- 973-779-2727
- sales@pulsarmicrowave.com
- 48 Industrial West
Clifton, NJ 07012
United States of America
Categories
-
product
Voltage Controlled Linearized Attenuators To 16 GHz
Pulsar's voltage controlled, PIN diode linearized attenuators are available from 0.25-16 GHz with attenuation ranges of 32 and 64 dB. Each model includes an integrated linearizer, and a driver that controls the attenuation level. This design results in transient free switching between attenuation levels as opposed to the spurious outputs that result when an attenuation value is switched either on or off by a direct digitally controlled attenuator. Transfer function is 8 dB / Volt.
-
product
4-Way High Power Combiners To 2200 MHz
Pulsar Microwave's high power 4-way combiners cover 5 MHz to 2.2 GHz and handle combined power of 25 to 400 watts. These combiners can combine non-coherent signals unconditionally. They are designed for use in 50-ohm systems, and come standard with SMA or N female connectors.
-
product
Digital Controlled Phase Shifters To 4 GHz
Pulsar's Digital Controlled Phase shifters utilize PIN diodes and delay lines to produce the necessary phase requirements. These digital phase shifters use switched lines to obtain temperature stable phase shift. The phase is specified at the center frequency ± 3.0% and is proportional to frequency over the entire band.
-
product
Triple Balanced Mixers From 0.05 To 4200 MHz
A triple balanced mixer uses two well matched quad-diode rings. Because of this, they offer wider LO/RF bandwidths than DBM designs. But more importantly, the TBM offers a higher dynamic range and lower distortion.
-
product
SP3T RF Pin Diode Switches To 18 GHz
Pulsar Microwave manufactures 3-way absorptive and reflective switches for use in 50-ohm systems. These SP3T switches operate from 100 MHz to 18 GHz and handle 200 mW input power. VSWR performance is often 1.6:1 or better with 100 ns switching time. Minimum isolation of 60 dB is specified for most units. Absorptive and reflective switches require +5V and -5V power supply to function. Control logic is from 0 to +5 volts. All voltage and ground connections are made by feed thru and turret terminals, respectively.
-
product
Frequency Doublers To 12 GHz
Pulsar Microwave Frequency Doublers utilize Schottky diodes in a bridge configuration to accomplish the frequency doubling. The input frequency operates from 0.2 to 6000 MHz. Frequency Quadruplers are also available using using this topology. Designs are matched to 50 Ohms and are available in a wide variety of package styles, such as plug-in, flatpack, and connectorized housings. Miniature surface mount packages are the most popular style, and are readily available on tape and reel for use in automated assembly applications.
-
product
2-Way Resistive Power Dividers DC To 40 GHz
Pulsar Microwave manufactures resistive dividers from DC to 40 GHz. They have a rated input power of one half watt maximum. VSWR of 1.5:1 or better maintained throughout band at all ports. Resistive dividers can be fitted with SMA male or female connectors and are available in three outline packages.
-
product
4-Way Power Dividers From 0.5 To 60 GHz
Pulsar Microwave's 4-way power dividers are available in narrowband and broadband configurations, covering frequencies from 500 MHz to 60 GHz. They are designed to handle from 10 to 30 watts input power in a 50-ohm transmission system. Microstrip or stripline designs are utilized, and optimized for best performance.Units come standard with SMA or N female connectors, or 2.92mm, 2.40mm, and 1.85mm connectors for high frequency components.
-
product
SP2T RF Pin Diode Switches To 18 GHz
Pulsar Microwave's 2-way switches are available in absorptive and reflective designs from 20 MHz to 18 GHz. They are also referred to as single pole, double throw and abbreviated SPDT or SP2T. These switches have a typical VSWR performance of 1.6:1 or better and input power handling of 200 milliwatts maximum. Switching time is 100 nanoseconds, and isolation of 60 dB or greater for most models. Supply voltages are +5V and -5V, with TTL logic control voltage of 0 to 5 volts.Both absorptive and reflective SPDT switches are packaged into Pulsar Microwave's SW2 outline. Configuration is standard with SMA female connectors. Voltage is applied with wire wrap feed thru terminals. The housing serves as electrical ground, and two turret terminals are installed for wiring.
-
-
product
Dual Directional Couplers From 0.5 To 40 GHz
Dual directional couplers from Pulsar Microwave are available in standard values of 10, 20 and 30 dB with coupling tolerance of +/- 1.25 dB. They are available in narrowband and wideband designs from 500 MHz to 40 GHz. Most models have a coupling flatness of +/- 0.8 dB. Input Power is rated for 50 watts.
-
product
Directional Couplers From 0.01 To 2000 MHz
Pulsar Microwave's low frequency directional couplers operate within the frequency range of 10 kHz to 2 GHz. They're available in either surface mount or connectorized designs. SMA female connectors are standard, but BNC, TNC, F, N, jack or plug are available upon request.Most of these directional couplers have a flatness of +/- 0.25 dB and directivity of 20 dB or better within the operating band. VSWR of 1.3:1 or better maintained on all ports for most models. Maximum power handling is between 1 and 3 watts depending on model.
-
product
20 DB Directional Couplers From 0.5 To 60 GHz
Pulsar Microwave's 20 dB high frequency single directional couplers make up the CS20 series. They are available in narrow or wideband designs from 500 MHz to 60 GHz. They have a typical coupling tolerance of +/- 1 or 1.25 dB and most models handle 50 watts input power. These directional couplers are designed to operate in a 50-ohm system, and are optimized for best matching and high directivity with flat coupling response.Standard outlines are offered in SMA or N type female packages, either all of one type or combination with N type mainline and SMA coupled port.
-
product
3-Way Power Dividers From 0.5 To 35 GHz
Pulsar Microwave's 3-way power dividers cover 500 MHz to 35 GHz in various connectorized packages. They are rated to handle 30 watts maximum input power for a load VSWR of 1.20:1 or better. The 3-way power combiners are available in both in-line and Tee configurations, and come standard with SMA or N female connectors.
-
product
QPSK Quadraphase Modulators To 1880 MHz
QPSK Modulators incorporate a 90° hybrid, 2-way 0° divider and two BPSK Modulators to phase shift an input signal by 0°, 90°, 180°, and 270° by injecting ± 20 mA control signals at ports D1 and D2.
