HITEC Sensor Solutions Inc.
HITEC Sensor Developments designs and manufacturers load cells, strain gaged based force and torque sensors, instruments and complete test systems, and is an innovator of custom sensor solutions specific to a customer’s application.
- 978-742-9032
- 978-742-9033
- 10 Elizabeth Drive
Chelmsford, MA 01824
United States of America
-
Product
Fail Safe Mechanical Speed Sensor
95004
-
The Fail-Safe rotary speed control is a fluid/magnet actuated mechanical switch. It incorporates the consistent and dependable forces of gravitation and magnetism to achieve its mechanical switching action. Because the unit requires no electrical power to operate, it can be used in remote areas where access to power supply is inconvenient or unavailable.
-
Product
Load Washer
5000 Series
-
The Load cell is a stainless steel sub-miniature strain gage based transducer with compensated temperature performance. This type provides measurements up to 20000 lbf with better than ±0.5% (full scale) non-linearity
-
Product
Vehicle Test Sensors
-
Today's engines contain sensors to tell the vehicle's computer what's going on. Car sensors check for fuel-air mixture, incoming air temperature, wheel speed, and manifold pressure. They then tell your vehicle's computer what to do, based on that information.
-
Product
4-20mA Bridge AmplifierR
90416
-
This miniature, on-board, transducer amplifier is capable of supplying excitation voltage and amplifying millivolt signals from strain gage based transducers.
-
Product
Sensor Products: Weld Force Probe Auditing System
90061-XH Series
-
This system is ideal for field measurement and data logging of forces between the tips of resistance spot welders. The system consists of a handheld sensor and portable readout/ data logger (PMAC 2000).
-
Product
Mark II Dual Setpoint Monitor
95006
-
A patented, precision, solid state motion sensor consisting of a sensing head (encoder) and a master control panel and enclosure, the Mark II features a digital tachometer and a two-set point system. Use of a dual set point system, properly set, assures warning of a potential problem, allowing corrective action before damage can occur, and providing total shutdown if the problem is not corrected.
-
Product
Sensor Products: Weld Force Gage
90061
-
Model 90061 is a self-contained, portable measurement system which allows auditing of the pinch force generated between the electrodes of resistance spot welders. Resistance welding uses a pair of electrodes to clamp two base metals firmly together prior to and during application of electrical current. Poorly clamped parts result in a defective joint. A correctly clamped assembly aids in reducing the resistance in the joint and allows the current flow to properly heat the base metals to weld the part.
-
Product
Force Sensors
-
Is defined as a transducer that converts an input mechanical force into an electrical output signal. Force Sensors are also commonly known as Force Transducers.
-
Product
Mark I Single Setpoint Monitor
-
The Mark I is a self-contained unit featuring a single set point control. A simple two-step adjustment permits detection of an overspeed and/or underspeed condition at either 10% or 25% of operating RPM.
-
Product
Peak Track Instrument
90323
-
The model 90323 Peak Track Instrument is a general-purpose sensor readout device designed to complement our AutoID line of load cells and torque sensors. AutoID is a term that indicates that the calibration information for a sensor is stored on a chip inside the sensor’s connector. AutoID allows true “plug and play” operation without manual calibration procedures of any kind. The unit is also equipped with a 2-line alpha-numeric display and single button operation for simplicity.
-
Product
Miniature S-Beam Load Cell
500 Series
-
The Miniature S-Beam Load Cell is a bi-directional Aluminium strain gage based transducer with high performance and builtin temperature compensation. This design provides better than ±0.1% (full scale) non-linearity and includes overload protection in both tension and compression directions. Options include IEEE1451.4 TEDS capability.
-
Product
Threaded Load Button
2000 Series
-
This model is a threaded load button for tension and compression load measurements up to 5000kg/ 10000lb. Fully welded cover (for SS load buttons), amplified and digitised versions are available on request. We can also customise this sensor for other thread sizes and cable sizes
-
Product
Press Force Load Cell
6000 Series
-
Press Force Load Cells are strain gage based transducers for press-force monitoring. This type offers capacities up to 100 kN with compensated temperature performances. Cable is contained within a stainless steel spring for strain relief purposes for additional protection.
-
Product
In Line Load Cell (200N-5000N)
100 Series
-
Miniature Threaded in Line Load Cells are strain gage based transducers with temperature compensation and excellent overall performance. This type measures tensile and compressive loads up to 5000N with better than ±0.25% non-linearity.
-
Product
Power Monitoring Dynamometer
90085
-
Model 90085 is designed to measure machine tool output. This model acquires the necessary torque and speed data needed to calculate the horsepower of the machine tool under test conditions. It is a portable, self-contained data acquisition and monitoring system consisting of three major components: a pneumatic brake assembly, a torque and speed transducer, and the control and display module.
