King Design Industrial Co., Ltd.
It mainly produces reliability laboratory product testing instruments. Specializes in manufacturing and selling various vibration testing machines, impact testing machines, drop testing machines, etc., and has won a number of technology patents.
- + 886 2 2662 5100
- +886-2-2662-3094
- 5F., No.3, Lane. 270, Sec. 3, Beishen Rd.
Shenkeng Dist.
New Taipei City, 222
Taiwan, Province of China
-
product
Precise Ball-fall Tester
King Design Industrial Co., Ltd.
*Auto-lift device; accuracy is to 1mm*Precise-casting formed; won’t influence floor structure.*Good test-repeatability; easy to operate.*Can measure the hit time & maximum shock force.*Conform to CNS & JIS specifications.*Can output report, save file and make record.*Can extend the optingal functions and measure joule.*Anvil seat size can be changed to any size.* Chinese measuring interface; easy to comprehend and operate.*Timely observe the energy and shock force.*Pull-down window; fast in setting.
-
product
PyroShock
King Design Industrial Co., Ltd.
*Bullet:0.1~1.0 Kg*Pressure:30Kg/cm2 Max*Velocity:>1000m/sec
-
product
Bypass Diode Thermal Test System
King Design Industrial Co., Ltd.
* Power: the heating board control panel uses 220V single-phase power.* Power consumption: 1.0KVA, 1000W(Max)* Volt: 220VAC* Current: 4.5A* Heating board: one controller per board* Power rate: room temperature raise to 75°C± 5°C within one minute.* Heating board dimension: 500mm x 1,000mm* 6-sheet electrical heating boards test: used to test the 2,200mm x 2,600mm module. It can be customer-designed.* The length of board power cable and thermal sensor cable shall exceed 3,000mm.* To get uniform heating effect, the electrical board is sandwiched by 2mm aluminum sheets at both sides of board.
-
product
Large-Displacement Low-Frequence Vibration System
9363-LN-100
King Design Industrial Co., Ltd.
This tester is designed to assess the damage made to product packaging and internal objects caused from transporting environment; to discover the packaging flaw and product’s early failure from a long-term cumulative vibration fatigue; avoid man-made transporting damage and improve product’s reliability and quality of delivered products. With the use of high-performance foot absorber, the resonance effect to floor caused by the bounce test may be waived; and can reduce the pile’s destruction to industrial plants. Two displays can make comparative display on both frequency and rpm at the same time; thus no need to switch in order to read these two values. The dual-control mode of time accumulator and counter can avoid human error resulting from the conversion. Easy to operate; no need for complicate training program.
-
product
Modal Analysis Shaker
KD-9363EM-Analysis shaker
King Design Industrial Co., Ltd.
This machine can test the structural properties of materials, manual fine-tuning vibration frequency can perform single-point resonance search and presence; after shaking, capture resonance excitation modal analysis data for future use.
-
product
Instant Circuit-break Detector
King Design Industrial Co., Ltd.
*Independently detect instant circuit-break.*Can detect 10 loops simultaneously.*Minimum test range is 0.1 us.*Can follow product’s test condition to set the instant circuit-break monitoring time (0.1us~).*Beeper and indicator will rise up at instant break.*Accept customized order.
-
product
Cut Susceptibility Tester
King Design Industrial Co., Ltd.
Equipment conforms to IEC61730 MST12 specification. Pre- or post-round can be selected for control wiring connection. With weights block’s positioning pin is removed before test; and is inserted in the rear positioning hole for the remaining time. Equipped with rings at both front and rear end; used to connect a rope and control the driving direction. Use replaceable special cutting chip.
-
product
Automatic Huge Drop Tester
KD-8688
King Design Industrial Co., Ltd.
Reliability & Photovoltaic (PV) Testing Equipment.
-
product
High-acceleration Shock Tester
DP-1200-18
King Design Industrial Co., Ltd.
The precise-type high-acceleration shock tester can provide all half-sine short wave specification specified in JESD22-B110. To meet them, merely change different shock rubber-pad on shock seat. The wave is complete with high repeatability, able to provide user accurate test result.Conform to different test specs such as JESD22-B110 and IEC spec.High repeatability on consecutive shock; acceleration +/- 10%; run time +/- 15%; speed deviation +/- 10%.Table’s four corner-points uniformity P160mm +/- 10%.Can add spring system to reach the requirement of extra high acceleration specification.Using high-efficiency vibration-absorbing seat pad can block out possible floor resonance and protect the factory structure.Easy in operation; no complicate training course required.Module shock rubber-pads are applied per different standards independently. And the rubber-pad lifetime can be prolonged.
-
product
Drop Tester
KD-2768
King Design Industrial Co., Ltd.
Drop tester is applied to test the anti-vibration, covering-protection capability of packaging material, or product’s impact-resisting capability to determine the improvement parts of related packing design, material and structure. It contribute to promote the packing material and product’ strength. According to the result of packing drop test, you can judge whether the product has reach the required strength encountered in future. Through doing the drop testing of product independently, you’ll know its affordability to withstand external impact and assess the damage.
-
product
Bump Tester
KD-163
King Design Industrial Co., Ltd.
*Comply with IEC-68-2-29 testing specification(10g/ 16ms、15g/6ms、 40g/6ms、100g/2ms).*Easy installation and simple operation; Low noise; no maintenance required; function holds long.*Well-designed and no resonant-structure, air anti- vibration pad can effectively isolate floor vibration.*Accelerometer adopts repeated measurement and adjustable half-sine wave generator; to control the data is precise.*Magnesium alloy platform is anodized, Servo motor cam to drive, and can adjust the frequency automatically.*The adjustable acceleration value and shock domain is patent design (1ms-13ms).
-
product
Conduit Bending Tester
King Design Industrial Co., Ltd.
Equipment complies with IEC 61730-2:2004 MST 33 specification.
-
product
Wet Leakage Current Test
King Design Industrial Co., Ltd.
The outdoor solar module will endure the erosion of rain, fog, snow and sandstorm. To make sure that solar module will not wet leakage current accident and tolerate huge load pressure in such harsh conditions, we adopt wet leakage current to simulate the above weather conditions.
-
product
Shock Tester
DP-1200
King Design Industrial Co., Ltd.
Shock or bump test mainly simulate the impact effects of product and its components encountered in usage and transit process. Through standard and high-reproducibility instant energy exchange, you can analyze the product ability to tolerate the strong external stress and the degradation of structural weaknesses to quickly obtain the data of structure strength, anti-shock appearance and anti-drop. Shock tester is one of destructive experiments, and do destructive test on the product to evaluate the product reliability and monitor the consistency of production line.
-
product
Indoor Multi-Light source of Measurement System for PV Cell
King Design Industrial Co., Ltd.
The multi-light source measurement system is capable of execute I-V measurements by Real-Time One-Sweep Method (RTOSM), which not only removes the capacity effect but also meets the requirements of SEMI PV57-1214. The measurement process is controlled by designed program, thus the measured I-V curve, Pmax/Isc/Voc/… etc, could be exported automatically.This system is applicable to DSSC/OPV/Perovskite measurements.
