Pulsed Lasers
A single or repetitive burst of laser energy with a pulse equal to or less than 0.25 s in duration.
See Also: Autocorrelators
-
product
High Voltage Pulse Attenuators
Barth High Voltage Pulse Attenuators are matched impedance coaxial attenuators for use primarily in pulsed 50 ohm systems, or where occasional transients would damage ordinary units. The attenuator design closely matches the impedance around each resistor, to that resistor. These attenuators feature an input impedance very close to 50 ohms, with characteristics as good or better than most microwave attenuators. These units are ideal for use in nuclear and high energy experiments. Extensive testing during manufacturing insures very high reliability for single-shot experiments. A voltage coefficient of the resistive film of less than .0001 %/V allows low voltage calibration of most systems.
-
product
Laser Distance Meters
PeakTech Prüf- und Messtechnik GmbH
This professional laser distance measuring device with multi-line LCD display, which has a backlight, was specially designed for high-precision distance measurements.
-
product
Infrared Thermometer with Laser Pointer
Professional Infrared Thermometer with Laser Pointer - Safely measure hot, hazardous, or hard-to-reach materials without touching the material's surface; simply pull the trigger & read the temperature
-
product
*Laser Spectroscopy
*Sum Frequency Generation (SFG) vibrational spectroscopy and microscopy*Investigation of surfaces and interfaces of solids, liquids, polymers, biological membranes and other systems
-
product
Broadband Mid-Infrared Femtosecond Laser Source
FemtoFiber dichro midIR
The new FemtoFiber dichro midIR represents an ideal laser source for mid-infrared spectroscopy and imaging. It provides a tunable broadband output in the wavelength range of 5 to 15 m (20 - 60 THz, 670 - 2000 cm-1). The unique 400 cm-1 broad emission spectra allow to excite a wide range of materials at the same time. The air-cooled system is based on TOPTICAs proprietary fiber laser technologies and includes a difference frequency generation (DFG) unit as well as all necessary electronics into the same box. All functions and features are computer controllable by Ethernet or USB interfaces.
-
product
PXIe Source/Measure Unit, 15 MSa/s, 1 PA, 60 V, 3.5 A DC/10.5 A Pulse
M9602A
The Keysight M9602A is a PXIe SMU featuring best-in-their-class narrow pulse width as narrow as 10 μs. It enables dynamic/pulsed measurements with up to 15 MSa/s for broad emerging applications such as VCSEL optical devices.
-
product
PRO8 Modular Laser Diode Platform
Thorlabs offers the PRO8 modular test and measurement platform in 2-slot and 8-slot configurations. These customizable bench top chassis let users build a compact fiber or laser diode testing platforms for their lab or factory floor. Modules include lasers, TEC controllers, optical switches, and current controllers.
-
product
Laser Head Cable, 20 m
10881C
Provide reliable power with this five-pin female DIN that connects the laser head to multiple laser boards.
-
product
Laser Diode Reliability Burn-In / Life-Test System
58602
Chroma 58602 is a high density, precision multi source measurement Unit (SMU) module with temperature control and exchangeable interface developed for burn-in, reliability and life test of optoelectronic components including laser diodes, VCSELs, VCSEL Arrays, silicon Photonics, photo-diodes and other similar components.
-
product
Laser Diode Drivers
Renesas offers a portfolio of laser diode driver (LDD) ICs for DVD/CD/Blue-ray optical drive and laser projection applications.
-
product
Pulse Pattern Generator, 3.35 GHz, single channel
81133A
The Keysight 81133A single-channel 3.35 GHz Pulse Pattern Generator is the latest product in the long history of Keysights high-speed Pulse Pattern Generators. When timing and performance requirements are critical, for example in high-speed serial bus applications like PCI Express or Serial ATA, its fast rise times and low intrinsic jitter allow the precise and in-depth characterization of devices, e.g. receivers or backplanes. Like its predecessor, the Keysight 8133A, the new 81133A sets the standard for high-speed applications. The Keysight 81133A lets you test your DUT instead of the pulse or data source! For applications that require multiple output channels or multi-level signaling like pre- and de-emphasis (PCI Express) or squelch (Serial ATA), please refer to the 81134A.
-
product
Digital Laser Sensor
LS-400
Panasonic Industrial Devices Sales Company of America
The LS Series Digital Laser Sensor combines a highly focused, concentrated laser beam with a coaxial optical lens system to detect extremely small objects from long distances. This Series is particularly suitable for monitoring or detecting extremely small objects on a conveyor belt, for monitoring the sizes of objects and for monitoring edge positions in industrial production.
-
product
150A, 12 MHz CURRENT PROBE, BNC, AC/DC, 150A rms, 300A Peak Pulse
T3CP150-12
150A, 12 MHz CURRENT PROBE, BNC, AC/DC, 150A rms, 300A Peak Pulse.
-
product
DC Pulse Current Capacitor
Both series can be customized as Low Voltage High Capacitance High Current Capacitors.We can customize Snubber Capacitor as Box type and support other parameters.For 250Vac~900Vac / 400Vdc~1,350Vdc and with higher Current requirement, please refer to our AC/DC Power Capacitors.Different applications can have very different capacitor electrical and mechanical profile requirements.Please feel free to send your application details for a suggestion and quotation.
-
product
Laser Distance Meter M-LDM-50P
Laser Distance Meter M-LDM-50P
Fuzhou Metricu Technology Co Ltd
Laser Distance Meter
-
product
Digital Pulse Processor For X-Ray Spectroscopy
Dante
The Digital Pulse Processor for X-Ray Spectroscopy
-
product
150 A, 10 MHz Current Probe - AC/DC, 150 A rms, 500 A Peak Pulse, 2 meter cable
CP150B
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
product
Pro Laser Tachometer
332
The #332 is the ideal tool for easy and accurate measurement of RPM in almost any environment. Simply aim the laser beam at a reflective mark placed on a rotating device, push the button and the RPM reading is immediately displayed. No contact with the shaft or wheel is necessary. The laser beam is not affected by shop light and can detect RPM from longer distances of up to 6 feet away. The #332 can measure up to 99,999 RPM in 1 RPM increments. It can be used to measure RPM on coil-on-plug and diesel engines, where conventional inductive tachometers can not be used. Other uses include generators, compressors, industrial engines, fans, gears and more. Zippered case, reflective tape, instructions & 9V battery included.
-
product
Laser & LED Testing
Lasermet is the UK’s leading test house for testing to the following standards:EN 60825-1 / IEC 60825-1*EN 60825-2 / IEC 60825-2EN 60825-12 / IEC 60825-12*EN 60601-2-22 / IEC 60601-2-22*21 CFR 1040.10and is the only test house with UKAS accreditation for laser and LED testing (other than the National Physical Laboratories).
-
product
Laser Doppler Surface Velocity Meter
LV-7000 series
The LV-7000 series detects speed, uneven speed, distance, length of moving object or rotating object without contact. By contacting with 2 sensors, it enables to calculate difference in velocity/length between the two points in real time and output with 3,000 ppm of accuracy. The frequency response can be expanded up to 20 kHz, which achieves to understand phenomena and evaluate mechanical systems at high speed, efficiently, and accurately. It is useful for evaluation of motor control and behavior measurement, improving parts quality, and reducing loss of material.
-
product
Sapphire Defect Laser Probe and Glasses
LP-100
Easy to use and portable■ low price with long lifetime■ can be used to detect many defects, like micro crack, bubbles, impurity, crystal subgrain■ When the laser go though the crystal, if it is monocrystal the light should be scattering, in macro it should be white.
-
product
Laser Power and Targeting
ST60 Quad
A four-channel silicon-based thermopile detector in a TO-5 package. Each small active area size is 0.61mm x 0.61mm. This is our lowest-cost and fastest time constant four-channel detector. It delivers a time constant of 18ms with Nitrogen encapsulation gas combined with a very low Temperature Coefficient of Responsivity of -0.04%/C. This detector has a very short thermal shock response to ambient temperature change.
-
product
Tunable Diode Laser Absorption Spectroscopy
5100HD TDLAS
Using tunable diode laser absorption spectroscopy (TDLAS) technology, the 5100HD can be configured with one or two absorption cells, providing dual stream analysis and/or the measurement of multiple analytes at the same time.
-
product
Hydraulic Pulse Fatigue Testing System
PFT-500
Jinan Testing Equipment IE Corporation
PFT-500 hydraulic pulse fatigue testing machine is mainly applicableto large size parts such as bridges, trusses, automotive chassis, front and rear axels, locomotive frames, chassis and various concrete structures for static compression test and dynamic unidirectional pulse fatigue tests. The Fatigue Testing System for Rail has significant characteristics of reliable design, simple operation, energy conservation, and low operation cost etc.
-
product
Amplifier-separated Type Digital Laser Sensor
LS-500
Panasonic Industrial Devices Sales Company of America
The LS-500 Series Amplifier-Separated Type Digital Laser Sensor offers high-class Laser Sensors able to detect very small objects with a processing speed of down to 60µs. The new full stainless steel M6 housing is robust and optimally suited for applications in harsh environments. The unique controller can handle Thru-Beam, Diffuse Reflection and Retroreflection Laser Sensor heads. All Sensors are equipped with two digital outputs, and cable-type Sensors offer an additional analog output, opening new dimensions in the detection of small objects.
-
product
Laser Hunter - gas detection & gas measurement device
Highly sensitive and selective gas detection & gas measurement device withlaser technology for the inspection of underground gas pipes using suitableprobes (e. g. carpet probe). The device can also be used for the vehicle-basedpipeline inspection.With built-in diaphragm pump, Bluetooth module and rechargeable Li-Ion battery.The following applications are possible:- Inspection of underground pipes- Inspection of accessible pipes in buildings- Inspection of accessible pipes on plants, etc.- Inspection of ground soil for pinpointing (optional)- Purging of gas pipelines (optional, only in combination with pinpointing)- Gas analysis (with dual laser module)
-
product
Laser Instrumentation
We have created a range of high-performance, compact laser instrumentation designed to capture, extract and view important data – making experiments easier to set up, manage and measure. Developed in conjunction with universities, our Ice Bloc system offers state-of-the art connectivity with a modern and accessible interface.
-
product
Medium & High Voltage Pulse Generators (Rise Time > 1 ns)
Offer fast medium voltage pulsing with high current capability. These models are ideal for driving solenoids, pulse testing of MOSFETs, and other applications.
-
product
Xenon Long Pulse Solar Simulator Three Target Sizes
Complies with IEC60904 Class A solar simulation standards.Up to 100ms of effective irradiated time is achieved. Through our proprietary filter technology, spectral concordance conforms to IEC / JIS Class A standards.Three systems provide a wide selection to meet your panel size, floor space, and performance requirements.
-
product
Laser Head Cable, 7 m
10881E
Provide reliable power with this spade lug that connects the laser head to multiple laser boards.
