MP4
group of audio video digital data compression standard formats.
-
Product
Permanent PQ & Energy Monitoring Products
-
Compact monitoring solution that combines PQ monitoring (with waveform recording) and 4 quadrant energy monitoring in one instrument.
-
Product
PXIe Performance Vector Signal Analyzer: 50 GHz
M9393A
Vector Network Analyzer
9 kHz to 8.4 GHz, 14 GHz, 18 GHz, or 27 GHz Frequency extension to 50 GHz (minimum frequency of 3.6 GHz) with Option FRX40 MHz (standard), 100 MHz, or 160 MHz analysis bandwidth, and optional wideband IF output with Option WB1Up to 4 time-synchronous channels
-
Product
Fixed-Frequency Synthesizer
MI Series 3.5” x 2.5” x 0.6”
-
*Connectorized Package *Up to 4 Independent RF Outputs *Output Power to +13 dBm Available *Low Power Consumption (<1 Watt) *Optional Internal Reference
-
Product
2-Slot BRIC, 128x8, 1 Pole, PXI Matrix (2 Sub-cards)
40-559-201-128x8
Matrix Switch Module
This range of BRIC ultra-high-density large PXI matrices are available in 2, 4 or 8-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
Product
Burst-Generator
SFT 1420
-
The test generator SFT 1420 simulates quick transient noise interference as they are defined in the standard IEC / EN 61000-4-4. The single pulses show a very short rise-time (5 ns) and due to this a wide RF-spectrum up to 300 MHz. RF interferences are the result.
-
Product
General Purpose 4 Channel Optocoupler Board
-
A general purpose 4 channel optocoupler board using H11G2 optocouplers (see above schematic). Resistors, capacitors, and connections to terminal strip are made by customer to allow for complete flexibility
-
Product
Digital Controlled Phase Shifters To 4 GHz
-
Pulsar's Digital Controlled Phase shifters utilize PIN diodes and delay lines to produce the necessary phase requirements. These digital phase shifters use switched lines to obtain temperature stable phase shift. The phase is specified at the center frequency ± 3.0% and is proportional to frequency over the entire band.
-
Product
PXI 8 Slot BRIC 72x16 2A 1-Pole Matrix
40-598-103
Matrix Switch Module
The 40-598 PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps or 100VDC/70VAC. The 40-598 BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
PXI Analog Output/Current Loop Simulator Module - 8 Channel
41-765-003
Analog Output Module
The 41/43-765-003 is an 8-channel Analog Output Module designed to meet the requirements of industrial control applications utilizing current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signaling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
Product
Linear Testfixture for VPC iCon i1 Mass Interconnected Cassette Interface (Cassette Not Included) 4 or 10 Positions Blocks, UUT 586 x 248 mm
MG-03-01
-
FEATURES• Linear click system with ball bearings, using gas springs• 10 mm ESD-proof top cover with aluminium reinforcement bars• Steel base cabinet with detachable aluminium back and bottom panels• Detachable interchangeable case system with an 8 mm spring loaded probe protection cover• Base cabinet fitted with a telescopic guide rail and catchTECHNICAL SPECIFICATIONS• Max. number of probes (2000N) 1300 units• Max. PCB height: 60 mm• Linear travel: 12 mm• Max UUT: 586 x 248 mm (wxd)• Outer dimensions: 750 x 490 x 100 x 170 mm (wxdxh1xh2)• Designed for Mass interconnect changeable cassette• Up to a maximum of 8 interface blocks of 160 or 170 signals• All interface blocks can be customized
-
Product
PXI 8-Slot BRIC 24x8 Matrix, 2A 2-Pole (1 sub card)
40-565A-102-24X8
Matrix Switch Module
The 40-565A PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps at 150VDC/100VAC The 40-565A BRIC modules are available in 2, 4 or 8 slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using quality electro-mechanical relays for high switching confidence.
-
Product
Squid Carrier Board™ Family PCI Express Gen 3 Carrier Board for 4 M.2 PCIe SSD Modules
SKU-086-B4
-
B-series PCI Express Gen3 Carrier board was designed as a cost-effective storage solution for the systems that are using a motherboard with PCI Express bifurcation support. Such motherboards can be configured in the BIOS to split x16 PCI interface to four PCI Express interfaces by utilizing the following PCIe lanes:- x4 PCI Express interface 1: lanes 0,1,2,3 from x16 PCIe interface;- x4 PCI Express interface 2: lanes 4,5,6,7 from x16 PCIe interface;- x4 PCI Express interface 3: lanes 8,9,10,11 from x16 PCIe interface;- x4 PCI Express interface 4: lanes 12,13, 14, 15, from x16 PCIe interface;
-
Product
XMC-PCIeStor, High Speed PCIe Quad M.2 SSD Adapter
9303
-
The 9303 is an air or conduction cooled, extended temperature XMC card with 4 M.2 SSD sites for multi-terabyte storage. Onboard Gen2 PCI Express (PCIe) switch connects one 4-lane upstream PCIe port to four 1-lane downstream ports.
-
Product
Fanless Embedded System With LGA1151 Socket 7th/6th Gen Intel® Core™ & Celeron® Processor, Intel® Q170, 2 HDMI, DisplayPort, 4 GbE LAN, 8 USB, 2 PCI Express Mini Card Slots
eBOX670-891-FL
-
The eBOX670-891-FL supports the 7th/6th generation Intel® Core™ i7/i5/i3 and Celeron® processors with flexible I/O configurations. This outstanding embedded box PC is equipped with dual DDR4-2133 SO-DIMM slots with system memory up to 32 GB. The eBOX670-891-FL provides high flexibility with reserved I/O module space on the rear side. The embedded system integrator can expand the system quickly and easily by installing suitable I/O modules. The fanless embedded box computer features wireless communication capabilities with two internal PCI Express Mini Card slots and one SIM card slot. Four Gigabit Ethernet ports are for customers who need mass data transmission or LAN port teaming functions for each virtual machine. For storage needs, it is equipped with one easy-access CFast™ socket, one mSATA interface, and dual 2.5” SATA hard drive bays with RAID 0&1 support.
-
Product
Multiprotocol Serial Card
PCIe-ICM-4SM
-
The PCIe-ICM Series are a new family of isolated PCI Express serial communication cards. These PCI Express cards feature a selection of 4 or 2-ports of isolated, software selectable, RS-232, RS-422, and RS-485 serial protocols.
-
Product
8/4-Ch, 14-Bit, 10 MS/s Per-Channel Simultaneous Analog-Input PCIe DAQ Card
PCIE-1842
-
8 or 4 x Simultaneously Analog Inputs, up to 10 MS/s14-bit resolutionSupports digital and analog triggersWide input range up to 20 Vpp (±10 V range)Onboard FIFO memory (65,536 samples)
-
Product
PXI 8 Slot BRIC 33x16 1-Pole (3 sub-cards)
40-562A-121-33X16
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 8 Slot BRIC 22x16 1-Pole (2 sub-cards)
40-562A-121-22X16
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
Portable Slimline Tube Tester
741200
-
Battery powered high-frequency generator for testing pumped neon tubes and fluorescent lamps, operates on 4 AA batteries. Tube being tested will illuminate in a pulsating manner if “good”. Includes leather case. 6-7/8” long x 1-1/2” wide x 3/4” deep. Batteries not included.
-
Product
Optical Fiber 1×4 Switch
OFSW - 1 × 4
-
Hangzhou Huatai Optic Tech. Co., Ltd.
OFSW- 1×4 is a 1×4 prism optical switch. It can support 1 optical fibers input and 4 fiber output, channel switch. Wide operating wavelength range, low insertion loss and speedy switching rate, can use network trends configuration, network monitor and lab application.
-
Product
UPS (Uninterruptible Power Supply)
-
The UPS (Uninterruptable Power Supply) by Allied Edison is a light weight (7.2 lbs), portable, non-variable source that converts a 12 Vdc Lithium Ion battery to output 110 vac sine wave at 60 hertz. It also has four 12Vdc output jacks, and 4 USB ports to power electronic equipment such as computers or used to supply cell phone chargers, etc. It has a strong built in flashlight. The UPS plugs into a standard 120 Vac, 60 hertz receptacle for charging and indicates percent battery capacity remaining on a digital meter located on the front panel. The UPS can also be charged by a solar cell, sold separately or can be plugged into a vehicles cigarette lighter receptacle for use in remote areas. The UPS is an excellent compliment to the VS-3 power supply where a technician needs a variable AC/DC source and cannot run a power cord due to the remoteness of the work area.
-
Product
10-Pole Test Switch Protectors
6441 & 6441-C
-
With safety always being a concern while working with electrical boxes, you can depend on TESCO’s Test Switch Protectors (Catalog No. 6441 & 6441-C) to alleviate any uncertainty. This was developed to provide temporary protection of the test switch and to address the rising concern that the terminals of the test switch are exposed while you’re working in the box. The switch protector can prevent incidental contact with live terminals or contact with tools. TESCO’s Test Switch Protectors are constructed of clear, flexible PVC with a voltage rating of 2500V. The switch protector will fit any brand of test switch, regardless of manufacturer, from 4 to 10-pole. TESCO can also develop custom designs of this product to meet unusual test switch configurations.
-
Product
8-Channel 200 MHz A/D with DDC, Virtex-6 FPGA - 6U VPX
Model 58661
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Eight 200 MHz 16-bit A/Ds- Eight multiband DDCs (digital downconverters)- Two multiboard programmable beamformers- Up to 4 GB of DDR3 SDRAM; or: 64 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Cable Assembly, Receiver, TriPaddle, 36", 10 Position Combicon and 4 Position Omnimate
540295010201
Cable Assembly
Cable Assembly, Receiver, TriPaddle, 36", 10 Position Combicon and 4 Position Omnimate
-
Product
Rugged ½ ATR for VITA 48.2 Payload Cards & VITA 62 Power Module - 4-Slots
SFF-ATR-VPX
-
This ½ ATR platform is designed for use in harsh environments. It is designed to house three 3U VPX (VITA 48.2) payload cards and one 3U VPX (VITA 62) PSU and protect them from harsh environments. The backplane supports up to 4 slots on a 1” pitch.
-
Product
Temperature Sensors
TT420-LT
-
Features• 2-wire, loop-powered 4-20 mA analog output• Attachment probe, sensor, and 2-wire 4-20 mA signal conditioner• Integral 1/2" flexible liquid-tight conduit fittings• TT420Z-LT 1/4” stainless steel probe with 1/8 NPT adapter• TT420S-LT 3/8-16 threaded stud probe • FM approved, Dust Ignition-proof• Class II and III, Div I (E, F, G); NEMA 4
-
Product
High-power DC Electronic Load (6kW~60kW)
FT68200A/AL/E Series
-
Shenzhen FaithTech Technology Co., Ltd.
FT68200 series high performance high-power DC electronic load provides three voltage ranges 150 V/600 V/1200 V, maximum current 2400 A per single unit, stand-alone power from 4 kW to 60 kW, expandable up to 600 kW, 10000A by master-slave paralleling. Ultra-high power density, 6kW is with only 4U height. Wider operating region, faster dynamic frequency, as well as transient mode, OCP/OPP test, sequence test, automatic test and battery discharge test functions greatly enhances its test strength and expands application coverage. Furthermore, two times instantaneous overpower loading capability can effectively reduces user’s test cost. Built-in standard RS232, RS485, LAN, USB (serial), optional GPIB and CAN interface, supports SCPI, ModBus RTU and CANopen protocol, which facilitates system integrators. FT68200 series has full protection functions, which can be applied to power battery discharge, DC charging station, charging piles, charging pile modules, vehicle On Board chargers (OBC), high-power switching power supplies, power electronics and other power electronics products.
-
Product
Analog Input Expansion Board
MSXB 018
-
The MSXB 018 Analog Input Expansion Board expands 16 analog input lines to 64 analog input lines. The MSXB 018 provides 4 expansion ports that are compatible with MSTB 009 Analog Termination Boards.
-
Product
Low-Profile Modular Power System Mainframe, 400W, 4 Slots
N6700C
Mainframe
The Keysight N6700C is a 400 W 1U high, 4-slot modular power system mainframe that accepts from 1 to 4 N6700 series DC power modules in any combination. Modules are ordered separately. The N6700C offers GPIB, LAN, and USB, interfaces standard, and LXI compliance. Select from more than 20 different DC power modules, ranging in capability from basic to high precision, and in power from 20 - 300 W.
-
Product
Modbus RTU Analog Input Modules
-
The Datexel range of Modbus RTU analog input cards for both RS485 and RS232 with Modbus or ASCII protocol can be combined with the DAT9000 series of Modbus Masters. A choice of input cards or modules are available and have various optional inputs such as Voltage, Current, Thermocouples, RTD, and Resistance. Also a choice of 2, 4, 8 channel options are available. The DAT3011 is a Modbus RTU Slave with 1 selectable universal input (Thermocouples, RTD, mV, RTD's or Resistance), 2 x 4-20mA or 0-10V input and 2 x4-20mA outputs. The DAT3011 also has 3 digital inputs and 3 relay outputs. Each module is isolated from each other and is set up using the DAT3000 software Development package which is free of charge from the Datexel download web page. Datexel also has universal input modules. An 8 channel analog input card is available making the DAT3000 series a very economical solution to large and small scale Data Acquisition. Combining these analog input cards with the analog output cards, the digital input/output cards and the communication devices make Datexel the smart choice where Data Acquisition is required.
