ADC
quantization of an analog signal into a digital signal.
See Also: Analog-to-Digital Converters, FPGA, Transducers
-
Product
4-Channel ADC Module
FMC164
-
Sundance Multiprocessor Technology Ltd.
The FMC164 is a digitizer FMC featuring four ADC channels with 16-bit resolution and a 250 Mega samples per second sampling rate per channel. With a flexible clock generation and distribution scheme, the FMC164 allows control on sampling frequency and analog input gain through serial communication with a carrier card. The FMC164 design is based on the TI ADS42LB69 Dual Channel 16-Bit 250 MSPS A/D, is equipped with power supply and temperature monitoring, and offers several power-down modes to switch off unused functions.
-
Product
FMC-HPC ADC Board
FMC123
-
Sundance Multiprocessor Technology Ltd.
The FMC123 provides four 16-bit A/D channels up to 1Gsps. The design is based on Texas Instruments’ ADS54J60 Analog-to-Digital converter. The sample clock can be supplied externally through a coaxial connection or supplied by an internal clock source (optionally locked to an external reference) for multi-channel synchronization. An external trigger input is available for timing synchronization. The FMC123 is mechanically and electrically compliant to the FMC standard (ANSI/VITA 57.1).
-
Product
4 Channel ADC FMC Module
ADCFN04 – HPC
-
Sundance Multiprocessor Technology Ltd.
The RFM-ADCFN04 is a four channel Analog to Digital converter FMC which complies with VITA 57.1-2010. Each channel provides DC coupled single-end analog input and digital output with DC-250KHz sampling speed based on Linear Technology’s LTC2376-16. The output is 16-bit data and it can be obtained through SPI interface on LTC2376-16 from the FPGA on the FMC carrier board. One trigger input is provided for capture control.
-
Product
64 Channel ADC for VMEbus
VME392
-
The VME392 features 64 self-contained ADC channels with a resolution of either 12 or 16-bit (see ordering information). This product is ideally suited for mass acquisition with high accuracy for reasonable cost. The 64 channels are grouped into four sections of 16 channels each. Each section behaves completely independent from the other sections.
-
Product
4-Channel ADC Module
FMC104
-
Sundance Multiprocessor Technology Ltd.
The FMC104 is a four-channel ADC FMC (FPGA Mezzanine Card) which is fully compliant with the VITA 57.1-2010 standard. The FMC104 card provides four 14-bit 250 MSPS A/D channels which can be sampled by an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. A trigger input for customized sampling control is also available.
-
Product
16 Channel ADC for CompactPCI
CPCI392
-
The CPCI392 16-Channel Common-Mode Input ADC card is very well suited to be used in applications in which autonomous signal conversion is an issue, as well as in standard mid-range applications. Enabled channels are scanned at maximum rate and conversion results are stored in shared memory. A local DSP performs the data acquisition and calibration transparent for the host.
-
Product
Octal 4 Gsps 12-bit ADC
ADF-O4012
-
The DEG ADF-O4012 FMC includes eight 12-bit, 4 Gsps RF analog-to-digital converters (ADC). The ADF-O4012 features a 16-lane, 24.75 Gbps JESD204C interface, flexible clocking and triggering options. This ADF-O4012 leverages two Analog Devices AD9209 MxFE (Mixed Signal Front End) ICs, elevating the technology to a new level of integration.
-
Product
Quad 250Msps, 16-bit ADC FMC
ADF-Q25
-
This FPGA Mezzanine Card (FMC) converts four channels of up to 900 MHz analog input bandwidth at 250 Msps and 16-bit resolution. Based on the VITA 57 specification, the ADF-Q25 enables direct coupling of unparalleled analog-digital conversion capability with the VME/VXS/AMC/VPX/PCI-E carrier board of your choice. DEG engineers have designed this product and associated HDL firmware to work with both Altera and AMD FPGAs.
-
Product
2 Channel ADC – High-Pin-Count
ADCFN02 – HPC
-
Sundance Multiprocessor Technology Ltd.
The RFM-ADCFN02 is a two channel Analog to Digital converter FMC which complies with VITA 57.1-2010. Each channel provides AC coupled single-end analog input and 16-bit single-ended output with 20-105MHz sampling speed based on ADI AD9650. Single-ended external clock, differential external clock or an internal clock from the FMC carrier board can be selected at the FMC for the AD converter through fine clock generator ADI AD9518-3.
-
Product
ATE For ADC Module
MS 1527
-
The Semi-ATE is used for testing the analog ADC. It shall carry out the functional test on ADC analog module. The ATE shall have all necessary IO signals on the connector end. The semi-ATE can carry out the functional tests on ADC analog module with host PC or laptop. It provides +15V, -15V, +5V & -5V to module and +2.5V high precision reference voltage. It can able to control keysight N6700B Power supply mainframe using RS422 interface.
-
Product
ADC Drivers Fully Differential Amplifiers
-
Differential amplifiers allow the process of single-ended input to complementary differential outputs or differential inputs to differential outputs. These amplifiers feature two separate feedback loops to control the differential and common-mode output voltages. Analog Devices fully differential amplifiers are configured with a VOCM pin, which can be easily adjusted for setting output common-mode voltage. This provides a convenient solution when interfacing with analog-to-digital converters (ADCs). ADI also offers a series of differential receiver products that convert differential input signals to single ended output.
-
Product
6ch ADC, 2ch DAC – High-Pin-Count
RFM-ADAFF62
-
Sundance Multiprocessor Technology Ltd.
The RFM-ADAFF62 is a six channel Analog to Digital and two channel Digital to Analog mixed converter FMC which complies with VITA 57.1-2010. Each AD channel provides AC coupled single-end analog input and 16-bit single-ended output with 20-105MHz sampling speed based on ADI AD9650. Each DA channel provides 16-bit single-ended input and one DC coupled differential analog output with 1 – 500MHz sampling speed based on Maxim MAX5888A.
-
Product
PXI Express Board Virtex-5 ADC Module
SMT791
-
Sundance Multiprocessor Technology Ltd.
The SMT700 is one of the first of a new range of Sundance cards that includes a direct connection to SLB (Sundance Local Bus) compatible mezzanine card, without the need for a Sundance TIM. This enables a variety of cards to be added to a system, for example extra Ethernet ports, video in/out, High speed ADC / DAC etc. Data from these extra cards (along with data from the SMT700’s own inputs – up to 1Gb/s Ethernet, 2.5Gb/s optical links, and RSL links) can be processed via the Virtex 5, or by another linked card or module.
-
Product
Dual 3-ADC PXI Express Hybrid Module
SMT702
-
Sundance Multiprocessor Technology Ltd.
The SMT702 is a PXI Express (opt. Hybrid) Peripheral Module (3U), which integrates two fast 8-bit ADCs, a clock circuitry, 2 banks of 1GByte DDR2 Memory each and a Xilinx Virtex5 FPGA, under the 3U format.
-
Product
Air Data Computer (ADC) Tester
MS 1122
-
The ADC tester is used in 2nd line maintenance is to check the functionality of ADC. This unit is a rugged customized hardware based on full functionality test of ADC. The Air Data Computer (ADC) Tester is a fully automated GO/NOGO tester with full functional testing in 2nd line maintenance. This tester is to test ADC at unit level and identify faulty Shop Replaceable Unit (SRU). This tester is also used to carry out PI checks on ADC before clear them for installation on aircraft. ADC Interface board designed to test full functionality of ADC. The Air Data Computer (ADC) test equipment shall be used for testing ADC of Tejas Aircraft. ADC test equipment shall verify the functionality against specifications during second line maintenance and pre-installation on the aircraft.
-
Product
6 Channel ADC FMC Module
ADCFN06 – HPC
-
Sundance Multiprocessor Technology Ltd.
The RFM-ADCFN06 is a six channel Analog to Digital converter FMC which complies with VITA 57.1-2010. Each channel provides single-ended analog input and 16-bit single-ended output with 20-25MHz sampling speed based on ADI AD9650. A DC coupled input is supported. Single-ended external clock, differential external clock or an internal clock from the FMC carrier board can be selected at the FMC for the AD converter through fine clock generator ADI AD9518-3.
-
Product
2-Channel ADC Module
FMC122
-
Sundance Multiprocessor Technology Ltd.
The FMC122 is a Dual-Channel Multi-Mode A/D FMC, fully compliant with VITA 57.1 Standards. The card provides two 8-bit ADC channels that enable simultaneous sampling of 2 or 1 channel with a maximum sample rate of 1.25 GSPS (2-channel mode) or 2.5 GSPS (1-channel mode).
-
Product
16-Channel ADC Module
FMC116
-
Sundance Multiprocessor Technology Ltd.
The FMC116 is a sixteen-channel ADC FMC Daughter Card which is fully compliant with the VITA 57.1-2008 standard. The FMC116 provides sixteen A/D 14-bit 125Msps channels which can be sampled by an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. A trigger input for customized sampling control is also available. The FMC116 has the HPC (high-pin count) connector, front panel I/O, and is conduction cooled capable.
-
Product
VME J1 4 Slot with ADC Connectors
101VMEJ104-0590
-
VME J1 backplane 4 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
Product
VME J1 7 Slot with ADC Connectors
101VMEJ107-0590
-
VME J1 backplane 7 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
-
Product
14 Bit ADC Card
FMCADC100M14B4CHA
-
Sundance Multiprocessor Technology Ltd.
The FmcAdc100M14b4cha is a 4 channel 100MSPS 14 bit ADC card in FMC (FPGA Mezzanine Card) format. By default it uses only signals from the LPC rows of the HPC connector that is mounted. The gain can be set by software in three steps: +/-50mV, +/-0.5V, +/-5V. An advanced offset circuit is used in the front-end design of the ADC board, and allows a voltage shift in the range of +/- 5V that is independent on the chosen gain range.
-
Product
VME J1 21 Slot with ADC Connectors
101VMEJ121-0590
-
VME J1 backplane 21 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
Product
3U VPX Virtex-7 FPGA ADC/DAC
VPX3-530
-
Curtiss-Wright Defense Solutions
The VPX3-530 combines multiple channel high-speed ADCs and DACs with a latest generation user programmable Xilinx Virtex-7 FPGA in a range of rugged build formats for demanding applications such as SIGINT, radar and Software Defined Radio (SDR).
-
Product
PXI Express Board Virtex-5 Dual ADC/ DAC module
SMT750
-
Sundance Multiprocessor Technology Ltd.
The SMT700 is one of the first of a new range of Sundance cards that includes a direct connection to SLB (Sundance Local Bus) compatible mezzanine card, without the need for a Sundance TIM. This enables a variety of cards to be added to a system, for example extra Ethernet ports, video in/out, High speed ADC / DAC etc. Data from these extra cards (along with data from the SMT700’s own inputs – up to 1Gb/s Ethernet, 2.5Gb/s optical links, and RSL links) can be processed via the Virtex 5, or by another linked card or module.
-
Product
1 Channel 100 MHz Flash ADC
NIMbox ADNN
-
NIMbox ADNN - 1 channel 100 MHz flash ADC with 3 programmable TTL I/O ports, 4 LE discriminators and 10 NIM or TTL I/O ports
-
Product
PXI Express Board Virtex-5 ADC Module
SMT742
-
Sundance Multiprocessor Technology Ltd.
The SMT700 is one of the first of a new range of Sundance cards that includes a direct connection to SLB (Sundance Local Bus) compatible mezzanine card, without the need for a Sundance TIM. This enables a variety of cards to be added to a system, for example extra Ethernet ports, video in/out, High speed ADC / DAC etc. Data from these extra cards (along with data from the SMT700’s own inputs – up to 1Gb/s Ethernet, 2.5Gb/s optical links, and RSL links) can be processed via the Virtex 5, or by another linked card or module.
-
Product
PXI Express Board Virtex-5 SMT941 ADC Module
SMT741
-
Sundance Multiprocessor Technology Ltd.
The SMT700 is one of the first of a new range of Sundance cards that includes a direct connection to SLB (Sundance Local Bus) compatible mezzanine card, without the need for a Sundance TIM. This enables a variety of cards to be added to a system, for example extra Ethernet ports, video in/out, High speed ADC / DAC etc. Data from these extra cards (along with data from the SMT700’s own inputs – up to 1Gb/s Ethernet, 2.5Gb/s optical links, and RSL links) can be processed via the Virtex 5, or by another linked card or module.
-
Product
32 Channel Multievent Peak Sensing ADC
V785
-
The Model V785 is a 1-unit wide VME 6U module housing 32 Peak Sensing Analog-to-Digital Conversion channels. Each channel is able to detect and convert the peak value of the positive analog signals (with >50 ns risetime) fed to the relevant connectors. Input voltage range is 0 ÷ 4 V.
-
Product
Octal 310 Msps, 16-bit ADC FMC Module
ADF-O310
-
The ADF-O310 ADC FMC module from DEG delivers eight channels, each with 16 bits of resolution at a sample rate of up to 310 Msps. Utilizing the Analog Devices AD9652, the ADF-O310 enables defense applications requiring higher dynamic range, greater ENOB and wideband sampling performance.
