IEC 61850
-
product
Accessory EFT/Burst generators IEC 61000-4-4
The field sources and the burst transformer are used to harden the device under test. They are powered by an EFT/burst generator.
-
product
IEC Potential Transformer Burdens
• Burdens for IEC specifications rated for various input voltages available • 2.5 to 207.5 VA at 0.8 PFIEC Potential Transformer Burdens
-
product
Mineral Insulated Thermocouples IEC
Durable Mineral Insulated type thermocouples to suit a wide range of temperature measurement. Various probe types, lengths and diameters available.
-
product
IEC 60884-1 Fig41 High Temperature Indentation Tester For Socket
CX-YH
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884-1 High Temperature Indentation Test Device For Insulatio Material ndentation Device : For pressure tests on plug pin insulating sleeves at temperatures to 200° C with 2.5N loads, according to IEC60884-1 figure 41, BS1363 figure 10. This apparatus has a rectangular blade (see IEC60884-1 figure 41A) with an edge 0.7 mm wide, to be used in the case of round pins, or a blade having a round
-
product
Coupling Decoupling Network for Conducted Common Mode Immunity Testing According to IEC 61000-4-6
CDN
The CDN M5 is intended to inject common mode disturbance signals to power supply of mains lines (unscreened) in the frequency range from 150KHz to 230MHz. A variety of calibration adapters and other accessories are available as an option. RF Standard connector: BNC type, AC socket 4mm safety bananas.
-
product
IEC 60068-2-75 IK Pendulum Hammer Impact Striking Element
CX-IKA
Shenzhen Chuangxin Instruments Co., Ltd.
The Pendulum hammer impact strking elements conform to the standard IEC60068-2-75 and IEC62262. It's used for IK07, IK08, IK09 and IK10 ratings.
-
product
IEC 61000-4-5 EN61000-4-5 Lightning Surge Tester, Surge Generator
506AX
Shenzhen Chuangxin Instruments Co., Ltd.
Automatic lightning surge generator (or Lightning surge immunity) is used to assess the power cord and connect the internal switch stood in line to connect the internal switch to provide a common basis for switching the natural world and lightning caused by the high-energy transient interference performance. Performance fully meets the IEC 61000-4-5, EN61000-4-5 and GB/T17626.5 standards.
-
product
Front Panels for Plug-In-Units | IEC
Front panels for plug-in-units according to IEC | with or without EMC protection | aluminum 2.5 mm | clear anodised
-
product
Thermocouple Bench Selector Switches 6 or 12 Way IEC, ANSI
A 6 or 12 way selector in a moulded housing with aluminium front and rear panels. The rear inputs are switched via a front mounted rotary selector switch to the single output socket. Internally wired with thermocouple compensating cable and available with IEC or ANSI thermocouple types K, J, T, N & R/S.
-
product
MCB Thermal Trip Calibration Test Bench (IEC 60898 Cl 9.10.1.2, Annex I.1, IS)
The test system is designed and customized to carry out 2.55*Intest as per Table 7 (test c) of IEC 60898 (also mentioned for routine testing of MCBs. The test is done at dc current to exactly analyze and correct the bimetallic properties of the MCB as far as thermal tripping is concerned. The unit comes with a pneumatically operated test fixture with in-built dc stepper motor that is controlled by a micro controller / PC to calibrate the breaker into a narrow tripping band programmed by the user.
-
product
IEC Current Transformer Burden
• Burdens of 1A and 5A for IEC & ANSI specifications are available • 40VA, 20VA, 10VA, 7.5VA, 6.25VA, 5 VA and different combinations of these at 0.8 PF 3.75, 2.5, 1.25 & 1VA at 1.0 PF
-
product
An IEC 61000-4-11 Full Compliance Voltage Dip SimulatorModel: VDS-2002
VDS-2002
NoiseKen's new VDS-2002 offers easy and accurate test and following features: Dip, swell, interruption and variation tests up to 16A 240V single-phase AC, interruption test up to 125V DC, preset levels 0%/40%/70%/120%, open and short mode selection for interruption and optional Windows software.
-
product
IEC Testing
International Electrotechnical Commission
F2 Labs can assist you in testing your electrical products to the applicable IEC standards. The IEC is the world’s leading organization for the preparation and publication of International Standards for all electrical, electronic and related technologies.
-
product
Medical Computer Equipped With MXM Graphics Module Supporting NVIDIA Quadro® GPU With 8th/9th Generation Intel® Core™ I7/i5/i3 In LGA1151 Socket. Compliant With IEC 60601-1/IEC 60601-1-2
MLB-3002
- 2x PCIe Gen3 x4 expansion slot for Full Height Half Length add on card, each slot is 25W power budget and additional Molex 4 pin power cable (12V/1.5A and 5V/2A) support- ADLINK MXM Graphics module support (Type A/B, up to 120W)- 8th/9th Gen Intel® Core™ i7/i5/i3, Celeron® processor- Dual SODIMMs for up to 64GB DDR4 non-ECC memory (dependent on CPU)- DisplayPort (2 from CPU, 4 from MXM)- 1x M.2 E key supporting 1630 or 2230 for Wi-Fi/Bluetooth module, 1x M.2 B key supporting 2242 or 2280 for SATA storage module- Reliable Molex type 12V DC-in connector- 1x Intel® i219-LM and 3x Intel® i210-AT
