Rapid IO
"the unified fabric for Performance Critical Computing"; rapidio.org
-
Product
CPCI 48 Input I/O Card with Zilog Z8536 I/O Controller
CPCI-48IN
Controller
The input board consists of three Zilog Z8536 controllers for DC input control. An FPGA provides the timing and control. Each input has its own optical isolation, and supports a hardware adjustable resistor/opto-diode combination for various input voltage ranges. An AMCC PCI controller provides the interface to the host computer. All I/O is accessible from the front panel.
-
Product
Isolated Digital I/O 60VDC, 150mA
OTP2 module no.186
Test Platform
The National Instruments PXI-6528, PCI-6528, and PXI-6529 Digital I/O Modules are isolated digital I/O interfaces for PCI and PXI. These modules can use inputs from NI 6528 and PXI 6529 devices to capture the status of sensors, actuators, and logic devices. NI 6528 devices have 24 SSR outputs for switching external devices with input currents up to 150 mA. The NI 6528 and PXI-6529 devices are suitable for a variety of applications, from automotive development and industrial factory automation to aerospace, laboratory research, and biomedical applications due to their high current handling capacity and isolation.
-
Product
56 Channel TTL I/O FPGA PXI Card
GX3756 Series
FPGA PXI Card
The GX3756 is a user configurable, FPGA-based, 3U PXI card which offers 56, TTL I/O signals. The module consists of a daughter card and the GX3700 FPGA baseboard which employs the Altera Stratix III FPGA.
-
Product
Digitaler I/O Mit 16 Kanälen
MDS
-
The static driver sensor module (MDS) is used to replace existing TS02 from previous MTS test systems. The possible pin extension allows to replace the systems MTS 200/210 (4 UCB with 4 MDS = 256 pins). A maximum of 1,024 MDS pins can be realized on the current MTS systems. Up to 4 MDS modules can be connected to one UCB (UCB03 or higher).
-
Product
PCI Express Digital I/O Boards
PEX-P8POR8i
-
PCI Express x1, 8-channel isolated digital input.8-channel PhotoMos Relay output. Includes one CA-4002 D-Sub connector.
-
Product
25-Pin D-SUB Female to 25-Pin D-SUB Male, I/O Multifunction Cable
154742-01
Multifunction Cable
Low Profile I/O Cable, 25-Pin Female DSUB to Male DSUB (1m)
-
Product
24-Ch Digital I/O Universal PCI Card
PCI-1737U
-
ISA-Compatible with PCL-72424 TTL digital I/O channelsEmulates mode 0 of 8255 PPIInterrupt handlingOpto-22 compatible 50-pin connectorsOutput status readbackPCI universal card
-
Product
Analog I/O module with 8 differential analog output channels
IO108
-
This I/O module is a dedicated analog output module with a resolution of 16 bits. Each of the 8 output channel has its dedicated D/A converter with an update time of 2.2µs. The output coupling of the module can either be ordered as differential or single-ended. Furthermore, several of these modules can be interconnected by trigger lines to synchronously update analog output channels among the different modules.
-
Product
I/O and Storage
-
With the addition of the innovative MMS line of “create it yourself” I/O products, your ability to configure exactly the right connectivity options to create a complete system has never been greater – or more flexible.
-
Product
Analog I/O and Digital Receivers
-
Curtiss-Wright Defense Solutions
Many mission-critical applications require small form factor solutions, but cannot compromise ruggedization requirements or I/O and processing performance. Our VPX, XMC, PMC and FMC module-based sensor I/O solutions are designed to handle the toughest operating environments while packing maximum functionality in a minimal physical footprint.
-
Product
I/O Analog Module with 32 single-ended analog output channels
IO110 I/O
-
This I/O module is a dedicated analog output module with a resolution of 16 bits. Each of the 32 output channel has its dedicated D/A converter with an update time of 3µs. The output coupling of the module is single-ended for all channels. The output range of each channel can be selected individually.
-
Product
PC/104 Multifunction Analog I/O Boards
104-AIO16A/E
-
The 104-AIO16A is a high-performance 16-bit resolution PC/104 board which provides speeds up to 500kHz for 16 single-ended or 8 true differential analog input channels. This multifunction board features an excellent price/performance value for precision PC/104-based data acquisition, control, or signal analysis of standalone environmental test stations, compact production test equipment, portable testers, avionics and other applications.
-
Product
PLD For Bridging, Infinitely Reconfigurable I/O Expansion.
MachXO
-
*Up to 27.6 Kbits sysMEM™ embedded block RAM and up to 7.7Kbits distributed RAM*SRAM based logic can be reconfigured in milliseconds using JTAG port*IOs support LVCMOS, LVTTL, PCI, LVDS, Bus-LVDS, LVPECL, RSDS*Up to two analog PLLs per device that enable clock multiplication, division, and phase shifting*Available in TQFP, csBGA, caBGA and ftBGA packages
-
Product
Ethernet 48-Channel Digital I/O Interface
2410
-
Controls/monitors 48 digital signals over Ethernet PWM output mode Programmable input debounce Input edge detection with asynchronous host notification Compatible with standard solid state relay racks Embedded HTTP and Telnet servers Open source API
-
Product
PCIe Digital I/O Board, 64 Optically Isolated I/O Channels, 5V
APCIE-1564-5V
-
32 digital inputs, 5 V, isolated16 interruptible inputs32 digital outputs, 5 V, isolated, 10 to 36 V, 500 mA/channelOptical isolation 1000 VWatchdog for resetting the outputs to "0" (when Power-On)Protection against fast transients, overvoltage, electrostatic discharge and high-frequency EMIInputs: voltage reversal, input filtersOutputs protected against short circuitOvertemperature and overvoltage protectionDiagnostic report in case of short circuits, overtemperature, voltage drop ...24 V power outputs with protection diodesShutdown logic when the external supply voltage drops below 5 V
-
Product
SparkFun 16 Output I/O Expander Breakout
SX1509
-
Are you low on I/O? No problem! The SX1509 Breakout is a 16-channel GPIO expander with an I2C interface – that means with just two wires, your microcontroller can interface with 16 fully configurable digital input/output pins. But the SX1509 can do so much more than just simple digital pin control. It can produce PWM signals, so you can dim LEDs. It can be set to blink or even breathe pins at varying rates. This breakout is similar to a multiplexer or "mux," in that it allows you to get more IO from less pins. And, with a built-in keypad engine, it can interface with up to 64 buttons set up in an 8x8 matrix.
-
Product
Analog I/O module with 32/16 multiplexed analog input channels
IO102
-
Fast 16-bit analog module with 32/16 multiplexed analog input channels and 4 analog output channels. This I/O module offers lower input sampling and conversion times than the IO101 and therefore leads to smaller overall driver latency time. It is similarly priced as the IO101 but comes with 4 analog outputs instead of 8.
-
Product
PXI-6239, 8 AI (16-Bit, 250 kS/s), 2 AO, 6 DI, 4 Sinking DO, Bank-Isolated, PXI Multifunction I/O Module
779626-01
Multifunction I/O
8 AI (16-Bit, 250 kS/s), 2 AO, 6 DI, 4 Sinking DO, Bank-Isolated, PXI Multifunction I/O Module—The PXI‑6239 is a bank-isolated DAQ device designed for current I/O. It offers analog I/O, digital input, sinking digital output, two 32‑bit counters, and digital triggering. The digital input and outputs are compatible with 24 V signals. It combines the safety and performance benefits of isolation with high-performance timing, amplification, and calibration technologies to offer accurate measurements and precise control. The PXI‑6239 is ideal for test, measurement, control, and design applications in environments with high voltages and electrical noise. You can use the PXI‑6239 to read from encoders, flow meters, and proximity sensors as well as control valves, pumps, and relays.
-
Product
4-Ch RTD Input EtherCAT Slice IO Module
AMAX-5015
-
RTD InputChannels : 4Input Connections : 2 or 3 wireResolution : 16 bit with ±0.1% FSR accuracySample Rate: 100 sample/s (per channel)Burn-out detection: Yes
-
Product
12-bit, 200KHz, 16SE/8DIFF Isolated AI, 4 12-bit AO, 8 Optically Isolated Dig. I/O, 24V, 24 TTL I/O
APCI-3110-16
-
The APCI-3110 is a 12-bit multifunction board for 3.3 V and 5 V PCI systems, with optical isolation up to 1000 V and a high throughput rate of 200 kHz. The PCI board has additional types of conversion: Sequence RAM, Auto Refresh, scan, timer or external event.Furthermore, the board has a PCI DMA, 2 watchdogs, 4 digital inputs and 4 digital outputs. Sensors, which allow to supply current signals instead of voltage signals, also can be acquired with the APCI-3110, as this board offers up to 16 current inputs. The board is protected against overvoltage and input filter and it is protected against high frequency emmission. With the free calibration tool you can do the fine adjustment on-site.
-
Product
ISA Isolated Digital I/O Boards
ISO-P32C32
-
The ISO-P32C32 is a 64-channel isolated digital input board, arranged into four isolated banks. Each input chanel use a photo-coupler input which allows either internal power supply or external power selected by a jumper. Isolated input channels 0 ~15 are designed into group A, channels 16~31 into group B, Isolated input channels 32~47 are into group A, channels 48~63 are into group B. The power supply of the input port may use the external power or the the power from the PC side using DC to DC converter. The board interfaces to field logic signals, which eliminates ground-loop problems and isolates the host computer from damaging voltages. The ISO-P32C32 has one 37-pin D-sub connector and one 40-pin header. Users can connect the digital signal through the second D-sub connector. Each D-sub connector contains 16 input channels and 16 output channels.
-
Product
8DI 2.4G WiFi IoT Wireless I/O With 1RS-485
WISE-4051
-
Supports IEEE 802.11 a/b/g/n (2.4GHz)Supported protocols: Modbus/TCP, TCP/IP, UDP, DHCP, HTTPs, MQTTStores 10,000+ data points locally with SNTP/RTC time sync and WDT auto connection recoverySupports RESTful web API in JSON format for IoT integrationWith UDP-based AES-128 encrypted wireless P2P, abnormal inputs can automatically trigger up to 16 WISE modules in the field
-
Product
Analog I/O Board
VME-3128A
-
The VME-3128A scans 16, 32, 48 or 64 channels, continually digitizes all of them and stores the results. Choose from 64 differential or single-ended inputs and program VMEbus interrupts and interval timer to meet the unique requirements of your mission.
-
Product
Desktop/Wallmount Chassis With Front I/O Interfaces
IPC-5120
Chassis
Desktop/Wallmount Chassis with front I/O Interfaces for mATX Motherboard. With front I/O interface and four expansion slots, Shockproof drive bay for one 5.25" ODD and two 3.5" HDDs. LED indicators for power status and HDD activity, Support four half-size add-on cards.
-
Product
PCIe Digital I/O Board, 64 Optically Isolated I/O Channels, 5V-HS
APCIE-1564-5V-HS
-
32 digital inputs, 5 V, isolated16 interruptible inputs32 digital outputs, 5 V, isolated, 10 to 36 V, 500 mA/channelOptical isolation 1000 VWatchdog for resetting the outputs to "0" (when Power-On)Protection against fast transients, overvoltage, electrostatic discharge and high-frequency EMIInputs: voltage reversal, input filtersOutputs protected against short circuitOvertemperature and overvoltage protectionDiagnostic report in case of short circuits, overtemperature, voltage drop ...24 V power outputs with protection diodesShutdown logic when the external supply voltage drops below 5 V
-
Product
96-Ch Digital I/O PCI Card
PCI-1753
Isolated Digital I/O Card
Emulates mode 0 of 8255 PPIBuffered circuits for higher driving capacity than 8255Multiple-source interrupt handlingInterrupt output pin for simultaneously triggering external devices with the interruptOutput status read-back“Pattern match” and “Change of state” interrupt functions for critical I/O monitoringKeeps I/O setting and digital output values when hot system resetSupports dry contact and wet contactHigh-density 100-pin SCSI connector
-
Product
Enhanced 16 Differential I/O Multi-Mode Transceiver Channels
DF2
-
Function module DF2 (Enhanced Version) multi-mode transceivers with 16 programmable I/O channels. Differential transceivers increase resistance to noise by creating two complementary signals. These complementary signals produced on balanced lines double noise immunity by creating lower power requirements due to lower supply voltages.
-
Product
REM-11120, 4-Channel Thermocouple, 1-Channel Voltage, Temperature Input Module for Remote I/O
784750-01
Temperature Input Module
4-Channel Thermocouple, 1-Channel Voltage, Temperature Input Module for Remote I/O - The REM‑11120 is a temperature input module for remote I/O. Remote I/O systems are low-cost, modular systems for simple machine control and measurements. A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the REM‑11120 from a real-time controller such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low-cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high-speed or specialty measurements. The REM‑11120 also has an adjustable filter time for improved measurement quality and optional external cold junction compensation (CJC) or PT100 resistance temperature detector (RTD) measurements.
-
Product
16-Ch Digital Input EtherCAT Slice IO Module
AMAX-5052
Digital Input Module
Channels:16Digital Input;Dry Contact;Logic level 1: close to Iso.GND;Logic level 0: open;Wet Contact;Rated voltage: 24VDC;Logic level 1: 10~30 VDC;and -10~-30 VDC;Logic level 0: -3~3 VDCInput Delay:From logic level 0 to 1: 4ms;From logic level 1 to 0: 4msDigital Filter: 3ms
-
Product
Enhanced 16 Discrete/Switch I/O Channels (±80 V, 625 mA/Ch.)
DT5
-
The DT5 module (the enhanced version) features 16 independent, isolated, programmable channels that can be used for input voltage measurements (±80 V), or as a bi-directional current switch (up to 500 mA per channel). When programmed as a switch with the switch closed, both the current through the switch and the voltage across the switch can be monitored. These modules include diode clamping on each channel. Clamping is useful for inductive loads, such as relays and short circuit protection. Additional features of the DT5 (Enhanced Version) are listed below.
