LED
Semiconductor diode that emits narrow spectrum light by converting electric energy into electromagnetic radiation.
See Also: GaN
-
Product
S2 Penta Sensors
ULP-S2 PCI/V
LED Sensor
Optomistic Products’ best-selling Sensor, the ULP S2 Penta Sensor, is relied upon for its versatility in accommodating most LED color and intensity test applications. Implemented in a unique and customizable 2-Part solution, the S2 Penta Sensor is assembled with your choice of Fiber-Optic Probe, including for the test of densely-spaced LEDs, bright LEDs, dim or misaligned LEDs, right-angle LEDs, and more, including the popular “Trident” Fiber-Optic Probes to sequentially test 3 LEDs with a single Sensor.Operating temperature range: 0oC to 70oCPower consumption:Operates between +5 and 28 volts D.C., at 6mA max. Less than 4.75 volts is not recommendedVoltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsOutput Loads: ‘Int.’& ‘Color’- 2Kohms min., 100pF max.Output Pins: 4 gold-plated standard wire-wrap pins (0.025 in. sq.)Sensor Size: 0.560 in. dia x 1.38 in. longTypical response times: Typical response time: <10mS capture time; <100mS overall responsetime for color and intensity simultaneouslyFiber-Optic Probes: Can be paired with any Universal LightProbe Fiber-Optic Probe
-
Product
LED Color Sensor
Smart FINN Bright
-
LED applications have evolved from simple status indications to extremely bright lighting for commercial, industrial and military applications. The intensities of these bright LEDs are beyond the capability of the human eye to withstand, let alone be able to discriminate for color. Much like the human eye with sunglasses, we are able to shade our FINN sensors in order to provide accurate color and intensity measurements.
-
Product
LED Test Instruments
-
Photobiological Safety of Lamps and Lamp System and IEC TR62471-2(2009) Guidance on Manufacturing Requirements Relating to Non-laser Optical Radiation Safety have be published addressing hazard to human (mostly eye and skin), and are completely suitable to assess the optical radiation safety of non-laser sources, such as LED products, UV radiation in general lighting products and etc.
-
Product
Fuorescence LED Illumination System
pE-2
-
The pE-2 is a fluorescence LED illumination system which provides repeatable and controllable light with a choice of 20 different LED peaks. It is perfect for the researcher who has a specific set of tests to conduct. The user can specify a wavelength configuration matched to their particular fluorescence requirements. It is modular, allowing LED wavelengths to be exchanged as requirements vary or additional experiments are added. Manual control is via a remote control pod with instant on/off and intensity control from 0-100%. Additionally, the system is fully integrated under many imaging software packages.
-
Product
LED Driver Aging Rack
LEDRACK-100W192P
-
• Application range: LED driver and multi channel driver power aging. It has equipped with computer operation and monitor system. The working condition can be set by the computer, and the computer will record real time data to do statistical analysis. • The parameters of load can be set freely on the software, to monitor the real time voltage, current, and power etc • Load mode: CC, CV, CR, CP, and LED • Aging Control System includes: ON/OFF control signal output; Signal of relay switch control; K type thermocouple temperature acquisition • The channels are parallel connected under arbitrary load mode, which can allow product power expansion • The LED Driver Aging rack will design according to customer’s LED driver power and aging quantity per time • Automatic current switching function (optional) • AC power meter to measure modules, and test power input characteristics (optional) • Temperature monitoring function at product zone (optional) • PWM dimming and two sets of logic control signal function (optional)
-
Product
Optical Contact POF Ext Ø 1mm For VPC RCV Mini Power 510104123
AN396
LED Sensor
Optical contact probe for sensing LEDs.
-
Product
LED Phosphorescence Light Sources
SpectraLED
-
Innovative and affordable pulsed light source for phosphorescence measurements from deep UV to NIRThe SpectraLED is a novel light source designed specifically for the measurement of phosphorescence lifetimes. These phosphorescence sources are based on LED technology and the emission wavelengths range from the deep UV to the NIR.
-
Product
SMD LED Aging Tester
-
Shenzhen Chuangxin Instruments Co., Ltd.
LED life tester with 150 independent constant current to aging-life and color comparisons of 50pcs 5050 SMD LED and 100pcs 3528 SMD LED.
-
Product
High Power LED Aging Tester
LS600
-
• The standard LS600 has 1 Group which has 8 channels. That means LS600 can test 8 LEDs separately at one time. (Optional: it expand to 8 Groups which can test 64 LEDs separately at one time) • Aging Functions: Constant Current, Impact Pulse, On/Off Mode • Output current: 1~1000mA (Special Order Available) • Output voltage: 5V(Special Order Available) • Output frequency: 1~3000Hz, Duty Ratio: 1%-99% • Range of on-off circle: 0~9999h/59m/59s
-
Product
LED light sources
MLED4
-
Photocatalysis, ultraviolet analyzer biological genetic engineering, molecular genetics, medical and health, biological products, pharmaceutical research, health and epidemic prevention, dye chemical industry, petroleum chemical industry, textile industry, etc.
-
Product
LED Light Sources
-
LED light sources provide high power at a precise wavelength. A typical application for AvaLight-LED sources is fluorescence. They provide a long lifetime, short warm-up time, and high stability.
-
Product
LED 4 Flat Tester
48655
-
Hopkins Manufacturing Corporation
Quickly and easily confirm if your vehicle 4 flat connector wiring is properly installed and functional. Fits on your keychain to keep it handy! LEDs test left/right turn, brake and taillight.
-
Product
Built-in LED Gem Tester
-
Fuzhou Zhongtuo Optoelectronic Co.,Ltd
Gem Tester Refractive index is one of most important optical parameter. Gloss of gem can be estimated by the parameter.The kinds of gem can be precisely determined in accordance with the measured value of refractive index because every kind of gem has its inherent refractive. Besides, index of double refraction can be also measured. Through the parameter you can judge whether a gem is uniaxial or biaxial photopositive or photonegative.
-
Product
LED Driver (V4, V5, PWM, 18CH)
SLAMMO
-
When it comes to LED control, bigger IS better and the SLAMMO boasts class-leading capacity of up to 25Amps, 600W @24VDC (up to 450W in IP67 enclosures) / 300W at 12VDC. For constant current LEDs, the SLAMMO P can drive up to 96 luminaires equipped with PWM controlled CC drivers such as the Meanwell LDD series (350mA to 1.6A per LDD)
-
Product
PC Based Test Setup for LED Driver of LED
-
The tests are Performed as Prescribed in IS the Panel Carries out high voltage, open circuit and performance tests, one by one and provides indication of the Test results as PASS or FAIL lamp for high voltage test. It is very useful and handy in line testing on Mass production line as well as type Testing. Special fixture can be provided for the specific product. This avoids the connections & disconnections of the product for different tests. The total time for entire testing is less than 80 seconds. Micro controller based sequential timer maintains the sequence of operation and displays the test status. The entire system is housed in sturdy M.S cabinet with powder coating.
-
Product
Thermal Resistance Spectroradiometeric System for LED
TRS-1000
-
Thermal parameter is the key index to evaluate the quality of LED. Different temperature will have significant different effects on optical parameters, color parameters, electricity parameters and life of LED. Therefore, design and control of the thermal dissipation are the most important thing for the manufacturers and users. Referring to the relative international standard, TRS-1000 could conduct integration testing on optic, color, electricity and thermal, meanwhile record the changing curve of the parameters at real time.
-
Product
SparkFun LED Driver Breakout
LP55231
-
The SparkFun LP55231 LED Driver Breakout is a self-contained solution for developing and deploying the nine-channel I2C LED controller. Remarkably simple, the breakout is equipped primarily with just the LP55231 LED controller IC, plus three RGB LEDs. It also features pads and jumpers for replacing the onboard LEDs with external ones, and configuring the I2C bus, which allows you to daisy-chain up to four LP55231s. This breakout drives the LEDs using Pulse Width Modulation (PWM), so it is well-suited for variable intensity and color-mixing applications!
-
Product
LED Tester0.3m-2m Integrating Sphere
CX-8000
-
Shenzhen Chuangxin Instruments Co., Ltd.
Measure Luminous Flux, Luminous efficacy, radiant power, Spectral Power Distribution, Chromaticity Coordinate, Correlated Color Temperature, Peak Wavelength, Dominant Wavelength, Spectral Half Width, Color Rendering Index, Colorimetric Purity, red ratio, Standard deviation of color matching(SDCM), voltage, current, power, power factor, harmonics, and etc. It meets the requirements of CIE standards.
-
Product
PicoBuck LED Driver
-
The PicoBuck LED Driver is an economical and easy to use driver that will allow you to control and blend three different LEDs on three different channels. By default, each channel is driven at 330mA; that current can be reduced by either presenting an analog voltage or a PWM signal to the board. Version 12 of the board adds a solderable jumper that can be closed to increase the maximum current to 660mA. The new voltage regulator also increased the voltage rating on the various components on the board, allowing it to be used up to the full 36V rating of the AL8860 part.
-
Product
GLP2 Luminaries/LED Tester
-
Safety, function, programming and controlling of LED Lighting from one device. Dramatically reduces set up and test times. Ease of use eliminates errors.
-
Product
LED Optical Aging Test Instrument
LEDLM-80PL
-
LEDLM-80PL LED Lumen Maintenance and Aging Life Test System is designed according to standards of IES-LM-80, IES-LM-82, TM-21 and GB2312-80, and the software is developed base on Arrhenius model. LED has the features of long life, but with the different working condition and drive current, its life will be different, but generally the life will be around 50K hours. Differ from the traditional lightsource, LED light will decay gradually rather than extinguish instantly, so in the standard of LM-80, it introduces L70, L50 and etc.
-
Product
LED Driver Automatic Test System
ATE-2
-
•This system includes 2 groups (left and right); the 2 groups can work in turn, so that to improve the work efficiency. For example, if the left is on working, then the right can make wire connection. •It can test 4 LED drivers input and output at one time. •The equipment can connect with electronic load and LED load, the two difference loads can be fast switch under the control of computer. •Enable to print out the series number and parameters of sub-quality products by working with a micro-printer, •Enable to achieve the bar-code record function by working with a bar-code scanner. •The test report can be saved as Excel file for consult, statistic and analysis purpose. •Good software interface to freely choose the difference parameters combination, so that to meet different demands. All the parameters can set limit, and with the quality analysis function.
-
Product
LED Spot Type UV Curing Systems
AICURE UJ30/35
-
Panasonic Industrial Devices Sales Company of America
The compact UJ30/35 UV Curing System can be equipped with up to four individually controlled LED heads. Different types of UV-LED heads are available with an irradiation wavelength of either 365nm, 385nm or 405nm. The Controller allows for external contact inputs or PLCs for automated applications.
-
Product
S2 Spectra Sensors
ULP-S2 WBI/V
LED Sensor
The ULP S2 Spectra Sensor tests for LED intensity, and for any color in the visual spectrum, plus white. The S2 Spectra Sensor is well-suited for the test of “boundary” color LEDs, as it can unambiguously and repeatedly distinguish between not only adjacent visual colors such as green and yellow, but it can determine different hues of the same color such as yellow and amber, regardless of LED intensity. Implemented in a unique and customizable 2-Part solution, the S2 Spectra Sensor is assembled with your choice of Fiber-Optic Probe, including for the test of densely-spaced LEDs, bright LEDs, dim or misaligned LEDs, right-angle LEDs, and more, including the popular “Trident” Fiber-Optic Probes to sequentially test 3 LEDs with a single Sensor.Operating temperature range: 0oC to 70oCPower consumption: Operates between +5 and 28 volts D.C., at 6mA max. Less than 4.75 volts is not recommendedVoltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsOutput Pins: 4 gold-plated standard wire-wrap pins (0.025 in. sq.)Output Loads: ‘Int.’& ‘Color’- 2Kohms min., 100pF max.Sensor Size: 0.560 in. dia x 1.38 in. long.Typical response time: Typical response time: <10mS capture time; <100mS overall response timefor color and intensity simultaneouslyFiber-Optic Probes: Can be paired with any Universal LightProbe Fiber-Optic Probe
-
Product
12V Circuit Tester With LED Polarity Indicator
1658
-
Peaceful Thriving Enterprise Co Ltd
Checks open or short circuits on 12V automotive computer circuits and all primary automotive electrical circuits. Safely tests standard primary automotive circuits and on-board computer controlled electrical system without damaging the micro-processor.
-
Product
High-Speed/LED Sensing Fiber Sensor
FX2
-
Panasonic Industrial Devices Sales Company of America
The FX2 Series Fiber Sensor has multiple amplifiers. The FX-A3R has a 15us high speed response time and is suitable for detecting small objects or objects traveling at high speed. The FX2-A3R-LED is an LED sensing type amplifier, which can detect weak lighting from LEDs.
-
Product
LED Power Driver Test System
Chroma C8000
-
Chroma Systems Solutions, Inc.
The Chroma 8491 ATS is equipped with optimized standard test items for LED driver testing (lighting & TV backlight). The user is only required to define the test conditions and specifications for the standard test items to perform the test.
-
Product
LED based light source
iQ-LED
-
Image Engineering GmbH & Co. KG
The most flexible, 22 channel, LED based light source is the heart of all adaptive lighting productsCreate your own light by adjusting the 22 channels to your needs. You can simulate standard light sources, reconstruct the daylight distribution from dawn till dusk, create patches of a high saturated color chart, or reconstruct the spectral distribution of a measured light source. By using the individual channels you can even measure the spectral sensitivities of a camera.
-
Product
3 Digit LED Voltmeter
SP 300
-
The SP 300 is a 3 digit LED voltmeter with 9mm (0.36") digit height. It features 200mV d.c. full scale reading, auto-zero and auto-polarity. The meter plugs directly into an 8-way SIL socket and can be fitted into a panel via the fixing clip. Splashproof protection to IP65 is achieved by fitting the seal supplied.
-
Product
S2 Unicolor Sensors
ULP-S2 SCI/V
LED Sensor
The Universal LightProbe S2 Unicolor Sensor is designed for the intensity test of any single one of the five main LED colors (blue, green, yellow, orange, and red) plus white and Infrared (700nm to 1,000nm). Implemented in a unique and customizable 2-Part solution, the S2 Unicolor Sensor is assembled with your choice of Fiber-Optic Probe, including for the test of densely-spaced LEDs, bright LEDs, dim or misaligned LEDs, right-angle LEDs, and more, including the popular “Trident” Fiber-Optic Probes to sequentially test 3 LEDs with a single Sensor.Operating temperature range: 0oC to 70oCPower consumption: Operates between +5 and 28 volts D.C., at 6mA max. Less than 4.75 volts is not recommendedVoltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsSignal Output Loads: 20 mA max. Non-inductive.Output Pins: 3 gold-plated standard wire-wrap pins (0.025 in. sq.)Sensor Size: 0.560 in. dia x 1.38 in. longOperating Temperature Range: 0hC to 70hCTypical response times:<10mS capture time; 65mS overall response time; intensity output of correct color only.Fiber-Optic Probes: Can utilize any Universal LightProbe Fiber-Optic Probe
