Fibre Channel
Data transfer interface with speeds up to 2 Gigabit per second that maps to common transport protocols, i.e. IP and SCSI.
-
product
Dual Channel MIL-STD-1553 BC/RT/MT cPCI Intelligent Module
DP-cPCI-5664
The DP-cPCI-5664 provides new level of performance and flexibility for MIL-STD-1553B notice 2 in a Compact PCI form factor. It has full intelligent interfacing between a cPCI bus and one / two independent dual redundant MIL-STD-1553B data buses. The 1553B bus functions are fully controlled by a DSP processor. Software controls the operation of the channel as either a 1553 Bus Controller (BC), Remote Terminal (RT), or Bus Monitor (MT).
-
product
8 Channel Sample & Hold and Signal Conditioning Board for Group3
All channels provide for voltage division ahead of transient suppression before going into the S&H ICs. Channels that are sampled and held use a common sample and hold pulse that samples while high and holds while low. Jumpers on each S&H chip allow buffering of analog signals where sample and holds are not required. An advantage to the buffers is that it provides a high input impedance for high impedance voltage dividers.
-
product
HD Oscilloscope, 2GHz, 10 GS/s ESR, 4 CH, 500 Mpts/Ch (Single Channel), 12-Bit HD
T3DSO4204L-HD
2GHz, 10 GS/s ESR, 4 CH, 500 Mpts/Ch (Single Channel), 12-Bit HD Low Profile Oscilloscope.
-
product
Channel Emulator
Qosmotec Software Solutions GmbH
Knowledge about channel models is not necessary to run tests with the QPER Channel Emulator. It applies the visualised virtual drive test concept, which is also used in the handover tester, to a fully fledged channel emulator: The tester outlines the network layout on the screen and defines a drive test route on the map. While running a simulated drive test, all channel effects are automatically calculated by QPER and applied to the channel emulation hardware.
-
product
Infiniium UXR-Series Oscilloscope: 50 GHz, 4 Channels
UXR0504A
The UXR0504A is the 50 GHz, 4 channel, Infiniium UXR-Series real-time oscilloscope
-
product
PXI MUX 2 Banks of 32 Channel 2 Pole
40-610-022-2/32/2
This series of high density multiplexer modules feature a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector. Inter-bank linking relays allow multiplexer size to be increased in multiples of in multiples of three by joining the common terminals of adjacent banks. Closing one linking switch produces a 6-channel multiplexer, closing all linking switches produces an 54-channel multiplexer
-
product
130/180 MS/s Dual Channel PXI Express Digitizer for Frequencies up to 175 MHz
PXIe-1803
This 130/180 MS/s Dual Channel PXI Express digitizer provides the best speed and performance available for input frequencies up to 175 MHz.With exceptional signal integrity, high density and modularity, and channel synchronization options, this new digitizer provides massive functionality in a compact form factor.Key features include:Dual 14/16-bit digitizer configurable as separate or fully synchronized channelsWaveform bandwidths of 65-175 MHz (typical)64M words of waveform memory per channelExternal clock input for synchronization up to 180 MHz250 μV Measurement AccuracyNoise Floor and RelativeAccuracy as Precise as 0.006%
-
product
4 Channels DC Power Data Acquisition Device
NuDC-4U
NuDC-4U is an innovative product that provides better solution for power probing. Common DC power statistics including voltage, ampere and even the watt can be read instantly via NuDC-4U. Moreover, up to 4 sets of individual powers can be monitored simultaneously and the LCD screen can also display the maximum and minimum value of the current power during the test.
-
product
Triple Channels DC power supply
IT6300 Series
IT6300 series is high-performance programmable triple channels DC power supply, each output voltage and current can be setfrom0 tomaximum rated output.This series provides series connection, parallelconnectionand synchronous functions ofchannel, which offer multi-purpose solutions forcustomerstest.IT6300 seriesis with high resolution1mV / 1mAand remote sense function, which make the test more accurate. Withbuilt-in standard USB / RS232 / GPIB communication interface,IT6300 seriesgreatly enhance the communication speed, and customersalsocanadjust the digital step value byusing the cursorto to facilitate the operation.
-
product
HandyScope HS4: 50 MS/s 100MHz BW, 4 Channel, USB Digital Storage Oscilloscope, Spectrum Analyzer, Voltmeter, Transient Recorder
HS4-50
HandyScope 4: 50 MHz, 4 Channel, USB Multi-Instrument (DSO, Spectrum Analyzer, Voltmeter, Transient Recorder). The Handyscope-4 is the successor of the popular Handyscope HS3. Built for customers that want to extend their measuring capabilities even further, this powerful computer controlled measuring instrument now features four input channels.
-
product
Infiniium UXR-Series Oscilloscope: 70 GHz, 4 Channels
UXR0704A
The UXR0704A is the 70 GHz, 4 channel, Infiniium UXR-Series real-time oscilloscope
-
product
Single Channel Universal Power Meter
8541C
The Spanawave/Giga-tronics 8541C Single Channel Universal Power Meter combines accuracy, speed, range and measurement capability.
-
product
Handheld Single Channel Digital Oscilloscope 20MHZ-100MHZ
HDS-N
Shenzhen Chuangxin Instruments Co., Ltd.
- 2 in 1 (DSO + Multimeter)- Auto-scale function- 20 automatic measurements- Bandwidth : 20MHz - 100MHz- USB data transmission supported- Waveform record and replay- Multimeter newly supported SCPI- Rechargeable Li-ion battery (6 hours' backup)
-
product
Dual Channel Temperature/Relative Humidity-40 to +85C/0 to100% RH
TGIS-1580
This model is battery powered and measures both temperature and humidity using built-in sensors, providing cost effective environmental monitoring ideal for inaccessible locations.
-
product
Conduction Cooled Interface Board Supporting up to 5 Multi Function Channels
EXC-1553PMC/Px(S) / EXC-1553ccPMC/Px(S)
MIL-STD-1553, conduction cooled, interface board. Supports up to 4 multi function channels.The EXC-1553PMC/Px(S) and EXC-1553ccPMC/Px(S) are multi-channel (up to four) MIL-STD-1553 interface boards for PCI Mezzanine Card compatible computers.Multi Function:Each channel operates simultaneously as a Bus controller and/or multiple (up to 32) Remote Terminals, or as a Triggerable Bus Monitor. In addition, error injection (BC and RT modes) and error detection (all modes) are supported on each channel.Single Function:Each channel operates either as a Bus Controller, Remote Terminal, or Bus Monitor.NOTE: PxS is NOT compatible to the MCH family of cards.The EXC-1553PMC/Px(S) and EXC-1553ccPMC/Px(S) are supplied with C drivers, including source code, and Merlin+ Windows software.
-
product
CAN/FlexRay/Differential Bus PXI Fault Insertion Switch - 4 Channel
40-200-004
Each channel can support up to 0.3A and is rated to handle up to 100V between the wire pairs. The wire pairs have controlled transmission line impedance suited to most differential pair signaling systems, including fast CAN Bus interfaces and RS232. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
product
Digital I/O Board, 32 Isolated I/O Channels, 24V +special EEPROM & TTL IO Port
APCI-1500-PULS
PCI interface to the 32-bit data bus Connector compatible to PA 1500 Connector and software compatible to CPCI-1500 16 isolated input channels, 24 V, including 14 interruptible 3 software-programmable counters/ timers 16 isolated output channels, 10 to 36 V, output current 500 mA Timer-programmable watchdog for the reset of the outputs"-PULS" version has a special EEPROM and a TTL IO port added at end of cardDiagnostic report through status register in case of short-circuit, overtemperature, voltage drop or watchdog Interrupt triggered through watchdog, timer, error One ground line for all inputs and one ground line for all outputs
-
product
PCIe 16 Bit Arbitrary Waveform Generator - up to 40 MS/s on 4 Channels
M2P.6536-X4
The M2p.65xx series offers different versions of arbitrary waveform generators for PCI Express with a maximum output rate of 125 MS/s. These boards allow to generate freely definable waveforms on several channels synchronously. With one of the synchronization options the setup of synchronous multi channel systems is possible as well as the combination of arbitrary waveform generator with digitizers of the M2p product family. The 512 MSample on-board memory can be used as arbitrary waveform storage or as a FIFO buffer continuously stream data via the PCIe interface. Importantly, the high-resolution 16-bit DACs deliver four times the resolution than AWGs using older 14-bit technology.
-
product
Sixteen Channel, 12-Bit Analog Input Card
PCI-AI12-16(A)
Model PCI-AI12-16 is a multifunction, high-speed, analog-to-digital converter board for use in PCI-Bus computers. It accepts up to 16 single-ended or eight differential inputs. The board uses a low-noise, multilayer printed circuit board. Inputs are protected against overvoltage conditions up to ±35 volts and typically survive static discharges beyond 4000 volts.
-
product
WaveRunner Oscilloscope, 2.5 GHz Bandwidth, 4+16 Input Channels, 20 GS/s on 2 Ch Sample Rate
WaveRunner 9254-MS
2.5 GHz, 20 GS/s, 4ch, 16 Mpts/Ch Mixed Signal Oscilloscope with 15.4" Capacitive Display.
-
product
Oscilloscope 110 GHz, 2 Channels
UXR1102B
The UXR1102B is the 110 GHz, 2 Channel, UXR-Series Real-Time Infiniium Oscilloscope.
-
product
NI-6581, 100 MHz, 54 Single-Ended-Channel Digital I/O Adapter Module
780565-01
100 MHz, 54 Single-Ended-Channel Digital I/O Adapter Module for FlexRIO—The NI-6581 is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO, creates a digital instrument for interfacing with 54 single-ended digital pins. You can use the NI-6581 to do real-time interfacing of standard protocols and implement customized protocols. The NI-6581 can operate sample digital waveforms at up to 100 MHz. It includes support for common transistor-to-transistor logic (TTL) voltage levels, or other voltage references can be sourced externally using a front panel connector.
-
product
Oscilloscope, 200 MHz, 4 Input Channels, 2 GS/s interleaved, 200 Mpts - interleaved
T3DSO2204A
200 MHz, 2 GS/s per Ch, 2 GS/s interleaved, 4 CH, 200 Mpts/Ch DSO with 10.1" Color Display.
-
product
Mixed Signal Oscilloscope - 350 MHz, 4 Analog Plus 16 Digital Channels
MSOX4034A
350 MHz4 analog plus 16 digital channels Easily view signals on the large 12.1-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering Capture more data with 4 Mpts memory and standard segmented memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add bandwidth, dual-ch 20 MHz arbitrary Wave Gen, 3-digit DVM, serial trigger and analysis & mask testing at any time
-
product
Mixed Signal Oscilloscope: 16 GHz, 4 Analog Plus 16 Digital Channels
MSOV164A
16 GHz analog bandwidth (upgradable)4 analog plus 16 digital channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with the low noise floor (1.32 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Access the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
-
product
Enhanced 16 Differential I/O Multi-Mode Transceiver Channels
DF2
Function module DF2 (Enhanced Version) multi-mode transceivers with 16 programmable I/O channels. Differential transceivers increase resistance to noise by creating two complementary signals. These complementary signals produced on balanced lines double noise immunity by creating lower power requirements due to lower supply voltages.
-
product
Infiniium S-Series High-Definition Oscilloscope: 4 GHz, 4 Analog Channels
DSOS404A
4 GHz bandwidth (upgradable)4 analog channels Capture a longer signal trace with 20 GSa/s max sample rate and 100 Mpts/channel of standard memory Get superior signal integrity with system ENOB of 7.2 bits and 10-bit analog-to-digital converter (ADC)Gain increased usability with the multi-touch supported 15 inch capacitive touch screen and solid state drive for fast boot and reliability Improve your testing with a wide range of protocol, compliance, and analysis software
-
product
sbRIO-9234 , Non-Enclosed, 4-Channel, 51.2 kS/s/channel, ±5 V, C Series Sound and Vibration Input Module
782718-01
Non-Enclosed, 4-Channel, 51.2 kS/s/channel, ±5 V, C Series Sound and Vibration Input Module - The sbRIO‑9234 can measure signals from integrated electronic piezoelectric (IEPE) and non‑IEPE sensors such as accelerometers, tachometers, and proximity probes. The sbRIO‑9234 is also compatible with smart TEDS sensors. The sbRIO‑9234 delivers a wide dynamic range and incorporates software-selectable AC/DC coupling and IEPE signal conditioning. The input channels simultaneously measure signals. Each channel also has built-in anti‑aliasing filters that automatically adjust to your sample rate. When used with NI software, this module provides processing functionality for condition monitoring such as frequency analysis and order tracking. Non-enclosed modules are designed for OEM applications.
-
product
64 Channel Form A High Power Relay
DP-cPCI-4305
DP-cPCI-4305 is a 64-channel 1 Form A, high power relay module. This general purpose relay can be used for high power switching applications. Applications for this module include power routing, automatic test equipment, relay output for soft PLCs and bounce-free switching.
-
product
80 Channel Relay Switch
DP-VXI-4503
DP-VXI-4503 is a 80 channel, one Form C (SPDT) relay switch designed as a C size VXI module. This high density switch module is designed with a register based interface occupying only one VXI slot. This module uses two Form ‘C’ relay switches. Out of the two contacts in each relay, one is used to provide the status of the relay through read back and the other is used for switching purpose.The user can write the command for the selected channels on to the primary latch of the FPGA section. Readback is available to confirm the selected commands. On command, the data from the primary latch is transferred to the secondary latch. The relay driver section provides the necessary drive to switch ON the relays. The buffers in this section drive the relay coils.This module features a back plane trigger for VXI triggered operation. On receipt of the back plane trigger the programmed relays will be energised/de-energised. Alternatively, software trigger can be used.
