-
Product
IEC60884 Plug Power Cord Bending Test Machine
CX-YB06
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884 plug power cord bending test machineThe power cord bending tester is used to bend (bend) the power cords of non-reconnectable plugs and household appliances and similar appliances.It complies with UL817, VDE0620, IEC60884-2006 Figure 21, and other standard requirements.The device can preset the number of tests (up to 999999 times), the test is automatically carried out, and when the te
-
Product
Functional Test Fixtures
-
Businesses rely on Circuit Check’s functional test fixture expertise. Functional test typically applies full operational power to a loaded printed circuit board in order to determine if the PCBA performs functions as designed. This type of test often involves custom built test equipment and custom test fixturing. Circuit Check supports all forms of functional test strategies.
-
Product
Pressure Test Points
Minimess
-
Minimess test points offer a uniquely simple method of accessing low or high pressure systems for the purpose of pressure testing, oil sampling or gas charging. Developed by Hydrotechnik more than 50 years ago, they are found worldwide in hydraulic, process and gas systems. These pressure test points offer the most advanced sealing system available with working pressures up to 630 bar.
-
Product
Test Chambers
Anechoic
-
Free Field Test Chamber for sound pressure level measurement, sound power level determination, acoustic research and audio measurement applications
-
Product
Walk in chamber for Complex Salt Spray Test (Temperature controllable)
-
Guangdong Bell Experiment Equipment Co.,Ltd
Walk in chamber for Complex Salt Spray Test Relevant standards requirement1. Test Object: battery pack andsystem.2. Refer GB/T4 part 5.5.2 test method, test according to GT/T2423.17 test conditions.3. The salt solution was made up with sodium chloride (chemically pure and analytically pure) and distilled or deionized water，Its concentration is (5 + 1)% (mass fraction).4. (35 ± 2) ℃, the measured pH value is between 6.5-7.2.5. Placed the test objects in the salt spray chamber for cycling test. Each cycling duration for 24h. Spray salt solution to the test object for 8 hours under the temperature of (35± 2) ℃ , remain for 16 hours. Between the forth and the fifth hour in one cycles should be according to test requirement in GB/T 28046.1-2011, test mode with 3.2.6. Total 6 cycles testing.7. Salt spray test is not necessary for the test objects being installed in passenger, luggage or cargo compartments.
-
Product
Test Lead Holders
-
Test lead holders offer a great way to organize and store your test leads. With the various types of cable and test leads available, Pomona offers many options to organize your test leads.
-
-
Product
Fiber Optics Test Data Management, Remote & Cloud Applications
Fiberizer™
-
Software solutions for remote optical testing and data post-processing for managing test data and generating reports that integrate OTDR, link map, GPS coordinates, OLTS (loss and ORL), connector inspection, and captured images. Available for Window PC, Mobile Apps (Android, iPhone and iPad devices) and Fiberizer Cloud.
-
Product
Test & Measurement
-
High-quality connection solutions for precise measuring, testing and examination. Whether low or medium voltage range, whether precise test runs or preventive measuring and testing: With an extensive portfolio of specific components and cables, Stäubli always ensures perfect and reliable contact between the measuring instrument and the points, objects and systems to be tested. In addition, we are a proven partner of leading manufacturers of measuring instruments in this field, for example for equipping them with high-quality sockets. Every product meets all quality and safety standards.
-
Product
Test Sets For Motor & Generator Industries
-
Test Sets For Motor & Generator Industries are designed for no-load loss as well as heat run testing. They are ideal for offering clean power with precise regulation as well as voltage control. These sets are designed when there is no need of frequency conversion. With variable-frequency drive of these sets, they are used to select any output frequency from 50 Hz to 60 Hz. in addition to this, for larger requirements, from 50-to-200 Hz, this has been used as one of the most economical testing sets.
-
Product
Easy-to-assemble and Collapsible RF Test Enclosure With Fabric Shielding, ≥ 90 DB Isolation, 300 MHz - 18 GHz
dbTENT
-
The dbTENT is an easy-to-assemble, store and transport high-performance RF test enclosure. Whether you need to make measurements in the field or in the lab, the dbTENT provides superior 90 dB of isolation over a wide frequency range thanks to its patented double layer conductive fabric design. Featuring an interchangeable customisable I/O panel, the dbTENT meets all your needs for non-permanent isolated testing. With a setup time of only minutes, the dbTENT will get you ready for testing instantly in a wide variety of environments.
-
Product
Pneumatic and Hydraulic Characteristics Test
-
Pneumatic and hydraulic testing is performed to demonstrate operating pressure, pressure drop, volume and flow parameters, as well as performance characteristics, of fluid system components and assemblies.
-
Product
Cell Site Test / BBU
-
VIAVI mobile base station test solutions are the industry’s most comprehensive and cost effective for installation, commissioning, and maintenance.
-
Product
Repeated Charge Discharge Test Set
-
The IS 13341 : 1992 has laid down the requirements for Ageing Test, Self-Healing Test and Destruction Test on Shunt Capacitors of the self healing type for AC Power Systems. The Ageing Test is to be performed at a specified voltage of 1.25 times the rated voltage for 750 hours. The test is to be followed with a repeated discharge cycle test which involves charging of the capacitor to a DC voltage and discharge of the same through an Inductance. Sivananda Electronics has developed this equipment for the benefit of capacitor manufacturers, for the first time in India.
-
Product
Universal relay test set and commissioning tool
CMC 356
-
The CMC 356 is the universal solution for testing all generations and types of protection relays. Its powerful six current sources (three-phase mode: up to 64 A / 860 VA per channel) with a great dynamic range, make the unit capable of testing even high-burden electromechanical relays with very high power demands.
-
Product
RSP-2T Test System Interface Probe
RSP-2T
-
Current Rating (Amps): 5Average Probe Resistance (mOhm): 20Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 167Full Travel (mm): 4.24Recommended Travel (mil): 79Recommended Travel (mm): 2.00
-
Product
MIPI Receiver Test Solution
M8085A
-
The M8085A is a software plug-in for M8070A Bit Error Ratio Test system software within the M8000 series of BER test solutions. The M8085A software plug-in controls either the M8190A or the M8195A Arbitrary Waveform Generators to create C-PHY or D-PHY standard compliant test signals. In addition it provides routines for calibration of all signal parameters and for all tests specified in the applicable Conformance Test Suite. Together with the additional available DUT control interface it is possible to read the BER of the receiver under test from the M8070A software and display the BER dependency from test parameters within the M8070A user interface.
-
Product
Additional Test & Measurement Hardware
-
Additional Test & Measurement Hardware by electro-PJP
-
Product
Test Charts
iQ charts
-
Image Engineering GmbH & Co. KG
The basis of our test chart portfolio are the ESSER TEST CHARTS owned by Image Engineering and known worldwide for their high quality which we continually improve. Included in the extensive program are HDTV charts for broadcast, multipurpose charts as well as the UTT chart (Universal Test Target), the leading system for the standardized digitalization of archives, which is already being used by the Metropolitan Museum in New York.
-
Product
Functional Test Fixtures
-
EMC Technologies designs and manufactures discretely wired and wireless functional test fixtures used for performance verification of PCBs and Electronic Assemblies. Commercial applications have included work in support of many industries including: satellite TV, computer servers, medical, networking, and telecommunication.
-
Product
LOADED BOARD TEST PROBES
SERIES-70
-
ElectricalMAXIMUM CURRENT: 5 amps continuousat working travel, non-inductiveRESISTANCE: At 35mA test current70 18 mOhms mean73 60 mOhms mean74 40 mOhms meanMaterials and FinishesPLUNGER: Heat treated beryllium copperor steel hardened to 55-60RC70 24Kt gold plated over nickel73 24Kt gold plated over nickel74 Rhodium plated over nickelBARREL: Nickel silver70 24Kt gold plated ID and OD over nickel73 No Finish74 24Kt gold plated ID and OD over nickel
-
Product
Refrigerator Freezing Tester M Load Test Package
CX-MP
-
Shenzhen Chuangxin Instruments Co., Ltd.
The freezing load test package is made according to GB/T8059.2 GB/T8059.4, and we can also make the package in different standard according to different requirement.
-
Product
Ozone Test Chamber
-
Wewon Environmental Chambers Co, Ltd.
provide an effective solution to the testing of products for resistance against ozone degradation in a controlled environment. These test chambers function as static tensile test chambers as well as Rubber Test Chamber and are often used for studying static tensile deformation of various manufactured goods in the presence of ozone.
-
Product
Tweezers Contacts Test Fixture
16334A
-
Perform impedance evaluation on a minimum SMD size of 1.6(L) x 0.8(W) [mm]
-
Product
Test System for Detecting Exact PCB Short Circuit Locations
QT25
-
Qmax Test Technologies Pvt. Ltd.
QT25 employs a unique method to detect exact PCB shorts circuit locations and pin down the shorted components and tracks. It is designed in such a manner that it precisely detects exact short circuit locations across VCC - GND or a shorted component connected across a Bus or hair-line shorts between PCB tracks, Which is highly impossible to detect using conventional tools especially when they are connected parallel in circuit. It can also be used in measuring the contact resistance of switches and relays in its milli-ohm mode as a value add.
-
Product
Scienlab Battery Test System – Pack Level
SL1700A Series
-
Keysight’s SL1700A Scienlab Battery Test System – Pack Level Series allows to realistically emulate the environment of the future battery pack application in order to test the high-power battery pack comprehensively and improve its functions and safety. The growing demand of e-mobility increase the need of vast battery test labs for EV battery development. Keysight developed the SL1700A Series to accelerate the development and validation of batteries. It offers a voltage range of up to 1500 V and power options between 90 and 270 kW. The new high-voltage SiC (silicon carbide) technology provides a high energy efficiency on a small footprint and helps to minimize your operating costs.
-
Product
Test Socket
-
Our test sockets are made for high performance and are of top quality, to guarantee a smooth, effortless process. We believe in providing our partners and customers with effective and intelligent solutions that they can apply with ease. Choose the solutions of TTS Group cater to the needs of detailed and complex systems.
-
Product
ARINC825 (CAN Bus) Test & Simulation Module for VME With 4, 6 Or 8 CAN Bus Nodes
AVC825-x
-
ARINC825 (CAN bus) Test & Simulation Module for VME with 4, 6 or 8 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The AVC825-x VME card can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
Product
Test Circuit
-
Before charging the battery, it is essential to know the state of charge. It also often be performed electrical and electronic measurements in cars. To meet this demand, FERVE has the widest range of small testers market. These devices work directly on the battery and its variety of size allows it to fit any space, giving them an additional attraction that binds to the latest technology and the highest quality of their electronic components.
-
Product
Electrical Measurements Test
-
The tests are performed to measure and collect data from electrical and electronic parts using various measurement methods including, but not limited, to the following: capacitance, resistance, winding resistance, insulation resistance, magnetic permeability, power input, and quality factor Q.
