Evaluation Boards
-
Product
Evaluation boards
-
iSYSTEM evaluation and development systems are optimized for evaluation of the featuring microcontroller whether it fits the project requirements or for the development of the target application while the hardware is still in the design stage. Our systems are distinguished by high speed debug and trace connection to experience the full microcontroller capabilities.
-
Product
Universal Development Board For The Plug-in Module PCAN-MicroMod FD
PCAN MicroMod FD Evaluation Board
-
The PCAN-MicroMod FD Evaluation Board is a development board for the PCAN-MicroMod FD and enables the design and development of your own circuits with CAN connection and I/O functionality. It can also be used for training purposes for CAN and CAN FD structures. The user can access the resources of the attached PCAN-MicroMod FD via taps, screw terminals, switches and potentiometers and test configurations or test circuits.
-
Product
10 Gb/s SFP/SFP+ Evaluation Board
EV-SFP-171
-
The purpose of this SFP+ evaluation board is to provide the designer with a convenient means for evaluating SFP+ fiber optic transceiver such as 10 Gb/s(up to 16 Gb/s) SFP/SFP+ transceiver compliant with ANSI Fibre Channel FC‐PI‐5 for high speed electrical and optical specifications. This board provides SMA connectors for high speed TX and RX signals. The low speed control signals such as Tx_Fault, Rx_LOS and Rate_Selects can be controlled by using on board switches and test points. A connector for 2 wire serial interface to the module is also provided.
-
Product
MPU 9DOF Click
64219
-
Parallax speeds the process of Propeller 2 development through our partnership with MikroE, who has created a family of 850+ Clicks for most I/O functions you may envision. For each of the Click boards stocked by Parallax, you will find a documented Spin 2 code example on our Propeller GitHub Object Exchange. Connect your Click boards to the Propeller 2 Evaluation Board or P2-EC Edge Breakout Breadboard using the #64008 P2 to MikroBus Click Adapter.
-
Product
PCI Evaluation Board
BCM91250E
-
The BCM91250E is a full-length PCI evaluation board with the SiByte® BCM1250 dual-processor System on a Chip. The board is designed for software development and for developing PCI applications that require high-performance processors.
-
Product
SparkFun IR Thermometer Evaluation Board
MLX90614
-
This is an evaluation board for the MLX90614 IR Thermometer. The sensor is connected to an ATmega328 running at 3.3V with a STK500 (Arduino) 8MHz bootloader. Code can be loaded through the FTDI basic interface and the Arduino environment.
-
Product
Proximity 3 Click
64211
-
Parallax speeds the process of Propeller 2 development through our partnership with MikroE, who has created a family of 850+ Clicks for most I/O functions you may envision. For each of the Click boards stocked by Parallax, you will find a documented Spin 2 code example on our Propeller GitHub Object Exchange. Connect your Click boards to the Propeller 2 Evaluation Board or P2-EC Edge Breakout Breadboard using the #64008 P2 to MikroBus Click Adapter. Proximity 3 click is an intelligent proximity and light sensing device, which features the VCNL4200 sensor from Vishay – high sensitivity long distance proximity sensor (PS), ambient light sensor (ALS) and 940 nm IRED, all in one small package.
-
Product
Linux-based Development Platform For The GridARM™ ΜController
PEAK gridARM Evaluation Board
-
The ARM7 microcontroller gridARM™ was developed by Grid Connect® as a system on a chip solution (SoC) for the implementation of embedded applications with a focus on industrial communication. The Evaluation Board PEAK-gridARM is a Linux-based development platform for the gridARM™ microcontroller. It has connections for Gigabit Ethernet, high-speed CAN, USB 2.0, RS-232, SPI and I²C. The digital and analog inputs of the evaluation board can be manipulated with buttons and potentiometers. The states of the microcontroller, the supply and the message traffic are displayed via LEDs. A board support package for Linux enables access to the hardware resources of the PEAK-gridARM evaluation board.
-
Product
4X14 Gb/s QSFP/QSFP+ Evaluation Board
EV-QSFP-174
-
The EV‐QSFP‐174 QSFP/QSFP+ Host Test Board comes complete with Windows based software (Windows XP & above) to enable intuitive memory map programming and testing, controlled via a mini B USB port. It is designed to simulate an ideal environment for QSFP/QSFP+ transceiver module testing, characterization and manufacturing test. Its high speed properties make the host board as electrically transparent as possible, allowing for a more accurate assessment of the module’s performance.
-
Product
Evaluation Board
emPower
-
SEGGER Microcontroller GmbH & Co. KG
The emPower eval board provides a comprehensive set of SEGGER's middleware products, accelerating the start of any embedded project. SEGGER's embOS real-time operating system is at the heart of the evaluation. Furthermore, evaluation versions of the file system emFile, graphics library emWin, emUSB Host & Device, and TCP/IP stack embOS/IP (including web server demo) enable full use of the available emPower peripherals. emPower also features a J-Link OB, an on-board version of SEGGER's market-leading debug probe J-Link, which includes drag & drop programming and COM-Port support. There are three expansion interfaces to easily connect additional modules. Each connector provides I2C, SPI, UART, GPIO/timer, analog input and power. A display adapter connector enables the connection of small TFT displays. The emPower board is powered by USB only. Current consumption drawn strongly depends on the application and connected peripherals. Idle consumption is approx. 85 mA.
-
Product
PCI Evaluation Board
BCM91125E
-
The BCM91125E is a full-length PCI evaluation board with the SiByte® BCM1125H MIPS processor System on a Chip (SoC). The board is designed for software development and developing PCI applications, which require high-performance processors. The BCM91125E can be plugged into a PCI slot in any PC, workstation or server, or can be used as a stand-alone device.
-
Product
Air Quality Click
64202
-
Parallax speeds the process of Propeller 2 development through our partnership with MikroE, who has created a family of 850+ Clicks for most I/O functions you may envision. For each of the Click boards stocked by Parallax, you will find a documented Spin 2 code example on our Propeller GitHub Object Exchange. Connect your Click boards to the Propeller 2 Evaluation Board or P2-EC Edge Breakout Breadboard using the #64008 P2 to MikroBus Click Adapter.
-
Product
LSM6DSL Click
64207
-
Parallax speeds the process of Propeller 2 development through our partnership with MikroE, who has created a family of 850+ Clicks for most I/O functions you may envision. For each of the Click boards stocked by Parallax, you will find a documented Spin 2 code example on our Propeller GitHub Object Exchange. Connect your Click boards to the Propeller 2 Evaluation Board or P2-EC Edge Breakout Breadboard using the #64008 P2 to MikroBus Click Adapter.
-
Product
MicroSemi-SiC-Module / Evaluation Board
EV-MS4135PL1Z-U1 Pre-Release
-
High power evaluation board, up to 1200V & 50A @ 200kHz switching frequency featuring the combo ADI ADuM4135 isolated gate driver + LT3999 isolated power supply controller + Microsemi SiC power module in half bridge configuration.
-
Product
SparkFun FM Tuner Basic Breakout
Si4703
-
This breakout for the Silicon Laboratories Si4703 FM tuner chip is a little more stripped down than our FM Tuner Evaluation Board. If your project already has an amp and just needs a full-featured FM tuner, this is the board for you. Beyond being a simple FM radio, the Si4703 is also capable of detecting and processing both Radio Data Service (RDS) and Radio Broadcast Data Service (RBDS) information. The Si4703 even does a very good job of filtering and carrier detection. It also enables data such as the station ID and song name to be displayed to the user.
-
Product
Carrier Boards
ROM-DB7500
Carrier Board
ROM-DB7500 is an Evaluation Carrier Board designed for Advantech's RISC Qseven module. It is compatible with the ROM-7420 Qseven module and provides a thorough environmentfor RISC module board evaluation. It supports wide range temperatures and 12V power input through AC/DC power adapter.
-
Product
78-Pin D-Type Male Breakout DIN Rail
40-967-078-M
Breakout Board
This termination option is capable of accepting heavy duty connection wires and uses rising clamp screw terminals to minimize the danger of copper strand damage. Users should care take to protect the termination, provide a suitable method of restraining the cables, and ensure appropriate electrical safety precautions are observed.
-
Product
Analog-to-Digital Converter Board
VME-3125A
Converter Board
Isolated Scanning 12-bit 32-Channel Analog-to-Digital Converter Board (6U) with Built-in-Test (BIT)
-
Product
Development Board
SOM-DB5920
Carrier Board
Development Board for COM Express® R3.0 Type 7 Modules. PICMG COM.0 R 3.0 Type 7 Pin out. COM Express ® Basic/Compact module, 10 Gigabit Ethernet support by OCP mezzanine card. Extension: PCIe x16, PCIe x8, 2 PCIe x4.
-
Product
Motion Control Terminal Board For Mitsubishi J2S-A Servo Amplifiers
DIN-812M0
Terminal Board
- On-board connector type: 100-pin SCSI-II female- Suitable for Mitsubishi J2 super servo- Dimensions: 123 mm x 107 mm x 44 mm (WxLxH)- Available for PCI-8132
-
Product
COM Express Type 10 Reference Carrier Board
miniBASE-10R
Carrier Board
The COM Express approach of custom carrier combined with off the shelf system cores is an excellent solution when you need to customize but lack the time or quantity for a complete redesign. It fits most system integration projects with production volumes from 500 to 10,000 pcs per year. The COM Express concept has a great many advantages over full custom designs, it reduces engineering complexity, lowers the threshold for total project quantity and last but not least brings your product to the market in no time. The average time to design a carrier board is less than half the time of a full custom OEM board.
-
Product
6U CompactPCI Dual 64-bit PMC Slots Carrier Board
cPCI-8602
Carrier Board
- Supports two single-size 32,64-bit/33,66 MHz PMC sites in 4HP width- PICMG® 2.0 32,64-bit/33,66 MHz cPCI bus- PICMG® 2.1 Hot Swap Specification Compliant- 3.3V or 5V V(I/O) for cPCI bus and PMC sites- PLX® PCI-to PCI bridge PCI6154 for PCI bus- Power and HotSwap LED incidators on front panel
-
Product
1U Storage Chassis For EATX/ATX Server Board With 8 Hot-Swap Drive Bays For High-Density Storage Servers.
HPC-8108
Server Board
1U rackmount chassis support EATX/ATX motherboard8-bay hot-swappable 2.5" SATA/SAS/SSD drive bays with slim ODDSupport 12Gb/s SASIIIAnti-vibration FAN designSingle front USB2.0 port
-
Product
High-Resolution VMEbus Laser Axis Board
10897D
Laser Board
The 10897D High-resolution VMEbus laser axis board provides excellent resolution of up to 0.3 nm with a high resolution interferometer. The data age uncertainty is dramatically reduced allowing extremely accurate measurement and control of moving systems. The very high data rates accommodate high-bandwidth and high-performance closed-loop applications. Configured with appropriate lasers and optics components, the 10897D supplies unsurpassed positioning accuracy for dynamic measurement.
-
Product
3U CompactPCI Serial MXM GPU Carrier Card
cPCI-A3MXM
Carrier Board
- Follow PICMG® CompactPCI® Serial design guide- CompactPCI® Serial, 3U 4HP/8HP (100mm x 160mm)- Compatible with MXM Type A (82 mm x 70 mm) or Type B (82 mm x 105 mm)- Support NVIDIA A1000 with 2048 CUDA® cores, 16 RT Cores and 64 Tensor Cores or NVIDIA RTX™ A4500 with 5888 CUDA® cores, 46 RT Cores and 184 Tensor Cores- 4x DisplayPort 1.4, support 4K (3840x2160) resolution- Operating temperature: -40°C to +70°C- Designed to meet EN50155 standards
-
Product
FPGA Processing Board
VP880 / VP881
FPGA Board
The VP880 / VP881 is a high-performance FPGA processing board featuring Xilinx® Ultrascale™ and Zynq® Ultrascale+™ technology. It is designed for the most demanding, mission critical military/defense applications such as electronic warfare / DRFM, radar/sonar image processing, satellite communications systems, multichannel digital transmission/reception and advanced digital beamforming.
-
Product
COM-HPC Client Type Reference Carrier Board in ATX Form Factor
COM-HPC Client Base
Carrier Board
The COM-HPC Client Base is an ATX size COM-HPC Client Type reference carrier board based on PICMG COM-HPC Revision 1.0. Together with the COM-HPC Client Type module of your choice and off the shelf add-on cards, you can quickly emulate the functionality of your desired end product for software development and hardware verification.
-
Product
Digital Input Board
VME-1129
Digital Input Board
VME-1129 128-bit high voltage digital input board with Built-in-Test and input filter. This product complies with the VMEbus specification (ANSI/IEEE STD 1014-1987, IEC 821 and 297), with the following mnemonics: A24:A16: D32/D16/D08 (EO): Slave:39/3D: 29/2D Form Factor: 6U
-
Product
Printed Circuit Board
RISER-PPM-1
Printed Circuit Board
WINSYSTEMS’ RISER-PPM-1 boards are designed to provide extra space in a PC/104-Plusstack. They are printed circuit boards (PCBs) with PCI-104 mounting holes and bus connectors. They allow a board with either tall components or heat sinks to be placed in a stack of boards in a location other than only at the top. The additional separation is 0.60 inches using standard PC/104-type spacers.
-
Product
3U CompactPCI Serial M.2/U.2/SATA Storage Carrier
cPCI-A3H20
Carrier Board
- 1x NVMe M.2 and 1x NVMe U.2 drive slot- 1x optional SATA 6Gb/s M.2 drive slot shared space with NVMe U.2- Status LEDs on faceplate: drive activity, hot-swap status, user-configurable- Operating temperature: -40°C to +85°C with qualified modules- EN50155 compliant
