RF Sources
Produce Radio Frequency (RF) signal.
-
Product
RF Shielded Test Enclosure
JRE 0709-P
-
Containing all the capability of the larger JRE enclosures, the compact JRE 0709-P is ideal for small wireless devices such as; cell phones, pagers, WiFi dongles and other small RF devices. Featuring rugged welded aluminum construction, you can be assured of its tight RF shielding effectiveness. Long life door gasket material along with double edge engagement not only provides solid RF shielding, but smooth troublefree operation over its lifespan.
-
Product
PXI Triple SPDT RF Switch 3GHz 50 SMB
40-870-003
Switch Module
The 40-870 is a 50 RF Switch available with 3 or 6 separate SPDT relays in a single PXI slot. Both versions exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz. The injection of noise and unwanted signals into the signal paths of the 40-870 has been minimized by careful attention to the mechanical and electrical design.
-
Product
RF Filters - Notch
-
A specialized band-reject filter that blocks or significantly weakens a very narrow range of unwanted frequencies (the "notch") while letting all other desired frequencies pass through relatively unchanged.
-
Product
Single 16 to 1 50 600MHz PXI RF Multiplexer
40-764-001
Multiplexer Module
This 4 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
Product
Single 16 to 1 Terminated 50 600MHz PXI RF Multiplexer
40-765-001
Multiplexer Module
This 4 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
Product
RF Connectors
SMP Connectors
-
The SMP interface is a subminiature interface in the same scale as MMCX connectors but offers a frequency range of DC to 40 GHz. It is commonly used in miniaturized high frequency coaxial modules and is offered in both push-on and snap-on mating styles.
-
Product
Source Measure Unit (SMU)
-
Source and Measurement Units (SMUs) are devices that generate voltages or currents and can measure them simultaneously using the integrated measurement units (VMU, CMU).
-
Product
SP16T RF Pin Diode Switches To 10 GHz
-
Pulsar Microwave's 16-way switches cover 500 MHz to 10 GHz in single pole, 16-throw configuration. Maximum input power is 200 mW and switching time is 100 ns. SMA female connectors are standard. A 15-pin D-SUB male connector makes the internal connections to the power, ground and logic circuitry. Switching control is TTL with the option of line drivers and decoders.
-
Product
MXG X-Series RF Vector Signal Generator, 9 kHz to 6 GHz
N5182B
Vector Signal Generator
Take your designs to their limit with outstanding hardware performance, including unmatched phase noise & spurious characteristicsDrive power amplifiers & characterize nonlinear behavior with industry-leading ACPR & output powerTest wideband devices with factory-equalized 160 MHz RF bandwidthReduce the time spent on signal creation with Signal Studio software, including LTE, WLAN & GNSSLower your cost of ownership with 3-year cal cycles & comprehensive solutions for self-maintenance
-
-
Product
PoE Power Sourcing Equipment For TBOX300/tBOX400/tBOX500 Series
PSU120-259
-
*M12 5P DC input*Terminal block PoE power output, maximum 120W*Designed for tBOX300/tBOX400/tBOX500 series*CE, FCC, EN 50155 and IEC 60945 compliant
-
Product
SNS Series Noise Source 10 MHz to 26.5 GHz (ENR 15 dB)
N4002A
-
The SNS series N4002A noise source was designed to measure DUT noise figures reliably and accurately up to 30 dB from 10 MHz to 26.5 GHz.
-
Product
MP field sources calibration set
-
The MP field source calibration set is used to measure electric or magnetic fields in a frequency range up to 3 GHz. RF fields or transient fields can be measured. The MP field source calibration set is used to check fields of the Langer EMV-Technik GmbH field sources, fields of TEM cells and IC striplines.
-
Product
Light Source
LS-HA
-
provides the stable and smooth wide-band spectral output. It’s proper for most visible to near infrared range measurement. This light source is also designed to be used in the standard measurement package. It ‘s a simple and quick measurement platform.
-
Product
RF Shielded Test Enclosure, Low Profile
JRE 2214
-
Like its other brothers in the JRE test line, it features rugged welded aluminum construction with superb RF shielding effectiveness. Long life door gasket material along with double edge engagement not only provides solid RF shielding, but smooth trouble-free operation over its lifespan. Tough 'honeycomb' vent maintains shielding effectiveness throughout the full frequency range. Optional fan is available for additional airflow.
-
Product
Portable Cable/Digital TV RF Analyzer
SLM 1479
-
7” full-color, high-resolution touch screen user interface simplifies complex measurement tasksFull motion video and audio decoding of received channelsDigital RF measurements including average power/level, pre/post BER, MER, noise margin, spectral analysis and constellation
-
Product
SP2T RF Pin Diode Switches To 18 GHz
-
Pulsar Microwave's 2-way switches are available in absorptive and reflective designs from 20 MHz to 18 GHz. They are also referred to as single pole, double throw and abbreviated SPDT or SP2T. These switches have a typical VSWR performance of 1.6:1 or better and input power handling of 200 milliwatts maximum. Switching time is 100 nanoseconds, and isolation of 60 dB or greater for most models. Supply voltages are +5V and -5V, with TTL logic control voltage of 0 to 5 volts.Both absorptive and reflective SPDT switches are packaged into Pulsar Microwave's SW2 outline. Configuration is standard with SMA female connectors. Voltage is applied with wire wrap feed thru terminals. The housing serves as electrical ground, and two turret terminals are installed for wiring.
-
Product
RF Connectors
BNC Connectors
-
BNC connector types feature a bayonet style coupling mechanism that allows for quick connect and disconnect with positive locking. Mating is achieved with just a quarter-turn of the coupling nut. With a classic, dependable design, BNC RF connectors are suited to accommodate a large variety of RG and industry-standard coaxial cables, in a variety of termination styles.
-
Product
Advanced Reconfigurable Modular OTA RF Test Enclosures, ≥100 DB Isolation, 300 MHz - 90 GHz
dbSAFE ARMOR
-
The dbSAFE ARMOR series of shielded boxes are cost-effective solutions for OTA testing in the mmWave spectrum. Providing a shielded, fully anechoic test environment, these RF test enclosures ensure stable and repeatable measurements over a wide frequency range (from 300 MHz to 90 GHz).
-
Product
PXI Hex SPDT RF Switch 6GHz 50 SMA Terminated
40-880-003
Switch Module
A range of 50Ω SPDT RF switching with automatic termination of unused signals. Available as a dual switch in a 1 slot PXI module, a quad switch in a two slot PXI module or hex and octal switches in three slot PXI modules.
-
Product
Module Type ASE Light Source
-
Module type ASE light sources are small in size and easy to integrate into equipments. The dimensions are different between models, and five sizes are available from the smallest MSA to S, M, M2 and L. All of them are operated on 5 VDC and the optical properties are the same as the corresponding bench-top models.
-
Product
3D RF Noise Measurment System
EMI-360
-
3D RF Noise Measurement System EMI-360 to realize the new EMC measurement.EMC measurement is possible to realize a low-cost and time reduction.
-
Product
RF Multi-Coupler
MC108-2
-
Systems Engineering & Management Company
The MC100 Series Multi-Coupler is a 1U Rack-Mount device that provides RF distribution form 200 MHz to 5250 MHz. Both single and dual output configurations are available, as well as up to 8 output channels. Each output is an independent channel with +/- 5 dB gain controls, providing the ability to balance all outputs within +/- 1 dBm. Frequency Channel selection is from both front panel controls as well as remote control via Ethernet and SEMCO's MCCS Network software program.
-
Product
Noise Bridge, RF 1 MHz to 100 MHz
MFJ-202B
-
Quickly adjust almost any antenna for maximum performance, 1 to 100 MHz. Lengthen or shorten your antenna for minimum SWR. Measure resonant frequency, feedpoint resistance and reactance. Works with any receiver or transceiver. Hand-calibrated resistance scale, expanded capacitance range and exclusive built-in range extender.
-
Product
Broadband Coaxial Noise Sources
-
Our integrated noise modules contain all the required biasing circuitry and only need a positive voltage to activate for an easy installation. Since they typically do not contain amplification, the raw noise output from the diode is seen at the output of the module resulting in a maximum ENR of approximately 35dB. Primary applications include system built-in test and laboratory use.
-
Product
Uniform Light Sources With Continuous Emission Spectrum
-
Tungsten halogen lamp based uniform light sources with options like manual or remote control variable intensity or monitor detectors.
-
Product
Calibration Light Source
CAL1
-
Image Engineering GmbH & Co. KG
The one light source solution in the field of camera characterization and calibration. CAL1The CAL1 calibration light source is designed to characterize and calibrate cameras in the lab or on the production line. Its compact design consists of one iQ-LED element in a 0.3 m integrating sphere that illuminates a 70 mm opening. Because of the non-reflective special diffusor filter on the sphere opening, a uniformity of more than 98% could be reached
-
-
Product
Process RF Sensors
-
Process RF (radio frequency) analyzers using penetrating radio waves to determine the moisture content across a full sample thickness. Single point, array and hand-held analyzers provide a variety of sampling options from fully integrated in-process moisture profiling to at-line quality control. RF analyzers are widely used in gypsum, panel board, and other industrial processes.
-
Product
Fixed Aperture RF Current Monitoring Probe
TBCP1-200
-
The TBCP1-200 is a fixed aperture RF current monitoring probe.The probe has a 3dB bandwidth of approximately 200 MHz. The aperture of the RF current monitoring probe is 25 mm. Its transfer impedance is > 14 dB Ohm in the range from 40 kHz to 200 MHz.
