Subsea
See Also: Water, Water Quality, Water Meters, H2O, Wastewater, Underwater, Water Spray, Water Leak, Water Flow, Sea
-
Product
Subsea Shackle Load Cell
SUBS-3.0
-
The Subsea Shackle Load Cell has been designed to measure loads in a subsea environment. DLM’s subsea shackles are suited to fit leading industry Crosby and GN shackles.
-
Product
10 kV Subsea Power System
-
The Teledyne Oil and Gas 10 kV subsea power electrical connection system is a three-phase system rated to 250 A and 6/10 (12) kV. The electrical connection system is designed to provide power to motors used for subsea pumping systems.
-
Product
Next Generation Subsea Attitude and Heading Reference Systems
TOGS
-
The new TOGS subsea navigation system is built on core TSS fibre optic gyro (FOG) navigation technology with significant improvements in efficiency and functionality. It is available in three standard heading accuracy variants: 0.1° (TOGS1), 0.3° (TOGS3) and 0.5° (TOGS5), all rated for operational depths to 4,000m or 6,000m. Attitude data is delivered via accurate roll/pitch measurement capabilities of 0.01° (TOGS1) and 0.05° (TOGS3 and TOGS5), and a heave performance of 5cm or 5%.
-
Product
Subsea Pipe and Cable Detection & Tracking System
HydroPACT Dualtrack
-
Dualtrack is the combination of the 440 and the 350 systems to provide the ultimate subsea detection system, capable of tracking and surveying pipes and cables via ROV deployment.It utilizes the same industry standard pulse induction technology as the 440 system to survey accurately regardless of vehicle heading. The accompanying display and control software is Windowsâ„¢ based providing a familiarity factor that a specifically built interface would not.
-
Product
Subsea Pipe Detection & Tracking System
HydroPACT 440
-
The HydroPACT 440 pipe detection system has been established for a number of years as the industry standard, providing accurate and reliable survey data, which provides the position of conductive assets on or beneath the seabed. The system is flexible in its range of uses and can be installed on a variety of vehicles for undertaking survey work.It provides a reliable and simple method for performing accurate submarine surveys on a conductive target such as a cable or pipe.
-
Product
Subsea Multiphase Sampler
-
The Mirmorax Subsea Multiphase Sampling System provides the operator with a sample that, independent of flow regime and compositional mix, is a true volumetric representation of the flow.
-
Product
Subsea Cable Detection & Tracking System
HydroPACT 350
-
The HydroPACT 350 provides a reliable and simple method for performing accurate submarine surveys on a tone-carrying cable. It is available as a 110V system or a 240V system, both depth rated to 3,000m with a 6,000m option.The 350 system operates in real-time and provides accurate measurements at a rate that allows integration on faster ROVs. The measurement technology used by the system also allows it to operate out of water with no degradation in performance, range or accuracy.
-
Product
Bulkhead Penetrator for Subsea Applications with 4, 7, or 12 Circuits, 30 A
P1.7-30 Electrical Penetrator
-
ODI's P1.7-30 penetrators meet the same electrical performance characteristics as Nautilus connectors and are used where the need to mate and demate is not necessary, generally at the second end of a pressure-balanced oil-filled (PBOF) assembly with a Nautilus connector at the opposite end. The Penetrator is typically attached directly to a vessel, which can be either pressure balanced or at 1 ATM.
-
Product
Subsea Imagery
-
With only 24% of the ocean floor being mapped with a submetric resolution, the ocean’s seabed is Earth’s last frontier. Mapping the seafloor, protecting marine habitats, hunting for wrecks, studying underwater geo-hazards…Those are challenges for the years to come.It is to help in that field, that Exail has developed a large range of sensors designed to address the full spectrum of subsea imagery applications, from sub-bottom profiling and seabed mapping to water column monitoring.
-
Product
Subsea Data Logger
DL-3.0
-
The Subsea Data logger is proprietary data logger design by DLM for use in the offshore industry. Comprising of multiple on-board sensors and with extra capacity for external mV or mA inputs, the DL-3.0 can sample on-board and external sensors at customisablesample rates of up to 800Hz.
-
Product
O-Band Interleaver For 5G-PON Mux/DeMux
-
Optoplex has been the leading technology innovator and marker leader of optical interleavers for optical communications. • Technology and market leader of interleaver for optical communications• Dominant supplier of optical interleaver for global subsea network applications• 1st company of 25GHz interleaver • Proprietary Co-Packaged interleaver (Mux/DeMux)• Proprietary “Super” wide passband interleaver• A leading company of O- and E-band optical interleavers for 5G Mux/DeMux applications
-
Product
Load Pin Products
-
DLM are world renowned for the design and manufacture of custom design load pins for a host of industries, including offshore moorings, renewable energy and marine & subsea applications.
-
Product
Ruggedized Ethernet Cables
-
Teledyne Marine Cable Solutions
Ruggedized Ethernet cables from Teledyne Storm Cable are used in a variety of applications, from the land based Oil & Gas industry to deep water subsea applications. The cables are designed to maintain the integrity of high speed Ethernet data transmission while surviving in harsh environments.
-
Product
Underwater Thickness Gauges
-
Cygnus have created a range of versatile underwater and subsea thickness gauges for use by divers and engineers. These measuring devices provide a simple and time-saving method of obtaining ultrasonic thickness measurements in underwater conditions.
-
Product
Subsea Data Logging Tensile Link
SUBD-3.0
-
The Subsea Data logging Tensile Link is a robust Tensile Link used for measuring loads on subsea mooring lines, underwater deployments and other similar applications. The instrument measures and records the applied load using an internal data logger which was developed by DLM Design Engineers.
-
Product
Subsea Tensile Link
SUBT-3.0
-
The Subsea Tensile Link is specially designed for working in subsea conditions and is used for measuring tensile loads. With an optional integral 4-20mA amplifier the load cell is packaged in a wooden case with a subsea rated signal cable to customer specific lengths or alternatively can be supplied with a TW-3.0-S display. Fully sealed with a subsea connector and pressure tested to over 250Bar the load cell is the ideal instrument for easily and accurately measuring subsea loads.
-
Product
Encapsulation and Molding
-
The underlying science of adhesion and immersion has been extensively studied, simulated, and tested at Teledyne Impulse-PDM's laboratory in Alton, UK. With more than 25 years' experience in subsea engineering, Impulse-PDM offers high quality design and development services for all connectivity requirements.
-
Product
SEA CLIP™ Sensor & Aqua MER™ Meter
-
The SEA CLIP™ by Swain Meter is a high-quality, hydraulically actuated clamp-on DC ammeter for ROV. It is useful for measuring DC currents in subsea cables, cathodic protection systems, and subsea pipes up to 4” in diameter. The SEA CLIP™ can be used with an optional 200-foot cable to a topside meter, or in concert with the Aqua MER™ subsea meter at depths up to 6900 feet of seawater.The Aqua MER™ ROV meter is based on Swain’s proven MER2™ technology, specially adapted to the demanding requirements of the subsea environment and updated to provide RS-485 communication over twisted pair, or fiber optic data transmission protocols.
-
Product
Omnisens Securing Power Cable Integrity
https://www.omnisens.com/uploads/1/2/0/5/120592129/published/omnisens-cobra-logo-white-2014-06-10.png?1546958203
-
In both underground and subsea cables incipient faults often result in temperature events. Using optical fibers integrated into the power cable or laid close by, Distributed Temperature Sensing (DTS) helps detect changes and faults allowing the operator to intervene before the cable fails. It is suitable for deployment in any cable where an optical fiber is present, including HVDC, HVAC, export, inter-array, transmission and distribution.
-
Product
Rolling Seal 8 Optical Connector - APC (RS8 APC)
-
The Angled Physical Contact Rolling Seal 8 Connector (RS8 APC) from Teledyne ODI is a wet-mateable optical connector with angled endfaces. The design reduces signal interference due to reflections at the connector face, supporting the next generation of subsea optical communication equipment. The Rolling Seal design provides isolation from seawater and silt when the connectors are unmated. As the seals rotate, the fibers join inside a clean, oil-filled conduit, resulting in a reliable optical throughput. The RS8 APC incorporates RS8 Mark III design features to enhance operational efficiency and reduce risks during ROV intervention.
-
Product
Wet-Mateable Connector, 10k V, 250 A
Nautilus WM10-250
-
Trends in subsea oil & gas production are moving towards deeper water and longer step out distances. These trends drive demand for higher power equipment and higher power delivery and distribution capabilities subsea with high pressures and temperatures. Teledyne ODI'™s Nautilus WM10-250 is designed with the benefit of advanced material science testing and certification, and with insulation and redundant sealing systems for reliable performance in long-term harsh environments.
-
Product
Subsea Navigation
-
Explore our comprehensive range of navigation products and stay updated on our latest innovations in navigation technology. Whether you are operating shallow-water AUVs or piloting ROVs at depth, our Doppler Velocity Logs (DVLs) are essential to subsea vehicle navigation systems. Often paired with inertial sensors like AHRS or INS, our DVLs ensure precise and reliable navigation tailored to your needs.
-
Product
Trackit USBL System
-
The first in a series of Teledyne Benthos USBL deliverables, the "Short Range USBL" is geared toward the tracking and positioning of shallow water autonomous or remotely operated vehicles. Leveraging Teledyne Benthos extensive technical expertise and field experience in acoustic positioning and communications, this new system brings it all together with a powerful topside processing package, intuitive user interface, communications, and highly accurate, field proven subsea electronics.
-
Product
Tasman DVL
-
Teledyne Marine RD Instruments
Teledyne RDI’s new Tasman DVL represents the next generation of DVL technology, taking your navigation to the next level. Teledyne RDI’s long-standing Workhorse Navigator was the first DVL to enter the market, and remains the gold-standard for precision subsea navigation around the globe. However, the new Tasman DVL, with its wide array of advanced features, reduced size, and increased range, is ready to replace this industry icon. Other new features include enhanced broadband signal processing and an innovative, cost-effective field-replaceable phased array transducer design.
-
Product
Ethernet Flying Lead
-
Qualified 100m Subsea Ethernet jumpers designed for data transmission and real-time situational awareness and monitoring. The typical Ethernet harness system consists of wet-mateable, Nautilus connectors, Nautilus penetrators, and pressure balanced, oil-filled (PBOF) hose conduits. Internally, the Ethernet signals are transmitted over custom Ethernet cabling sealed to seawater ingress by two independent barriers. Seven and 12-way configurations are available. Subsea connection of the harnesses may be accomplished by ROV, Diver-Mate or Stab-Plate applications. For Ethernet needs above 100 meters, see Extended Ethernet Flying Leads.
-
Product
Cormon Integrated Monitoring Software
CIMS
-
Cormon Integrated Monitoring Software (CIMS) processes real-time corrosion, erosion, pressure, or temperature data from up to 50 monitoring sensors to provide a complete picture of pipeline and device health. Alarm functions can be configured to ensure that potential issues are identified with ample time for correction, reducing operational risk and unplanned downtime. CIMS is the only industry software that can bring together data from both topside and subsea sensors, giving operators a comprehensive view into the entire asset integrity program.
-
Product
Electrical Penetrator with High Pressure Barrier, Rated at 10 kV and 250 A
P10-250 Electrical Penetrator
-
For higher subsea power requirements, the P10-250 from Teledyne ODI is designed to provide reliable barrier protection at extreme pressures and temperatures. The penetrator extends through a wall or bulkhead and connects to medium voltage cables to supply an external power source. In electric submersible pumping (ESP) applications, the penetrator transfers power to the motor while maintaining a pressure barrier between the motor and the seawater.
-
Product
Extended Ethernet Flying Lead (E²FL)
-
Due to vast geographies and complex field layout configurations, Subsea Ethernet transmission requirements may reach beyond the 100 meter maximum. Extended Ethernet Flying Leads (E²FL) enables Ethernet transmission beyond the limits of the previous 100 meter Ethernet assemblies.
-
Product
Single Pin Horizontal EFS
-
Teledyne DGO offers an advanced, high-reliability subsea wellhead single channel electrical feedthrough system for use in intelligent completions with permanent downhole instrumentation. The connection system is designed for long-term reliability in the demanding subsea and downhole environments with sour well (H2S) conditions, as well as aggressive production and packer fluids.
-
Product
Acoustic Load Shackle
ALS-2.0
-
The Acoustic Load Shackle is designed for subsea operations where load monitoring is required, either for short term operations lowering an item to the seabed or for longer periods monitoring dynamic loads.
