ECU Simulation
a virtual Electronic Control Unit (Engine Control Unit) used to validate related dynamic systems.
See Also: ECU, ECU Testing
-
Product
Radio Link Simulator
RLS-2100
-
Square Peg Communications Inc.
It is the most comprehensive, with unparalleled impairment simulation, real-time multi-satellite orbit calculation, full motion support and integrated GPS simulators. It is the most flexible, providing end-to-end or single link simulation of wideband terrestrial and satellite networks, satellite selection via open standard interfaces, and facilities to enable seamless integration into more complex test beds if required. It supports the highest bandwidth and has an intuitive, user-friendly interface. And it does it all in one box.
-
Product
PXI 16 Channel Switch Simulation Module
40-480-121
Switch Simulation Module
The 40-480 is designed to simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. It allows automotive I/O devices to be tested for correct operation under adverse conditions. The design includes protection circuits that ensure module damage cannot be caused by wiring faults or UUT failures. Each module can support up to 32 channels and is suitable for both 12V and 24V automotive applications.
-
Product
Custom Solar Simulation
-
Atlas Material Testing Solutions
Solar heat load effects are critical with respect to product functionality, operational performance, thermal management, noise and dimensional stability. Therefore, any new product made from different materials and components should be tested under solar environmental conditions representative of those locations in which it will exist - anywhere ranging from the heat of the Australian Outback to the frigid climate of arctic regions.
-
Product
ARINC 429 USB & LAN Test & Simulation Module
UXI-429
-
Avionics Interface Technologies
8 Channel (4Tx/4Rx) & 16 Channel (8 Tx/8 Rx) models available - Programmable Tx channel output amplitude - Programmable high/low speed operation - Concurrent operation of all Tx/Rx channels at high speed rates - Full error injection & detection - Rate-oriented label transmission - Label selective trigger for capture/filtering - Real-time recording & post analysis of multiple channels - Physical Bus Replay - Onboard IRIG-B time code encoder/decoder for Synchronization - Time Synchronization to IEEE 1588 via Ethernet LAN port - 10 Discrete I/O Interfaces (5 Outputs / 5 Inputs)
-
Product
3U VPX RL Thermal Load Simulation Module
-
The 3U power test module is an ideal solution for evaluating heat dissipation in a rugged conduction cooled VPX cage or chassis. This card is a thermal load in the chassis to evaluate the heat dissipation. The chassis can be monitored with temp sensing probes and or FLIR imaging. Different wattages are selected by setting dip switches. The +5 and 3.3V loads are on the top of the module. The +12V and -12V loads are on the bottom side of the module.
-
Product
Circuit Breaker Simulation Device
PSS01
-
PSS01 is the circuit breaker simulator，which can conduct circuit breaker simulation to test the whole secondary relay scheme together with relay test set. It is very good accessory for protection relay test kit to avoid complicated software programming to finalize the same test.
-
Product
PXI Strain Gauge Simulator Module 4-Channel, 3k
40-265-104
Strain Gauge Simulator
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 4-channel, 3kΩ) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
Product
Highly Collimated Solar Simulators
-
This solar simulator is based on a Fresnel lens to collimate the light beam from the arc lamp source to infinity, which results in highly collimated illumination of the target spot. A 2.5kW xenon ozone free lamp is used as the light source. The spectral distribution of the xenon light source, along with the use of specially calibrated AirMass filters, closely simulates the sun’s true spectral distribution in various conditions on Earth.
-
Product
NIBP Simulator for Testing Patient Monitors
SECULIFE BP PRO
-
The SECULIFE | BPPRO is the high-end product from the new range of NIBP simulators and is distinguished by a great variety of functions. It includes functions such as NIBP, IBP, ECG, temperature, arrhythmia, respiration, leak detection and much more. Specially developed to cover a great diversity of functions and nevertheless to ensure a compact design, the SECULIFE | BPPRO fulfills the requirements of modern medical technology. It makes no compromises with regard to functionality and input diversity. There's hardly another product with a similarly large range of features.
-
Product
AC Load Simulating Inductors
-
Osborne designs our AC Inductors to provide the desired inductance and to perform effectively with the dissipation characteristics presented to the circuit. Dissipation characteristics depend on circuit current and operating frequency. The Osborne design approach is unique to the extent that we design for frequency effects. The resulting inductors deliver superior performance.
-
Product
Accelerometer Simulator
MTN/8302
-
The MTN/8302 is a battery-powered unit designed to simulate a constant current type accelerometer. It enables test and calibration of vibration monitoring equipment such as the Monitran MTN/6000 series.
-
Product
Cost-Effective Network Simulator
Emutel Maestro
-
Emutel Maestro brings you the perfect solution for testing your DSL equipment. Connect to your product while still in your own testing lab and perform those final tests in a real environment, enabling you to identify and solve any problems before they occur on site.
-
Product
Battery Simulator
G5.BAS
-
The G5.BAS series is bidirectional regenerative. It was developed specifically for the simulation of energy storage devices and batteries and is suitable for use in laboratories and on test benches. The modular and finely graded G5.BAS series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3.
-
Product
PXI Analog Output/Current Loop Simulator Module - 8 Channel
41-765-003
Analog Output Module
The 41/43-765-003 is an 8-channel Analog Output Module designed to meet the requirements of industrial control applications utilizing current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signaling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
Product
ARINC 429 Test And Simulation PMC Module
PMC-429
PMC Module
*4, 8, 16 or 32 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*PXI interrupts, star trigger, and PXI clock*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*Sorting according to SDI field*VXI Plug & Play driver including soft front panel*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
Product
2 PRI + 16 BRI-S/T ISDN Simulator
CH-16BRI-ST-MOD-2PRI
-
This unit has two PRI ports and 16 BRI ports allowing ISDN equipment to be connected together just as if they were connected through the ISDN network
-
Product
Mobility Simulator Creates V2X Environments For Testing
MxDrive™
-
MxDrive is a multi-vehicle and infrastructure mobility simulator that provides an environment to generate and run real-world conditions to test connected vehicle applications. Testing V2X applications on actual roads has limitations. Only a limited number of test conditions can be achieved, while safety and damage risks further limit test coverage. MxDrive combined with the MxSuite ecosystem significantly simplifies the testing of Advanced Driver Assistance Systems (ADAS), Sensor Fusion, Radar, and V2X. MxSuite is ISO 26262 qualified to test safety applications for OEMs and suppliers.
-
Product
Monitoring & Simulation
-
ETAP Power System Monitoring & Simulation (PSMS) is at the heart of the ETAP Real-Time power management system. Power System Monitoring & Simulation is the smart choice for both small and large electrical utility systems, generation plants, industrial sites, manufacturing facilities, and off-shore oil platforms.
-
Product
PXI Thermocouple Simulators
-
Our PXI Millivolt Thermocouple Simulator modules provide 32, 24, 16 or 8 channels of accurate low sources. They are ideal for the simulation of thermocouples and can be used for sensor emulation in ECU testing. The channels can be operated with one of three voltage ranges covering most thermocouple types. We can also supply connection solutions allowing the easy integration of the Thermocouple Simulator into your test system.
-
Product
Voltage Dip & Swell Simulators
VDS Series
-
A simulator to reproduce voltage variation phenomena in commercial power supplies (AC100V/200V).This type of immunity test against voltage variation phenomena is defined in IEC 61000-4-11 and is widely used in many industries.
-
Product
Single Or Dual Stream MIL-STD-1553A/BTest And Simulation Module For Standard Ethernet
ANET1553-x
-
The ANET1553-x is a member of AIM’s new line of Ethernet based modules for analysing, simulating, monitoring and testing MIL-STD-1553A/B databuses. For wireless applications, an ANET compatible USB Wifi dongle is optionally available. The capability to execute Python scripts in the ANET is a standard feature. For applications with multiple ANET devices AIM offers the ADock ANET Docking Station to host up to 4 ANET modules.
-
Product
Integrated AI-ADAS ECU And Cameras For Large Commercial Vehicle
ADM-TJ30
Electronic Control Unit
The integrated AI-ADAS ECU is connected to 8 cameras and powered by the vision-AI algorithm. It can detect and classify different kinds of vehicles/ pedestrians/ two-wheeler riders/ lane marking and other objects to perform multiple ADAS functions.
-
Product
Single, Dual Or Quad Stream MIL-STD-1553A/BTest And Simulation Modules For PMC
AMCX1553
-
MIL-STD-1553 Test and Simulation modules for PMC with 1, 2 or 4 dual redundant channels plus 8 Discrete I/O’s (on Rear-I/O).
-
Product
PXI RTD Simulator Module, 8 Channel, PT100
40-263-401
Simulator
The 40-263-401 is an 8-channel PT100 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
Solar Simulators
TriSOL CPV
-
Concentrating Photovoltaics (CPV) has the promise of producing solar cells with high cell efficiencies, which result in a reduction in the cost of operating a PV module. However, a CPV system requires the integration of CPV solar cells, modules and CPV optics into one efficient system. OAI’s focus is CPV cell testing methodology. The CPV cells can now be tested using OAI’s advanced standalone CPV Simulators for low dose and high dose configurations. The low dose CPV Solar Simulator provides exposure up to 50 Suns, whereas, the high dose CPV Solar Simulator provides exposure up to 1500 Suns. The low and high dose simulators provide exposure in varying Sun concentrations in various beam sizes from 1.5cm x 1.5cm to 7.5cm x 7.5cm, and may be configured with OAI’s I-V Test Systems.
-
Product
Walk in Chamber for Altitude Simulated Test
-
Guangdong Bell Experiment Equipment Co.,Ltd
Walk in Chamber for Altitude Simulated Test Relative Standard test requirementsTest Object: battery pack and systemTest Conditions: Altitude 4000m or the equate air pressure condition, atroom temperature.The test objects stay in the test condition as Item 2 for 5 hours.Subject the test object to 1C(no more than 400A) constant current discharge until reaching the cutoff condition.After testing, observe for 2h under the room temperature.
-
Product
MIL-STD-1553 A / B Test And Simulation VME Module
VME-1553
-
*Dual redundant*1, 2, 4 or 8 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*VISA based VXI Plug & Play driver*Optional twinax front end
-
Product
LED solar simulators
-
We offer innovative A + A + A + LED solar simulators for the integration of the production process and for the stand-alone operation in the laboratory or goods receipt. Our LED solar simulators are characterized by maximum repeatability, a long pulse duration and very low maintenance.
-
Product
Computer simulators
-
There are three computer simulators offered by INFRAMET:*SIMTERM - computer simulator of thermal imagers,*VIRTEST - computer simulator of test proces thermal imagers ( MRTD measurement)*NIGHTMET - computer simulator of image intensifier tubes
-
Product
Signal Integrity Studio, Analysis & Simulation SW for WAVEPULSER High-Speed Interconnect Analyzer
WavePulser-Signal Integrity (SI) Studio
Analyzer
WavePulser Signal Integrity (SI) Studio is included as a single license in the WavePulser 40iX-BUNDLE or can be purchased as an additional license for offline access to additional users. WavePulser Signal Integrity (SI) Studio combines S-parameter, Impedance profiling and de-embedding measurements, channel and equalizer modeling, eye diagrams and jitter analysis in a single affordable software package for emulating the complete serial data channel.
