Carbon Dioxide
An acidic oxide chemical compound.
-
Product
Determines Presence of Carbonation on Concrete Samples
Carbo Detect System™
-
Carbo Detect is a simple colored dye field test for detecting carbonation. The single reagent is sprayed on the surface to be checked. The reagent will change to pink in uncarbonated concrete and remain colorless when sprayed on carbonated concrete.
-
Product
500 AMP Carbon Pile Load Tester
710
-
The #710 will perform variable load testing on 12 volt batteries rated as high as 1000 Cold Cranking Amps. Use this battery tester to simulate actual cranking loads. Also tests alternator charging voltage and relative starter current draw. The #710 features large dual meters to display the battery voltage and load current simultaneously, during the test.
-
Product
Carbon / Sulfur Analyzer
EMIA-Pro
-
The EMIA-Pro, Carbon/Sulfur Analyzer is based on HORIBA''s vast knowledge of Non-Dispersive Infrared (NDIR) technology and our wealth of experience acquired from our EMIA series. EMIA-Pro offers improved the cleaning efficiency, enhanced user-friendly software, durability, operability and maintenance to ensure efficient measurements and its shortened measurement cycle time accelerates repetitive measurements up to 200 times, thus improving development and manufacturing speed.
-
Product
Flat Carbon Sensor Conductivity meter
HE-960LF / FS-09F-1/2
-
It is effective to keep the dilution of Slurry constant. Maintaining an appropriate conductivity value contributes to process stability in the wafer polishing process. Even highly viscous sample liquids such as CMP Slurry can be measured without problems because they use a sensor structure that reduces the risk of the sample liquid sticking to the electrodes. In addition, the sensor is made of a wetted material with excellent chemical resistance, which meets the cleanliness requirements of semiconductor processes. In addition to the above, it can also be used for introduction at the semiconductor process development stage and conductivity control of special chemicals.
-
Product
500 AMP Carbon Pile Load Tester
CP710
-
Tests batteries rated as high as 1000 CCA or 160 amp hour. Also tests alternators, regulators, and starters
-
-
Product
Total Organic Carbon Analyzer
TOC-L Series
-
The TOC-L series of TOC analyzers adopts the 680°C combustion catalytic oxidation method, which was developed by Shimadzu and is now used worldwide. While providing an ultra wide range of 4 μg/L to 30,000 mg/L, these analyzers boast a detection limit of 4 μg/L through coordination with NDIR. This is the highest level of detection sensitivity available with the combustion catalytic oxidation method. In addition, the combustion catalytic oxidation method makes it possible to efficiently oxidize not only easily-decomposed, low-molecular-weight organic compounds, but also hard-to-decompose insoluble and macromolecular organic compounds.
-
Product
High Performance Carbon Isotope Analysis of LC Separated Compounds
LiquiFace
-
Elementar Analysensysteme GmbH
Compound specific isotope analysis of aqueous samples by LC is highly advantageous for those compound classes which are thermolabile or require derivitisation prior to GC analysis. Samples such as carbohydrates, amino acids, alcohols, organic acids and peptides make ideal candidates for LC-IRMS and the technique has been employed to great success in food and biogeochemistry applications. The LiquiFace works as an interface for the LC system to provide quantitative on-line conversion of organic carbon to CO2 prior to analysis by the IRMS system. Isotopic precision, accuracy and linearity is exceptional due to the highly efficient quantitative conversion of the organic carbon to CO2. This level of performance means that the LiquiFace is able to cover a range of sample types with a complete independence upon sample concentration, making the analysts life even simpler.
-
Product
Sulfur Dioxide Test Machine
SQ-010
-
This instrument is designed according to GB/T2423.19-1981, GB/T2423.33-2005, ISO6988 (replaced DIN50018: 1988-06), DIN50900, DIN53210 and EC, MIL, ASTM etc to do sulfur dioxide gas corrosion test.
-
Product
Carbon Monoxide Detectors for Aviation
AV8 Inspector Collection
-
The Sensorcon AV8 Inspector is a portable, professional-grade Carbon Monoxide monitor designed for aviation enthusiasts and professionals including pilots, ground crew, technicians and inspectors.
-
Product
Mini Carbon Monoxide Gas Detector
Model - KM CO-910
-
Kusam Electrical Industries Limited
KM-CO-910 Carbon Monoxide meter detects the presence of Carbon Monoxide (CO) & measures concentrations between 1-1000 parts per million(PPM). The meter indicates the presence of CO by a reading on the LCD & a beeper tone. The beeper function much like clicking of a geiger counter: above 200PPM, the beeper sounds continuously with the concentration of CO; from 35PPM to 200PPM, the beeper sounds discontinuously with the concentration of CO.
-
Product
Carbon / Sulfur Elemental Analyzer
EMIA-Expert
-
The EMIA-Expert Carbon/Sulfur Analyzer is based on HORIBA''s widely respected expertise in Non-Dispersive Infrared (NDIR) technology. It offers improved the cleaning efficiency, enhanced user-friendly software, durability, operability and maintenance to ensure efficient measurements and its shortened cycle time accelerates your development and manufacturing speed.
-
Product
Carbon Monoxide Detector, CO
ENVIROMUX-CMD
-
Continuous air monitoring. Pre-set alarm points alert at: 70 ppm after 60 to 240 minutes; 150 ppm after 10 to 50 minutes; and 400 ppm after 4 to 15 minutes. Flush or surface mount. Test functionality of electrochemical CO sensing cell. Connect to RJ45 or digital input sensor ports. Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Maximum cable length: 1000 ft (305m). LED indicators for operation status and system test. Powered by ENVIROMUX-2D/5D/16D. Regulatory approvals: UL.
-
Product
0-600 Amp Variable Carbon Pile Load Tester
6039
-
• Test batteries up to 1200 CCA• Fine threaded shaft for fine adjustment• Temperature compensation chart• Easy to read digital voltmeter & ammeter combine with the versatility of a carbon pile load• Spring loaded to shut-off automatically• Unique curved discs to prevent hot spots• Tests all battery types• Made in USA of US and Global Components
-
Product
Carbon Fibre Beam Gauge
-
Designed to measure both internal and external diameters and lengths, the high modulus carbon fibre beam is stiff, lightweight and has an extremely low co-efficient of thermal expansion (CTE). Suitable for measuring high accuracy diameters and lengths up to 4000mm+.
-
Product
Carbon and Sulfur in Inorganic Materials by the Combustion Infrared Detection Technique
844 Series
-
LECO combined our customers' feedback with innovative engineering to develop the CS844, an elemental analyzer designed for wide-range measurement of carbon and sulfur content of primary steels, ores, finished metals, ceramics, and other inorganic materials using the combustion technique. Our exclusive MS Windows®-based software, coupled with a boom-mounted touch interface, gives you complete access to instrument control, analysis settings, diagnostics, reporting, and more—without sacrificing valuable bench space.
-
-
Product
Diamond-Like Carbon: High-Performance Coatings for Extreme Applications
-
When durability matters, Diamond-Like Carbon (DLC) coatings deliver. Known for their hardness, low friction, and chemical resistance, DLC films are the go-to solution for protecting surfaces in high-stress environments: from precision mechanical parts to advanced semiconductor devices.
-
Product
Transmitter Monitors Carbon Monoxide
CO-R
-
The CO transmitter monitors carbon monoxide (CO) levels and is designed for the continuous monitoring of vehicle exhaust in non-hazardous areas. The CO uses a wide spectrum, long life electrochemical sensor to measure the amount of carbon monoxide in the environment. It is offered with an operating range of 0 to 125 ppm. Both the Room and Duct CO transmitters are offered in a standard NEMA 1 rated ABS Polycarbonate plastic enclosure. An optional NEMA 4X watertight and dust proof enclosure is only available with the CO room transmitter.
-
Product
Carbon / Sulfur Analyzer
ELEMENTRAC CS‑d
-
ELTRA's ELEMENTRAC CS-d is the only analyzer in the market for determination of carbon and sulfur in organic as well as inorganic samples. For this purpose, the ELEMENTRAC CS-d is equipped with both an induction and a resistance furnace (ELTRA Dual Furnace Technology), covering the full range of carbon and sulfur analysis.
-
Product
CO Carbon Monoxide Probe
HD320A2
-
HD320A2 is a probe to be used with the HD32.1 Thermal Comfort data logger.
-
Product
Platform for Identifying Strategic Opportunities for Reducing Whole-Life Carbon
Carbon First
-
Carbon First is an award-winning platform that helps you identify strategic opportunities for reducing whole-life carbon in the early planning and design phases of infrastructure projects or portfolios.It empowers users to act earlier on net-zero strategies by highlighting bespoke carbon reduction opportunities and helping you set accurate Key Performance Indicators. It runs and compares multiple options on a visual dashboard quickly and easily, empowering companies to act effectively on net-zero goals and regulatory requirements.This digital innovation enables front-end loading in project planning, helping projects and portfolios be more successful and efficient across entire life cycles. Carbon First harnesses the highly respected Institute of Civil Engineer’s’ (ICE) Project 13 principles in infrastructure delivery, especially within digital transformation. These principles are designed to boost delivery productivity and certainty, improve whole-life outcomes, and support a more sustainable, innovative, highly skilled industry.
-
Product
Carbon Monoxide Detectors
Inspector CO Detectors
-
Sensorcon, Sensing Solutions by Molex believes in the importance of a dependable gas detector. Featuring proprietary engineering & software, our Inspector Series utilizes electrochemical sensors for fast & accurate measurements of CO.
-
Product
High Carbon Process Carrier Pallets
Composite Family
-
High Strength, high temperature, semiconductive composite board designed for use as circuit board and flex circuit carrying pallets for solder reflow ovens.
-
Product
Ultra-Low Range Gas Filter Correlation Carbon Monoxide Analyzer
Model T300U
-
The Model T300U Trace-level CO analyzer has been developed specifically to address the challenges of low level monitoring as required, for example, in the US NCore network. Using IR absorption with a Gas Filter Correlation Wheel, the T300U is designed to allow ultra-sensitive CO measurements while still meeting the requirements for use as a US EPA compliance analyzer.The optical bench is enclosed in a temperature controlled oven, dramatically decreasing instrument noise and drift. The objective and field mirrors in the sample cell are gold plated to maximize signal to noise performance, while a temperature-controlled Nafion dryer on the inlet minimizes water interference caused by ambient humidity changes. Periodically, the T300U seamlessly corrects its baseline by routing the sample through a heated catalytic CO scrubber. This Auto Reference function corrects zero drift and reduces the effect of interferences.All T Series instruments offer an advanced color display, capacitive touch screen, intuitive user interface, flexible I/O, and built-in data acquisition capability. All instrument set up, control and access to stored data and diagnostic information is available through the front panel, or via RS232, Ethernet, or USB com ports, either locally or by remote connection.The Model T300U comes with NumaView™ Software. NumaView™ Remote PC Software allows for a remote connection with virtual interface and data downloading capability to analyzers operating NumaView™ Software.
-
Product
Carbon Monoxide Detector Tester
Solo C3
-
Many multi-sensor fire detectors detect carbon monoxide (CO) as well as smoke and / or heat. Under international codes and standards the CO cell needs to be functionally tested with a CO stimulus from the protected area through the detector vents to the sensor.
-
Product
Carbon Monoxide Meter
ET110
-
The ET110 is an easy-to-use meter that detects and measures concentration levels of carbon monoxide (ppm) and temperature (oF/oC) making it the perfect choice for HVAC professionals. Backlit display with CO measurements (0 to 1000 ppm) and temperature (°F/°C ).
-
Product
IR Carbon and Sulphur Analyzer
LD-LCSA-A10
-
IR Carbon and Sulphur Analyzer LD-LCSA-A10 is a unit for determination of sulphur and carbon equipped with two treatment units including a high frequency induction burner and flexible temperature settings with automatic control. With an analysis time of 20 to 100 seconds and a sensitivity of 0.1 ppm the multi-shielded isolation circuit prevents the machine for high frequency interference. High speed 24-bit sampling improves sensitivity and accuracy.
-
Product
High Frequency Infrared Carbon and Sulfur Analyzer
CS-8820
-
Wuxi Jinyibo Instrument Technology Co., Ltd.
Infrared detector with low noise, high sensitivity and high stability. The modular design of the whole machine improves the reliability of the instrument. The electronic balance is automatically connected. WINDOWS full Chinese operation interface, easy to operate, easy to master. Dynamic display of various data and carbon in the analysis process. Measuring linear range is wide, and can be expanded. High-frequency circuit design is reasonable, high-frequency furnace power is adjustable, suitable for different material sample analysis requirements. The automatic cleaning device of the burner can reduce the influence of dust on the analysis results. The burner heating device makes the conversion rate of sulfur tend to be consistent, which improves the stability of sulfur determination. Measuring linear range is wide, and can be expanded. The software is fully functional, providing more than forty functions such as file help, system monitoring, channel selection, mathematical statistics, result correction, breakpoint correction, and system diagnosis.
-
Product
Elemental Analyzers for Carbon, Sulfur, Oxygen, Nitrogen and Hydrogen
-
HORIBA Scientific provides inorganic elemental analyzers for a wide range of applications based on the inert gas fusion technique and high frequency heating combustion in oxygen stream.The EMIA Series for Carbon and Sulfur analysis and EMGA Series for oxygen, nitrogen and hydrogen analysis strongly rely on HORIBA’s experience as a pioneer in Non-Dispersive Infrared (NDIR) technology. Both EMIA and EMGA designs meet all requirements for the metallurgical industry. These instruments also help scientists working in other application fields such as semiconductor, battery materials, ceramics and more.
