Firmware
-
product
For Conduction Cooled ΜTCA Chassis
UTC003
The VadaTech UTC003 is the most feature-rich MCH (MicroTCA Carrier Hub) for the Conduction Cooled μTCA chassis in the market. It’s management software is based on VadaTech’s proven Carrier Manager and Shelf Manager. The MCMC manages the power modules, the two CU (Cooling Units) and up to 12 AMCs within the μTCA chassis. It also interfaces to and manages the on-board fabric interfaces. The module is available with PCIe, SRIO, 10GbE Layer 3 managed, and GbE Layer 2 managed. The UTC003 runs Linux 2.6 on it’s MCMC CPU and is hot-swappable and fully redundant when used in conjunction with a second instance of the module. The firmware is HPM.1 compliant which allows for ease of upgrade. The UTC003 provides Fabric (100 Mhz HCSL) clock to each AMC.
-
product
Automatic Antenna Tuner
Automatic Antenna Tuner has not been released for full Beta testing and production yet as we are solving some firmware issues. We cannot give you a date nor estimate at this time when full production will commence.
-
product
Modbus TCP Gateway
SI-485MB
SI-485MB is a Modbus gateway to convert bi-directionally Modbus RTU/ASCII of serial interface to Modebus TCP of Ethernet. The firmware for gateway process supports Modbus TCP master mode and Modbu TCP slave mode and supports all the current ModbusRTU/ASCII register and command conversion. The robust metal body, broad range of temperature, wide input voltage range, and the support for installation by options such as 35mm DIN rail and wall bracket allow you to use it for factory automation without worry.
-
product
Test RTM with Ethernet SFP
VR300
Sundance Multiprocessor Technology Ltd.
The VR300 is a Test RTM, typically used during firmware and software development and debugging cycles on the VF360. The rear panel contains two mini-USB connectors, a Dual mini-SAS (SFF-8088) connector and a SFP case.
-
product
Cable Modem Test Platform
Promptlink Communications, Inc.
CMTP has broad support for the mixed environment of DOCSIS 3.0, and earlier devices. Similarly, it supports all DOCSIS/Euro DOCSIS equipment vendors, impartially treating each vendor's devices with maximum performance and minimum hassle.CMTP is fully automated, requiring no user input for testing.CMTP tests the basic Cable Modem, Wi-Fi and EMTA parameters such as signal levels, signal to noise ratio, etc. as well as device throughput and packet loss. For PacketCable devices, CMTP tests each phone port individually, with maximum functionality being tested.CMTP can also be configured to upgrade the firmware of the devices in a multi-step and conditional process.
-
product
Test system for Electronic Device
PCB
The main focus of the test system is validation and functional testing of electronic devices. The tests include electrical parameters and logical functions of the firmware. Device groups can be stimulated externally and output signals can be acquired by the test points on the board. Limits and ranges of the acquired signals can be monitored and stored for verification.
-
product
ProBus Probe Adapter for TekProbe-BNC Probes
TPA10
- Allows TekProbe interface level II probes to work with any ProBus-equipped Teledyne LeCroy oscilloscope- Automatic probe detection- Provides all necessary power and offset control to the attached probe- Supports probes up to 4 GHz- Easy firmware updates- Wide variety of probes supported including: Preamplifiers, Current Probes, Single-Ended Active Probes and Differential Active Probes
-
product
Grid-EYE® Unit Infrared Array Sensor
Panasonic Industrial Devices Sales Company of America
Panasonic is pleased to announce the availability of the Panasonic Grid-EYE® Infrared Array Sensor Unit. The Grid-EYE Unit combines four Grid-EYE Infrared Array Sensors to increase the detection area up to 3.8m squared. The Grid-EYE Unit comes preloaded with firmware capable of detection and counting up to 8 people within this area and while they are in this area it can track their direction of movement. The Sensor transmits this information via RS485 using Modbus protocol.
-
product
Serial To Digital Interface Boards
*ICS's Serial to Digital Interface boards provide the user with digital IO signals that can be user configured to match virtually any application. Both boards are available with high power relay drivers and with optional firmware designed to simplify switching applications.*All boards are designed for mounting inside a chassis.
-
product
Software
A tool is available to update ARGUS testers, which is also included in our WINplus and WINanalyse software packages. With this tool, the latest firmware versions can be downloaded to the tester from www.argus.info. The whole procedure is very simple and intuitive, thanks to the integrated step-by-step instructions.
-
product
Bridge Devices
USB
*Royalty free Virtual Com Port (VCP) drivers*Simple GUI based Xpress configurator for configuring, programming and customizing applications*No USB expertise required*Seamless compatibility with most operating systems*UART, SPI, I2C/SMBus and I2S interface options available*Fastest way to add USB Turn key, no firmware development needed
-
product
Upgrade For Star SAFIRE® 380-HD and 380-HDc
380X Upgrade
The Star SAFIRE® 380X is a hardware, firmware, and software upgrade to support advanced image aiding features for our globally renowned Star SAFIRE 380 gimbal systems, including Star SAFIRE 380-HD and 380-HDc. The new 380X skillet upgrade reduces operator workload for faster, smarter decision support and features customizable configurations for multi-tile video management and visual user interface, and touchscreen and streaming tablet support. It also features an integrated moving target indicator (MTI) and de-scintillation filter, that removes atmospheric effects to reveal clearer, sharper detail from greater distances.
-
product
Firmware for High-speed Communication
OP-FW12GA
OP-FW12GA is the firmware to increase the speed of monitoring test of bit synchronous communication (such as HDLC/SDLC/X.25, or CC-Link communication), SPI communication, Profibus-DP (field bus known for high-speed communication), UART (asynchronous communication, which is commonly used). By processing great part of monitoring processes by FPGA, it unfailingly captures communication data with time stamps of a microsecond rate. The interface supports RS-232C/RS-422/RS-485/TTL.
-
product
PXIe System Sync Module, 2 Port
M9032A
The M9032A has a Soft Front Panel (SFP) that provides a graphical user interface to the system sync module. It allows the user to set up the most commonly used functionalities of the module. The SFP also gives you the ability to check the module's connection status, configure the reference clock and IO settings, and perform firmware udpates.
-
product
Chassis - Controls up to 16 8x1 Modules, 32 4x1 Modules or Mixtures or 8x1's, 4x1's, 2x1's and 2x2 Modules in Any Combination or Configuration up for up to 128 Relay Drives
CXM/128-MF
These Chassis controls up to 16 8x1 modules, 32 4x1 modules or mixtures of 8x1"s, 4x1"s, 2x1"s and 2x2 modules in any combination or configuration for up to 128 relay drives. LEDs on the front panel show switch and power status. Add Switch Modules, display / driver modules and a Control Module to complete the system or simply buy the chassis wired out to D connectors to control your own relays. A manual control is optional. Chassis is available with sink or source relay drivers from + 5 to + 28 volts, ot TTL drivers for programmable attenuators. Firmware commands for Fade and Handover for WiFi, Cell Phone and WiMax labs. Fully custom systems built with little to no NRE.
-
product
USB Connectivity Bridges
USBXpress
Silicon Labs USBXpress devices are highly optimized solutions that enable designers to easily add USB to existing and new applications. These fixed function devices provide the easiest method to add USB without the need for any firmware or driver development. USBxpress portfolio supports several USB to serial bridge devices including human interface (HID) devices and USB Audio devices.
-
product
Master Controller
RatMaster
- Jumper free configuration- Intuitive configuration software- RS-232, TTL and CI-V interfaces- Automatically generates Icom CI-V data stream from non-Icom radios- Configurable band limits- Built-in USB interface- Set default antenna per band- Field upgradeable firmware- Anodized aluminum case- Laser engraved panels
-
product
Dielectric Material Test Fixture
16453A
The 16453A is designed for accurate dielectric constant and loss tangent measurements on the E4991A/4291A/B. It employs the parallel plate method, which sandwiches the material between two electrodes to form a capacitor. The E4991A/4291A/B measures the capacitance created from the fixure, and option 002 firmware calculates the relative complex permittivity as described in the 16451B. Adjustment to insure parallel electrodes is required when using the 16451B. This adjustment is not required with the 16453A because the fixure has a flexible electrode that adjusts automatically to the material surface.
-
product
Development
If possible we use standard market instruments and components. However not every task can be solved technically and economically reasonable. That is when our development department comes to place. Our colleagues already developed many approaches from little, practicable assemblies up to holistic measurement features. These solutions are customer oriented and together with a special firmware this is often a useful solution.
-
product
DAQ Modules
Q.series X DAQ Modules for Ethernet, CAN and ProfiNet
All Q.series X DAQ systems possess the same measurement capabilities and performance, regardless of form factor. The main differentiating quality between the XL and XE versions of Q.series X is the Fieldbus communication protocol (Localbus or EtherCAT), which can be interchanged on Q.series X modules using a simple firmware update.
-
product
High Performance Programmable AC Power Source
61500 Series
Chroma 61500 Series have built in 16-bit measurement circuits and firmware utilities to measure the true RMS voltage, current, true power, apparent power, reactive power, power factor, current crest factor, and inrush current.
-
product
Software / Firmware
You can connect to our Ethernet test box right now and send/receive remote commands. It is located at fixed IP address 104.63.176.50 (tcp port 3001). The most often asked question about our test systems is “How easy are they to remotely control”? So we built up a test system and put it on an outward-facing IP address so that any of our customers can interact with our firmware.
-
product
PXIe High-Speed Digitizer/ Wideband Digital Receiver, 12-bit, 3.2 GS/s, FPGA Signal Processing
M9203A
The Keysight M9203A is a low noise, 12-bit PXIe high-speed digitizer/ wideband digital receiver with programmable on-board processing. With a wide analog bandwidth, this high-speed digitizer is ideal for applications requiring wideband signal capture and very high dynamic range. The M9203A is a dual-slot 3U PXIe 12-bit wideband digital receiver running at 3.2 GS/s, up to 2 GHz instantaneous analog bandwidth and providing a large 4 GB DDR3 acquisition memory. The M9203A features a large XilinxFPGA that can implement different functionalities depending on the selected firmware option. Dedicated functions can also be implemented on board, allowing support of various applications. Furthermore, Keysight is supporting the deployment of custom processing algorithm on this digitizer with the U5340A FPGA development kit. Integrating algorithms minimizes the need for additional circuitry and exploit the full density and speed of the digitizer.
-
product
Cable Plant Monitoring
Promptlink Communications, Inc.
Cable Plant Monitoring (CPM) is a real-time network device management tool for your DOCSIS network. CPM handles all of your DOCSIS cable modems, Wireless CMs, eMTA and Cable Modem Termination Systems (CMTS) along with monitoring fiber nodes. This allows you to readily see network problems, troubleshoot customer access issues, and easily deal with difficult management efforts, including upgrading CPE firmware on a very large scale.
-
product
Development Platform
NFC/WLC
CISC is offering various technology elements to support the design of NFC-based WLC (wireless charging). These pre-tested hardware modules including various antenna sizes, firmware, and software support customers to quickly have available solutions for their requirements. Customization helps in particular for very challenging application requirements. Customers benefit from very fast time to market for WLC solutions.
-
product
DC Bias and RF Stimulus Control Module
Quantum SMART Fixture
Accel-RF Corporation, the world leader in turnkey RF automated reliability test instruments, has "unplugged" the industry-leading RF SMART Fixture from their automated test platform and made it available for benchtop test. The NEW Quantum SMART Fixture is a programmable self-contained DC bias and RF stimulus control module capable of synchronizing sequenced independent pulsed-bias and pulsed-RF signals to a DUT or remote fixture. The signals are controlled from a user interface compatible with Accel-RF's LIFETEST software. The Quantum SMART fixture is capable of "active" temperature control and monitoring of a remote DUT through embedded firmware in the microprocessor
-
product
Software For Transformer Measuring Lite
T-Base Lite
T-Base Lite is intended for users preferring simplicity over complexity of the Pro version. It is limited to the basic functions of USB interface, data import, data export, synchronization, and automatic firmware updates. Data can be exported in many popular data formats such as Excel, Word, text, .csv, .xml, Crystal reports, and .html. Measurements can be saved as archive files and imported into the database of the T-Base Pro version.
-
product
SLCAN API
SLCAN stands for "Serial CAN Protocol" and is a simple ASCII protocol for communication with USB-CAN adapters. This protocol has established itself as the standard, especially for inexpensive CAN adapters. We offer special firmware (SLCAN firmware) for our Tiny CAN modules I and II for using this protocol.
-
product
64 Ch Peak Sensing ADC
V1741
The V1741 is provided with drivers for the supported communication interfaces, C libraries, demo software for an easy board understanding. Firmware upgrade can be performed via optical link or VMEbus by the user.
-
product
ANSI X3.28 Interface Board
Model 4804B-7
* F30145 firmware converts printable ASCII character strings into the ANSI X3.28 serial protocol.* User selectable single-ended RS-232 and differential RS-422/RS-485 serial signals.* Can be used to replace obsolete ICS 4814 Interfaces.* Connect to the rear panel with a GPIB Flat-ribbon cable or with a GPIB Connector/Address Switch Cable.* Runs on 5 Vdc regulated or 5.5 to 15 V unregulated power.
