-
Product
Universal Transmitter
-
Knick Elektronische Messgeräte GmbH & Co. KG.
Universal Transmitter for temperature, load cells / strain gauge, potentiometer and resistance in 6 mm housing. Functional safety up to SIL 2, SIL 3 redundant to parameterization via interface or intuitively, directly on the device. Universal use with 24 V DC or AC power supply.
-
Product
Low Voltage DC / Battery Powered High Voltage Amplifiers
WMA-005 And WMA-005LF
-
The Falco Systems WMA-005 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-005LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
Product
FAult Detector and OScilloscope 9 Functions in 1
FADOS9F1
-
Prot-Ar-Ge Industrial Project Design R&D Ltd. Co.
2 unique features are added to the FADOS9F1 over the FADOS71. First feature is the Programmable DC Power Supply; It can be adjusted between 0-16V and 20-1500mA with power output; the DC Voltage/Current graphs of the electronic card power supply can be produced. The second feature is the “IR Remote Temperature Measurement Sensor”; this sensor is used to find the components that heat up by drawing too much current. Using these two features together may reduce the time for trouble shooting some malfunctions by 5 to 10 times. These features can be used as a new technique for trouble shooting.
-
Product
PXI Prototyping Module, 2-Slot, 78-Pin D-Type
40-225A-402
Prototyping Module
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
-
Product
Under/Overvoltage Monitors
-
Contacts to control an external horn or light, or to signal your PLC are now available on independent accessories for any power supply. These modules can be used on power supplies with DC voltages from 5 to 125 Vdc. SPDT relay contacts switch if the power supply’s output deviates by:*1.0 volt or more (for 5 volt outputs)*2.0 volts or more (for 6 to 48 volt outputs)*3.0 volts or more (for 49 to 125 volt outputs)
-
Product
Powered VME64x Crates
9U VME64x 6023
-
The WIENER VME 6023 crate series is the newest generation of 19" integrated packaging system for VME/VME64 bus systems with 9Ux400mm cards. Designed primarily for applications in data acquisition, control and test instrumentation it combines superior mechanical quality with lowest noise power supply technology.
-
Product
Master Reference Generator
Mentor
-
Precision Time Protocol IEEE-1588 PTP grandmaster• Multiple video and audio formats in one box• Simultaneous 525/625 and HD Tri Level Sync outputs• Highly accurate GPS reference for synchronisation and timecode• Vector web-browser setup and monitoring tool• Redundant PSU option• Add upgrades and options without return to factory• Generates synchronised audio and video• Redundant units with changeover• 4K test pattern ready (future upgrade)
-
Product
Power Supplies
V-400
-
The V-400 power supplies are durable, practical, and efficient. Remove all superfluous attachments and features. The V-400 can provide reliability and 400 watts of power you can depend on to run your system. With its 80mm silent cooling fan designed for fastest cooling time and minimal noise level; you won’t have to worry about overheating and noisy fans anymore. This is the basic power supply for casual users who just needs something that is cost effective and works.
-
Product
ACDC
SQ Series
-
The SQ Series boast over a decade of reliable, field proven service and are the recognizedindustry standard for high performance AC/DC power supplies.
-
Product
PXI Prototyping Module, 1-Slot, 96-Pin Micro-D
40-225A-101
Prototyping Module
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
Phase Noise Tester 5MHz to 40GHz
Model 7340
-
Berkeley Nucleonics Corporation
Broad Frequency Range in a single compact instrument from 5MHz to 40GHz. Measurement offsets from .01Hz to 100MHz. Absolute Phase Noise - High Drift mode (ability to measure modulations, high drifting or unstable DUTs, etc.). AM (Absolute Amplitude Noise) measurements. Pulsed Measurement Capabilities. Transient Mode: measure WB Frequency, NB Frequency, NB Phase, NB Power (WB/NB being Wide Band and Narrow Band). Dual channel low-noise integrated power supplies.
-
Product
H.V. Probe Meter
PD-40AM
-
Standard Electric Works Co., Ltd
● Measures positive polarity DC voltages up to 40kV.● Lightweight and rugged.● 2 available contact tips: round needle tip for normal use and a special flat spring-type for CRT anode.● Are typically used to measure high voltages in TV sets, power supplies and instruments in laboratories.
-
Product
EDFA
SPA-10G-32
-
Hangzhou Softel Optic Co., Ltd.
*Single/dual input for choice, built in optical switch for dual input, the switching power can be set by thebutton in the front panel or by web snmp. *Output adjustable by buttons in the front panel or web snmp, the range is down 4dBm *Max multi 32 port, with built in1310/1490/1550/1270/1577/WDM,max total output 38 dBm *Standard RJ 45 port for remote control, we can provide output contract and web manager for choice, and also plug-in snmp hardware can be reserved for update. *With laser key to turn on/off the laser.*With RF test function. *Adopts JDSU Pump laser*Led displays the working condition of the machine*Dual power hot plug power supply for choice, 90V～250V AC or -48V DC
-
Product
GPIB User Installable Interface Module
E363GPBU
Interface Module
Add a GPIB interface to your E36300 Series triple output or E36200 Series autoranging bench power supply.
-
Product
Calibrator, Calibrated w/Data, Current, 185 mm, 78 mm, 38 mm
72-6694 CAL D
-
The 72-6694 CAL D from Tenma is a current calibrator. It provides quality and accuracy of handheld calibrator of precision current source. It features large LCD display (maximum display counts 1999, 13mm (0.5") digit size). The current calibrator has 006P DC 9V, MN1604/PP3 battery or equivalent alkaline type or heavy duty type power supply. The dimension is 185mm × 78mm × 38mm (7.3" × 3" × 1.5") and weight is 265g/0.58lb (including battery). It has adjustable 0 to 24mA current source, 2 ranges (0 to 19.99mA (0.01mA display resolution, ±(0.25% FS + 1d) accuracy), 0 to 24mA (0.1mA display resolution, ±(0.5% FS + 1d) accuracy).
-
Product
Test System
ITC57300
-
The ITC57300 Dynamic Parametric Test System mainframe accepts Test Heads that perform nondestructive transient measurements on semiconductor devices such as Insulated Gate Bipolar Transistors (IGBT), power MOSFETs, diodes, and other bipolar devices(requires additional optional bias power supplies and custom personality boards). Included in the mainframe are all test equipment and software necessary to analyze and perform resistive and inductive switching time, switching losses, gate charge, Trr/Qrr, and other transient tests.
-
Product
Multipurpose Module for SLSC
Module
Bloomy’s Multipurpose Module for SLSC provides a convenient location in an SLSC system for applications ranging from a simple rearrangement of signals to installation of circuits and components. Both front panel connectors are mapped to screw terminals, through holes, and surface-mount technology pads thus accommodating a wide variety of components. Breakout areas for all rear transition interface (RTI) pins simplify integration into SLSC-based systems. On-board power supplies (±15VDC, +5V, and +3.3V) are also made available for the user’s analog and digital circuits. The module features a considerable amount of available board space for user applications.
-
-
Product
Gunn Diodes
-
The Gunn diode is the best known and most readily available device in the family of transferred electron devices (TED). They are employed as DC to microwave converters using the negative resistance characteristics of bulk Gallium Arsenide (GaAs) and only require a standard, low impedance, constant voltage power supply, thereby eliminating complex circuitry. Teledyne Lincoln Microwave’s DC1200 series of GaAs Gunn diodes is designed for operation at fixed frequency (determined by the oscillator cavity) within a specified band under CW or pulsed conditions.
-
Product
Variable Frequency AC Power Supply 500VA 1KA 2KVA 3KVA 5KVA
CX-9000
-
Shenzhen Chuangxin Instruments Co., Ltd.
Variable Frequency AC Power Supply 500VA 1KA 2KVA 3KVA 5KVA
-
Product
Saturable Reactor Inductors
-
Osborne Saturable Reactors are designed to provide a variable output voltage through the use of variable impedance connected in series with a constant impedance load. Each saturable reactor’s impedance is determined by the application of DC power to a control winding. As the level of power supplied to the control winding is increased, the saturable reactor becomes more saturated. This reduces the impedance of the AC gate winding, and increase the amount of the supply voltage that is transferred to the load. Conversely, as the power is reduced to the control winding, the reactor becomes less saturated, the gate winding has more impedance and less of the input voltage is provided to the output impedance. This approach provides excellent quality, reliability, and control when designed to match the requirements of a specific application.
-
Product
LilyPad Arduino USB
ATmega32U4 Board
-
This is the LilyPad Arduino USB board, controlled by an ATmega32U4 with the Arduino bootloader. It has a built in power supply socket and an on/off switch with the only extra piece of hardware you need to program the LilyPad USB is a micro-USB cable, since the new IC has built-in USB support. Any of our LiPo batteries can be plugged right into the JST socket to provide you with easy, on-the-go power. That LiPo battery is even rechargeable through the board, no more special external LiPo chargers required!
-
Product
200 MHz, 3.5 pF, 1 MOhm Active Differential probe
ZD200
-
With the ProBus interface, the ZD200 becomes an integral part of the oscilloscope. The probe sensitivity and offset are automatically optimized based on the oscilloscope gain settings, so control is transparent to the user. When used with a LeCroy digital oscilloscope, no external power supply is required.
-
Product
Picosecond-Diode Lasers for Spectroscopy
-
Designed and manufactured by Becker & Hickl – bh delivers prominent picosecond diode lasers with wavelengths from the NUV to the NIR. All bh pulsed diode lasers work with simple +12V power supply or pull their power from the USB port of a PC or Notebook Computer. Other features are high repetition rate, short pulse width, unprecedented timing and power stability, and extremely low electrical noise level.
-
Product
Power Supplies
RM - SERIES
-
With dual PCI-E connectors, the RM Series carries all its essentials to power your system. Enjoy the graphic rendered programs and games without the threat of overheating. Its dark aluminum chassis not only looks good, but dramatically relieves heat built-up. The 120mm cooling fan enhances the already efficient heat dissipation rate and helps balance the cooling system with noise level. The RM Series is great for high end users to everyday casual users. Whatever your system needs, the RM Series can deliver.
-
Product
Power Supply POWERLAB 305D
-
high precision current sources with variable voltage and current over the entire range . They can operate in different modes of stabilization voltage or current switched automatically with adjustable limit value of the load current at any point in the range.
-
-
Product
Inductors
-
Murata offers a broad lineup of chip inductors that fit diverse requirements such as compact size, large current, etc. across applications ranging from consumer use to automotive applications that require high reliability. We are also productizing inductors with superior mountability thanks to their SMD type that are suited to specific applications such as high-frequency circuits, power supply circuits, in-vehicle PoC, short-range wireless communication, etc.
-
Product
DC Power Supply
◎PW-4063R
-
*Use Toroidal Transformer. Low EMI & High EMS.*Triple output, 0-32V/0-6A X2 and 5V/3A .Max. 400Watts*Tracking operation. Max. output 64V/6A on tracking series or 32V/12A on tracking parallel.*4 display, Green LED shows Voltage and Red LRD shows Current. Easy to read.*Compact design. G.W. 9Kgs only. Easy to handle.*The resolution of PW-4063R as high as 0.01v and 0.001A.*Provide 4Pcs 10turns micro adjust VR for Voltage and Current adjustment. Easy to operate.*Very low Ripple & Noise, less than 0.4mVrms. Very suit for precise measurement.
