Can bus
Controller Area Network
See Also: Serial, I2C, LIN, ExpressCard, Fieldbus, FireWire, RS-232, RS-485, PCI Express, Serial ATA, Serial Peripheral Interface, SMBus
-
Product
Power ICs
-
Vishay Siliconix Power ICs include switching regulators, drivers, battery management ICs, and bus interface devices, as well as single-package microBUCK® converter and DrMOS solutions.
-
Product
PCI Bus Analog Output Board, 8 Isolated Outputs, 14 Bit
APCI-3501-8
-
*8 analog output channels*Optical isolation 500 V*Settling time 30 µs typ.*14-bit resolution (13 bit for 0-10 V)*Output voltage: ±10 V, 0-10 V (switchable through software)*Output voltage after reset: 0 V*Each output channel has its own ground line (without optical isolation from the others)*Driver capacity: 5 mA/500 pF*Short-circuit protection, EMI filters*Noise neutralization of the PC supply*Creeping distance: 3.2 mm acc. to DIN VDE 0411-100*Watchdog for resetting the analog output channels (4 different time units: µs, ms, s, min) or as 12-bit timer (with interrupt possibility), when the watchdog function is not necessary*2 digital input channels, 24 V, isolated*2 digital output channels, 24 V, isolated
-
Product
3-slot ATX-supported 1U Butterfly PICMG 1.3 Bus Passive Backplane
FAB209
-
*Designed for PICMG 1.3 SBC*Compatible with AX61120TP chassis*Supports one PICMG 1.3 CPU card slot, one PCIe x4 slot and one PCIe x16 slot
-
Product
Multiplex Bus Switch
MBX1553
-
Curtiss-Wright Defense Solutions
The Curtiss-Wright MBX1553 Multiplex Bus Switch enhances almost any MIL-STD-1553 system by providing a "virtual patch panel" housed in a 19" rack-mountable 1U chassis. The MBX1553 eliminates time-consuming bus rewiring between different avionics simulations and test scenarios.
-
Product
LXI WTB Terminator, 90.6 ohm
60-983-002
Terminator
The 60-983 is an LXI compatible Wired Trigger Bus Terminator (WTB) designed to be attached to the end of a WTB cable. The LXI WTB uses a transmission line cable to connect LXI devices together that support the WTB capability of the LXI standard. Like all transmissions it needs to be correctly terminated to avoid reflections that could change the signal amplitude along the cable and generate timing jitter or trigger errors. The 60-983 is a simple terminator that can be placed at each end of the WTB chain to correctly terminate the transmission line with minimal reflections.
-
Product
Universal Test System
LS6601A
-
LS6601A Universal Test System is based on LXI bus, primarily used for functional electronic product or system verification, test parameters. Because the system design is based on LXI bus structure, so its addition to general characteristics of versatility, scalability, but the architecture of the system more flexible, the test system is not limited to one or more cabinets, but may be needed test network and multiple LS6601A and can be easily grouped into one or more of the ground test system, depending on the test mechanism, form a powerful set of test, control, simulation, simulation, data management as one; distributed in different places .
-
Product
Controller Card
GPIB-PCI-XL
Controller
The GPIB-PCI-XL is a flexible PCI GPIB controller card that converts any PC with a PCI bus slot into a GPIB controller.
-
Product
Intelligent Mini Munitions Store Interface (MMSI) Module for Excalibur 800 Family of Carrier Boards
M8KMMSI
-
The M8KMMSI is an intelligent, Mini Munitions Store Interface [MMSI] module for the multimode, multiprotocol, Excalibur 8000 family of carrier boards. Each module of the M8KMMSI contains 64K bytes of dual-port RAM for Data blocks, Control registers, and Look-up Tables. All Data blocks and Control registers are memory mapped and may be accessed in real time. Each M8KMMSI module may be programmed to operate in one of three modes of operation: Remote Terminal, Bus Controller/Concurrent-RT/Concurrent Monitor and Bus Monitor.The M4KMMSI comes complete with Windows software, a C-driver software library including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application.
-
Product
2-Channel 500 MHz A/D and 2-Channel 800 MHz D/A with Virtex-6 FPGA - 3U VPX
Model 52650
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Supports gigabit serial fabrics including PCI Express, Serial RapidIO and Xilinx Aurora- Two 500 MHz 12-bit A/Ds- One digital upconverter- Two 800 MHz 16-bit D/As- Up to 2 GB of DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- 3U VPX form factors provides a compact, rugged platform- Compatible with several VITA standards including: VITA-46, VITA-48 AND VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Eurocard Plugbord
E220-6U-2
-
VECTOR Electronics and Technology, Inc.
6U x 220mm Eurocard size for 96-pin DIN connectors. Voltage and ground buses around board perimeter on both sides. Bus surfaces solder coated for user convenience. For solder, Wire-Wrap or mixed wiring methods. Row and column legends provided.
-
Product
Differential Active Probe, 1.7 GHz
DP0013A
Signal Probe
The Keysight DP0013A is the 1.7 GHz model of the DP001xA Series differential active probes. These provide the superior general-purpose differential signal measurements required for many of today’s high-speed power-related measurements such as motor drives, automotive differential bus measurements, and high-speed digital system designs.
-
Product
AMC GBit link card/VITA 57 FMC carrier
SIS8100
-
The SIS8100 will be a single width mid height AdancedMC card. It will interface with a single PCI Express lane over a PLX Technology PEX811 PCI Express to local bus bridge chip and have an on board Virtex IV FPGA. The default stuffing option has a Small Form Factor (SFF) optical link medium that can be operated at 1, 2.5 and 4 GBit/s.
-
Product
Ethernet to GPIB Controller
Model 9065
-
* Controls GPIB Devices anywhere there is a network or internet connection.* No special driver required which eliminates driver problems. * Controllable with Windows PC programs like C, Visual Basic, LabVIEW, VEE, etc that make VISA or SICL calls.* Controllable from MAC/UNIX/LINUX and similar computers with RPC calls.* Fully VXI-11 compliant. * Includes ICS's VXI-11 and VISA keyboard control programs. Control instruments without a program. * Works with Agilent, NI and Kikisui VISA libraries.* Internal webserver lets you change network settings from any browser.* Network connectivity eliminates GPIB Bus Extension problems.* Allows multiple users to access the GPIB instruments.* Supports GPIB and HP-IB 488.2 complicant instruments.* 9065 is a 2nd generation drop-in replacement for ICS's Model 8065. The Model 9065 is 2x to 4x faster and includes a webserver instrument control page.
-
Product
PXI 8 Slot BRIC Module, 1 Resource Distributor, 4 Bus Matrix Inputs
40-569B-114
Matrix Switch Module
The 40-569B is a range of high-density BRIC matrices capable of switching up to 2A and up to 200VDC/180VAC. These large PXI matrix modules are available with multiple configurations in 4 or 8 slot sizes and are constructed using high-quality electromechanical relays. The 40-569-114 is a 8 slot module fitted with 4 Bus Matrix Inputs cards and 1 Resource Distributor card.
-
Product
Flight Line Avionics Test
-
The TS 717 Test Set for ARINC 717 is a convenient, easy-to-use tool for test and maintenance of aircraft systems that are tied to the Digital Flight Data Recorder (DFDR). The compact interface/cable hardware is conveniently stored in a rugged carrying case for easy transport and quick deployment.The webFLT™ is a wireless functional tester for aircraft systems using the Digital Flight Data Recorder ARINC 717 bus. It connects directly to the aircraft system test plug and transfers data to the test computer via an 802.11 b/g wireless link, eliminating cabling in the crowded cockpit that can be tripped over or damaged.
-
Product
PCI Module
PCI-IPC
-
The PCI-IPC module provides a high performance flexible I/O scheme, that supports industry standard Industry PacksÔ. For application requiring low cost, high density I/O or unique combinations, the PCI-IPC is the perfect solution.The Local DSP can be used to simply move data to and from the PCI bus or provide pre processing functions such as local PID controls, FFT’s, digital filtering, etc. Custom application software can be downloaded to the DSP via the PCI bus.
-
Product
3U Processor Board
CP39001
-
LinkedHope Intelligent Technologies Co.,Ltd.
CP39001 is a 1553B bus control card developed by Linghao Intelligent® for avionics applications. The product complies with the PICMG 2.0 R3.0 specification. CP39001 uses DDC's BU-61580 1553B bus protocol control chip and TI's DSP as the intelligent control unit.
-
Product
Avionics Test & Simulation Software
-
Ballard CoPilot® is an intuitive, graphical software program that allows you to easily monitor, record, replay, analyze, and simulate avionics bus data. With CoPilot you can interact directly with data on multiple buses using Ballard avionics interface hardware or work with previously recorded data. This advanced program features powerful tools for development, testing, troubleshooting and maintenance of avionics equipment and systems.
-
Product
8-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB208
-
The FAB208 has a PICMG 1.3 CPU card slot, one PCI Express x16 slot, and a total of six 32bit/33MHz PCI slots. The onboard 24-pin ATX power connector and 8-pin connector for thermal detected board are featured. Furthermore, the backplane supports two high speed USB 2.0 ports. The FAB208 is optimized to support AXIOMTEK's PICMG 1.3 system host boards, the SHB100 and SHB110. We have two enclosures, the AX60551 and AX60552, to house the backplane.
-
Product
Mini PCI Module
MPCI-1553-DDC
Controller
The ALPHI MPCI-1553-DDC uses the BU-65864 communication device as its 1553 bus controller, or remote terminal, or monitor terminal. A single controller has two redundant channels and built in transceivers. The controller has internal transceivers for both channel A and B. The Mini PCI board has on-board transformers for both channels. The board format is a Mini PCI boardlayout.
-
Product
Single or Dual DDC ACE 1553 Controller
CPCI-1553-DDC-1
Controller
Single or Dual DDC ACE 1553 Controller, Bus Controller, Remote Terminal, Bus Monitor Modes.
-
Product
Vegas Data Diode
01-09838
-
Non-ruggedized module that addresses concerns regarding use of untrusted, commercial-off-the-shelf (COTS) bus logging on aircraft with a MIL-STD-1553 or ARINC-429 bus interface.
-
Product
14-bit, 125 MS/s Waveform Digitizer
ATS9146
-
ATS9146 is a 2-channel, 14-bit, 125 MS/s waveform digitizer capable of storing up to 128 Million samples per channel of acquired data in its on-board memory or streaming acquired data to motherboard memory. ATS9146 is a single-lane PCI Express (PCIe x1) Gen 1 card, which supports up to 200 MB/s bus throughput. ATS9146 is an ideal solution for many applications.
-
Product
PXIe-6535, 32-Channel, 10 MHz, 40 MB/s PXI Digital I/O Module
780695-01
Digital I/O
32-Channel, 10 MHz, 40 MB/s PXI Digital I/O Module—The PXIe‑6535 can continuously stream data over the PXI Express bus. It's an ideal solution for interfacing and testing image sensors or display panels. The module is also well-suited for other common digital applications such as pattern I/O, change detection, protocol emulation, or other custom digital interfacing. It features selectable voltage levels and per-channel directional control of the digital lines.
-
Product
8-CH Relay Outputs & 8-CH Isolated DI PCI Cards
PCI-7250/7251
Relay
ADLINK's PCI-7250/7251 provide 4-CH SPDT (Form C) & 4-CH SPST (Form A) relay outputs and 8-CH isolated digital inputs. The status of each relay output is represented by an onboard LED. When the relay is in SET condition, its corresponding LED will turn ON, and on the contrary, it is OFF. All digital input channels are nonpolarity, optically isolated, and may be set to use RC filter or not. The devices are suitable for collecting digital inputs in noisy environments. The PCI-7251 is an 8-CH relay outputs and 8-CH isolated DI extension card of the PCI-7250. All the I/O functions of PCI-7251 are the same as those of the PCI-7250. The PCI-7251 has to be connected with PCI-7250 and the bus interface is controlled by the PCI-7250. Up to three PCI-7251 cards can be connected to one PCI-7250, therefore, expanding the PCI-7250's DIO from 8 DIO to maximum 32 DIO.
-
Product
Wide Band Filters (multi-octave)
ERF-5W™ Series (Single & Dual)
-
The new ERF-5W™ filter takes Pole/Zero’s MINI-ERF® technology to a higher level of RF power handling, with 5W (average) in-band power handling, and covering the entire military tactical radio tuning range of 30-520 MHz in one integrated package. This tunability is accomplished by the use of three poles of selectivity, multiple internal tunable filters along with high performance PIN diode RF band select switches. The tunable filters are designed to minimize size and power consumption, while maintaining high RF power handling and linearity characteristics. Serial control is accomplished via a standard Serial Peripheral Interface (SPI)-based bus.
-
Product
Single or Dual DDC ACE 1553 Controller
PCI-1553DDC-1
Controller
The PCI-1553-DDC uses Data Device Corporation’s ACE, DDC enhanced mini BU61865G4-290 communication device as its 1553 bus controller, or remote terminal, or monitorterminal.
-
Product
PCI Express® Bus To 3U PXI Express™ Chassis Expansion Kit
ACL-EXPRESS-3
-
The PCIe-to-PXIe expansion kit includes one PCIe-8560, one PXIe- 8565, and one ACL-EXPRESS cable (3 meters).
-
Product
1553Guard
-
MIL-STD-1553 bus architecture is a threat that adversaries can leverage to compromise your equipment and spread malicious software through your Serial Data Bus (SDB) system. You need a solution that can not only identify current and future cyberattacks in real-time but also instantly eliminate those threats before they wreak havoc and interrupt the mission.
-
Product
FlexRay Cable
-
FlexRay Cable connects FlexRay interfaces to devices, breakout boxes, other interfaces, and accessories. This cable meets FlexRay cabling specifications and is compatible with all NI-XNET FlexRay interfaces. It offers 82 dB/km attenuation with no termination. Additionally, the SHD9F-D9F FlexRay Cable has an impedance of 100 Ω, 148.94 Ω/km at 20 °C resistance, and 5.2 ns/m delay. The cable also features four 26 AWG twisted pairs and dedicated pairs for FlexRay Bus A and Bus B.
