Physical Layer
Tests hardware, electrical and procedural interface to the transmission medium.
-
Product
LTE/LTE-Advanced Analysis Using NI PXI RF Test Instruments
NI-RFmx LTE/LTE-Advanced
Test Instrument
Highly optimized RF measurement experiencePerform physical layer analysis on LTE cellular signals including MODACC, ACPR, CHP, OBW, and SEMIncludes support for TDD, FDD, and LTE-Advanced signals specified in 3GPP standards release 12Simple access to advanced measurement parallelism
-
Product
Industrial Ethernet Physical Layer Devices
-
The ADI Chronous™ Industrial Ethernet physical layer (PHYs) portfolio includes solutions for standard 10 Mbps, 100 Mbps, and 1 Gbps. It also features the new 10BASE-T1L technology for single-pair Ethernet.Our industry-leading low latency and low power PHY technology maximizes data transmission and signal integrity in deterministic applications by reducing cycle times and system power consumption. It enables superior synchronization of signals across the industrial network and supports the development of TSN.
-
Product
W-CDMA/HSPA+ Analysis Using NI PXI RF Test Instruments
RFmx W-CDMA/HSPA+
test
The NI-RFmx W-CDMA personality is a highly optimized API for performing physical layer measurements on W-CDMA cellular standard signals. NI-RFmx W-CDMA is completely interoperable with all NI-RFmx APIs. It provides simple access to the most advanced optimization techniques such as multi-measurement parallelism and multi-DUT measurements. The result is extremely fast and high-quality measurements with minimal software development efforts.
-
Product
Inmarsat-C Physical Layer Tester
CPLT
-
Square Peg Communications Inc.
Square Peg Communications Inc.’s Inmarsat-C Physical Layer Tester (CPLT) is a software application that runs on the generic high-rate Physical Layer Tester (PLTH) platform. The CPLT supports testing of the physical layer performance and protocol implementations of Inmarsat-C Mobile Earth Stations (MESs) and Land Earth Stations (LESs).
-
Product
Chassis
RSM/128-MF
Chassis
These Chassis controls up to 16 8x1 modules, 32 4x1 modules or any combination or configuration such as a 16x8 matrix, 32x4 matrix or two 16x4 matrices. Matrix configurations are non-blocking and physical layer switches act like a cable connection with D connectors creating a one to one connection between D9, D15 or D25 connectors.
-
Product
Xilinx Zynq ARM + FPGA SoM
TE0720
-
Sundance Multiprocessor Technology Ltd.
TE0720s are industrial-grade SoC modules integrating a Xilinx Zynq Z020 SoC, a gigabit Ethernet transceiver (physical layer), 8 Gbit (1 Gbyte) DDR3 SDRAM with 32-bit width, 32 Mbyte Flash memory for configuration and operation, and powerful switch-mode power supplies for all on-board voltages. A large number of configurable I/Os is provided via rugged high-speed stacking strips. All modules in 5 x 4 cm form factor are fully mechanically and largely electrically compatible among them. All this on a tiny footprint, smaller than a credit card, at the most competitive price. A free and open embedded development suite with reference designs is included.
-
Product
PXI DeviceNet Interface Module
Interface
PXI DeviceNet Interface Modules have an onboard microprocessor and optically isolated physical layer to communicate with a DeviceNet network system as a master (scanner) or slave device. The modules ship with a high-level API that provides complete access to a DeviceNet network and features easy access to device data and streamlined explicit messaging. PXI DeviceNet Interface Modules are ideal for prototyping DeviceNet systems, PC-based control, embedded control systems, PC-based human machine interface (HMI), and DeviceNet network management utilities.
-
Product
Isolated Controller Area Network (CAN)
-
ADI isolated controller area network (CAN) transceivers provide the differential physical layer interface between the data layer link, hardware protocol (for example, embedded in some of ADI's Blackfin® processors), and the physical wiring of the CAN bus. ADI's portfolio includes transceivers with integrated iCoupler® and isoPower® isolation, providing, fully isolated off-the-shelf CAN PHY's.
-
Product
SD Host Tester / SD / EMMC Analyzer / SD Card Tester
SGDK320A (SD Host Tester)
-
SGDK320A (SD Host Tester) is a product that has the functions of SD emulator (SD Emulator), host tester (Host Tester), SD analyzer (SD Analyzer), and eMMC analyzer (eMMC Analyzer). Supports SD Memory Card Physical Layer Specification Version 3.01. It covers the test contents of Test Specification Ver3.00 and Supplement Note. Supports SDR104 and eMMC ver4.41 (analyzer).
-
Product
PCIe 5.0 Protocol Analyzer
P5552A
Protocol Analyzer
The Keysight P5552A PCIe 5.0 Protocol Analyzer introduces a new form factor that is easily deployable in the lab bench environment to enable deep protocol analysis of a PCIe system with unparallel signal integrity. Locate protocol errors or validate device operations by viewing data from the physical layer all through the transactional layer with ease.
-
Product
64 Gbaud High-performance BERT
M8040A
Bit Error Rate Tester (BERT)
The Keysight M8040A is a highly integrated BERT for physical layer characterization and compliance testing. With support for PAM-4 and NRZ signals and data rates up to 64 Gbaud (corresponds to 128 Gbit/s) it covers all flavors of 200 and 400 GbE standards.
-
Product
Ethernet PHY
-
Macom Technology Solutions Holdings Inc.
MACOM’s portfolio of 10G/25G/40G/50G/100G Ethernet Physical Layer (PHY) devices offer unparalleled performance while maintaining high density at low cost. Integrated high-speed, high performance mixed signal I/O using advanced CMOS process nodes support a variety of optical and copper connectivity interfaces allowing the Ethernet PHY product line to span rack and cluster connectivity within the data center, wireless fronthaul, midhual and backhaul connectivity for 5G wireless infrastructure, and seamlessly extend to core networks over DWDM optical links. Advanced features such as in-service eye monitors, traffic monitoring, optical module identification and link training are just a few of the advantages that MACOM’s portfolio provides for end users to leverage for faster bring up, higher reliability and smarter networks.
-
Product
Network Connectivity Testers
-
The PingerPro Series provides a powerful combination of physical layer tools to troubleshoot copper/fiber links and LAN tools to identify and repair a wide range of network problems.
-
Product
PXI-8532, 1-Port, PXI DeviceNet Interface Module
781063-01
Interface
1-Port, PXI DeviceNet Interface Module—The PXI‑8532 is a high-speed DeviceNet interface for developing applications with the NI‑Industrial Communications for DeviceNet driver. DeviceNet is based on the CAN physical layer and increases strength and interconnectivity by specifying various parameters, such as the required cable length, connectors, and baud rates. DeviceNet specifications are managed by OVDA, Inc. You can program the PXI‑8532 to add high-performance master/scanner or slave capabilities to DeviceNet networks.
-
Product
Development Switch
AFDXSwitch Lab
-
The AFDXSwitch Lab operates in accordance to all requirements specified in the ARINC 664 part 7 standard. Features include traffic policing and frame filtering functions as well as integrity and error checking of frames. Additionally the switch comes with advanced features like 1 Gbit/s speeds, flexible physical layer configuration and extended environmental ratings. The AFDXSwitch Lab provides the full range of all technical functionalities of TTTech’s certifiable AFDX production switches, making it the optimal switching solution for a large variety of different application areas.
-
Product
CPE Design Verification System
Jupiter 310
Test System
Jupiter is the industry standard for automated DOCSIS physical (PHY) layer testing. It provides the most comprehensive test coverage and accurate results on the market for DOCSIS 3.1 devices.
-
Product
Industrial Ethernet Platform Solutions
-
ADI’s Industrial Ethernet platform solutions are complete network interface solutions designed to provide device connectivity for a large range of industrial, instrumentation, and other equipment. These solutions include both a physical layer and data link layer that manage the industrial protocol and network traffic for a host processor. ADI Chronous™ network interface solutions are complete communications subsystems that enable quick and simple inclusion of Industrial Ethernet connectivity to any end system.
-
Product
1 Channel, MIL-STD-1553, Dual Redundant, Direct Coupled, Assisted Mode Capable (AMC)
FTD
-
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
Product
CoolMaster
1000D
-
CoolMaster 1000D is versatile bridge device connecting Daikin VRV Air Conditioning systems and any RS232 or USB capable device like Home PC, Embedded PC or Home Automation Controller. Exposing simple interface over RS232 communication line or USB bus, CoolMaster gains user application full control on indoor units and provides access to VRV system parameters. In other words CoolMaster hides complexity of internal Daikin Communication line (including very unique physical layer) and instead gives simple, comprehensive, well documented protocol running on popular RS232 or USB connection.
-
Product
PXI/PXIe MIL-STD-1553 Multiplexer, Single 8-Channel, 2-Pole
42-739-003
Multiplexer Module
The 40-739-003 (PXI) and 42-739-003 (PXIe) are single 8-channel 2-pole multiplexers designed specifically for physical layer multiplexing or demultiplexing differential signals that conform to the MIL-STD-1553 specification. The module can be supplied as a single or dual 16-channel 2-pole multiplexer with each signal pair having a controlled 78 Ohm differential impedance.
-
Product
NI-9881, 1-Port C Series CANopen Interface Module
781673-02
Interface Module
The NI‑9881 is a high-speed CANopen interface for developing CANopen applications in LabVIEW software on CompactRIO hardware. CANopen is the application layer that sits on top of the CAN physical layer often used for industrial automation … applications. It was designed for motion-oriented machine control networks, such as handling systems, but now it is used in a variety of applications, including medical equipment, off-road vehicles, maritime electronics, public transportation, and building automation. The NI‑9881 can transmit/receive process data objects (PDOs) and service data objects (SDOs) according to CiA‑DS 301. The NI‑9881 is compatible with only CompactRIO systems.
-
Product
PXI/PXIe MIL-STD-1553 Multiplexer, Dual 4-Channel, 2-Pole
42-739-006
Multiplexer Module
The 40-739-006 (PXI) and 42-739-006 (PXIe) are dual 4-channel 2-pole multiplexers designed specifically for physical layer multiplexing or demultiplexing differential signals that conform to the MIL-STD-1553 specification. The module can be supplied as a single or dual 16-channel 2-pole multiplexer with each signal pair having a controlled 78 Ohm differential impedance.
-
Product
1 Channel, MIL-STD-1553, Dual Redundant, Transformer Coupled, Assisted Mode Capable (AMC)
FTA
-
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
Product
100BASE-T1 MEDIACONVERTER NXP
Art.-Nr.: TE-1600
-
The ideal physical layer conversion between Automotive Ethernet and your PC system. The 100BASE-T1 MediaConverter NXP establishes one direct point-to-point conversion between automotive ECU’s using 100BASE-T1 and any standard Fast Ethernet device with RJ-45 connector.
-
Product
Optical Limiting Amplifiers
-
Analog Devices high gain optical limiting amplifiers feature low power, low jitter, and excellent sensitivity performance. Our limiting amplifiers include receiver functions such as quantization, loss of signal detection, and SFF-8472-compliant average power measurement. Along with SFP, SFF, and GBIC MSA module designs, our amplifiers also support physical layer protocols that include 1 ×, 2 ×, and 4 × Fibre Channel, 10GBASE-LX4, multiple rate SONET/SDH up to OC-48 with FEC, and Gigabit Ethernet.
-
Product
Physical Layer Test System
N19301B
Test System
The N19301B Physical Layer Test System (PLTS) 2022 software is a powerful signal integrity tool for today’s high-speed digital designers.
-
Product
Efficient And Effective Physical Layer (PHY) Testing Of 10/100/1000Base-T Interfaces
-
Explore Sifos Technologies’ highly unique, plug’n play 10/100/1000Base-T Ethernet Physical Layer Testing Solutions. Cost Effective and Comprehensive PHY Testing without Scopes, Fixtures, Probes, and Test Signals.
-
Product
1000BASE-T1 MEDIACONVERTER
Art.-Nr.: TE-1401-1
-
The ideal physical layer conversion between Automotive Gigabit Ethernet and your PC system The 1000BASE-T1 MediaConverter establishes one direct point-to-point conversion between automotive ECU’s using 1000BASE-T1 and any standard Gigabit Ethernet device with RJ-45 connector.
-
Product
NI-9881, 1-Port C Series CANopen Interface Module
781673-01
Interface Module
The NI‑9881 is a high-speed CANopen interface for developing CANopen applications in LabVIEW software on CompactRIO hardware. CANopen is the application layer that sits on top of the CAN physical layer often used for industrial automation … applications. It was designed for motion-oriented machine control networks, such as handling systems, but now it is used in a variety of applications, including medical equipment, off-road vehicles, maritime electronics, public transportation, and building automation. The NI‑9881 can transmit/receive process data objects (PDOs) and service data objects (SDOs) according to CiA‑DS 301. The NI‑9881 is compatible with only CompactRIO systems.
-
Product
Physical & Protocol Layer Testing Solutions
-
Testing ensures expected functionality, increases stability, improves reliability, and provides a higher quality product to you customers
