Physical Layer
Tests hardware, electrical and procedural interface to the transmission medium.
-
Product
Fibre-Coaxial DOCSIS Analyzer
CABLERANGER
-
DOCSIS 3.0 analyzers for hybrid Fibre-Coaxial networks CABLE RANGER from PROMAX provide all the required measurements to install and carry the network maintenance of those hybrid networks using fiber optics and coaxial cables at the physical layer. The operating frequency range spans from 5 Mhz to 1700 Mhz, thus fulfilling DOCSIS 3.0 and 3.1 requirements.
-
Product
PCMCIA/PCCARD & PCI ExpressCard 54mm Cards
PCCD-A429 and ECD54-A429
Interface Card
Alta Data Technologies’ PCCD-A429 & ECD54-A429 interface modules offer a variety of ARINC-419/429/575/573/717 channel configurations with software selectable RX/Tx channels, baud rates, bit encoding and word configurations (Start/Sync/Stop length, Parity, bits/word, MSB/LSB). Encode or decode almost any ARINC-429 physical layer signal.
-
Product
PXI/PXIe MIL-STD-1553 Multiplexer, Dual 8-Channel, 2-Pole
40-739-004
Multiplexer Module
The 40-739-004 (PXI) and 42-739-004 (PXIe) are dual 8-channel 2-pole multiplexers designed specifically for physical layer multiplexing or demultiplexing differential signals that conform to the MIL-STD-1553 specification. The module can be supplied as a single or dual 16-channel 2-pole multiplexer with each signal pair having a controlled 78 Ohm differential impedance.
-
Product
SpaceWire Physical Layer Tester
141
-
The SpaceWire Physical Layer Tester (SPLT) is a tool designed to test, validate and verify a SpaceWire system across all levels of the SpaceWire standard. Two SpaceWire ports employ a special LVDS interface which allows the transmitted signals to be deliberately and measurably manipulated to test the capability of a unit under test to receive signals of varying quality.
-
Product
Combination Module: 2 Ch. MIL-STD-1553 & 12 Ch. Discrete I/O
CM8
-
The CM8 module is a combination of NAI's MIL-STD-1553B module, FTB, and Enhanced Discrete I/O module, DT4. The CM8 offers twelve channels of discrete I/O and two channels of MIL-STD-1553B communications. The twelve discrete I/O channels are programmable as either input (voltage or contact sensing with programmable, on-module pull-up/pull down current sources), or output (current source, sink, or push-pull) up to 500 mA per channel from an applied, external 3-60 VCC source. The discrete I/O channels also provide additional functionality modes such as Pulse Width Modulation (PWM) output mode and Pattern Generator output mode. The two MIL-STD-1553B communications channels feature a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
Product
C Series CANopen Interface Module
CAN Interface
The C Series CANopen Interface Module is a high-speed interface for developing CANopen applications. CANopen is a higher-level communication protocol based on the controller area network (CAN) physical layer. It was designed for motion-oriented machine control networks, but now it is used in a variety of products and applications, including medical equipment, maritime electronics, building automation, and more. The C Series CANopen Interface Module can transmit and receive process data objects (PDOs) and service data objects (SDOs) according to CiA-DS 301. Using the NI-Industrial Communications for CANopen driver, you can batch edit SDOs, configure slave nodes with LSS services support, as well as perform network management (NMT), heartbeat, node guarding, and CANopen synchronization functions.
-
Product
Ethernet Controller ICs
CP220x
-
The CP220x family is the industry's smallest single-chip Ethernet controller containing an integrated Media Access Controller (MAC) and Physical Layer (PHY).
-
Product
AXIe M8000 Series of BER Testers
Bit Error Rate Tester (BERT)
Simplified time-efficient testing is essential when you are developing next-generation computer, consumer, or communication devices. The Keysight M8000 Series is the highly integrated BER test solution for physical layer characterization, validation, and compliance testing. With support for a wide range of data rates and standards, the M8000 Series provides accurate, reliable results that accelerate your insight into the performance margins of high-speed digital devices.
-
Product
sbRIO-9881, Non-Enclosed, 1-Port C Series CANopen Interface Module
785966-01
Interface Module
The sbRIO‑9881 is a high-speed CANopen interface for developing CANopen applications in LabVIEW software on CompactRIO hardware. CANopen is the application layer that sits on top of the CAN physical layer often used for industrial automation applications. The sbRIO‑9881 can transmit/receive process data objects (PDOs) and service data objects (SDOs) according to CiA‑DS 301. The sbRIO‑9881 is compatible with only CompactRIO systems. Non-enclosed modules are designed for OEM applications.
-
Product
Layer Thickness Meter
CHY 113
-
It is usded to measure the thickness of metallic coatings (eg paint) only on substrates with ferromagnetic alloys (eg steel). The meter is designed to provide easy operation in one hand.
-
-
Product
Physical Contact Connectors
-
Amphenol Fiber Systems International
Physical Contact (PC) connections are characterized by the physical mating of two optical fibers. Precision ceramic ferrules are typically utilized for PC connections. A PC connection is accomplished by terminating the optical fiber into a precision ceramic ferrule. Epoxy is used to affix the fiber into the ferrule. The tip of the ceramic ferrule is polished in a precise manner to ensure that light enters and exits at a known trajectory with little scattering or optical loss. Polishing the terminated ceramic ferrule is a critical process in Physical Contact fiber optic connectors.
-
Product
Layer Thickness Gauges
-
PeakTech Prüf- und Messtechnik GmbH
Coating thickness gauges are used for the non-destructive measurement of coatings such as paint or plastic on metallic surfaces.
-
-
Product
Separation Layer Device
NivuScope 2
-
NivuScope 2 measurement system for reliable separation layer detection and sludge level measurement mainly in primary and secondary clarifiers
-
Product
Layer Release Systems
-
EVG's IR LayerRelease Technology is a fully front-end-compatible layer release technology that features an infrared (IR) laser that can pass through silicon, which is transparent to the IR laser wavelength. Coupled with the use of specially formulated inorganic layers, this technology enables an IR laser-initiated release of any ultra-thin film or layer from silicon carriers with nanometer precision.
-
Product
Health Physics Systems
-
Detection and quantification of radioactive material within the body is a key factor in determining internal personnel contamination and dose assessment. These measurements can be made on body fluid samples using lab instrumentation or through direct measurement of personnel. The measurement of body fluids is generally less attractive due to the bio-hazards and lack of immediate results unless non-gamma emitting nuclide measurements are required. The direct measurement of personnel for gamma emitting radioactive material provides rapid results, can determine where the material may be located within the body, and does not require mobility of the material through body fluids for detection.
-
Product
Physics Laboratory Instruments
-
We are the leading manufacturer and exporter of physics equipment. Our physics equipment are up to the international standard. Our team brilliant engineers put their best efforts to make best quality of physics instruments and have great expertise in making following physics laboratory instruments:-
-
Product
Automated Adhesive Layer Control System
-
The system is designed for visual control of the application of adhesive layers on corrugated board products before assembling them.
-
Product
Atomic Layer Deposition Systems
-
Atomic Layer Deposition (ALD) is a powerful way to build ultra-thin, super-precise coatings, one atomic layer at a time. It’s especially useful and efficient when working with tiny, complex 3D structures, making it a go-to technique in advanced semiconductor manufacturing.
-
Product
Material Testing & Physical Testing
-
Meeting the specifications put out by testing equipment manufacturers is critical when conducting quality control testing. We carry a wide variety of materials testing and physical testing products that are ideal for quality control testing along with research applications, letting you evaluate and test materials such as plastics, coatings, and chemicals. Physical properties testing products range from force and torque instruments, to hardness and thickness gauges, to viscometers and spectrometers.
-
Product
Road Layer Thickness Measurement
-
ElektroPhysik Dr. Steingroever GmbH & Co. KG
Non-destructive and easy – with our measuring devices for asphalt layer thickness. The road layer thickness measurement of asphalt and all non-metallic materials used in the construction industry is completely non-destructive thanks to the eddy current method.
-
Product
Physical Vapor Deposition Systems
-
Physical Vapor Deposition (PVD) systems use physical processes, like sputtering and evaporation, to deposit thin films with exceptional purity and control. These techniques are widely used in semiconductor manufacturing, optical coatings and protective applications.
-
Product
AFM-Raman for Physical and Chemical Imaging
XploRA Nano
-
Fully integrated system based on SmartSPM state of the art scanning probe microscope and XploRA Raman micro-spectrometer.Compact, fully automated and easy-to-use, the XploRA Nano concentrates the power of AFM-Raman into an affordable yet full-featured package, making TERS imaging a reality for all. The TERS proven system.
-
Product
Layer 3 Managed Ethernet Switch
EKI-9512E-4GRX
Ethernet Switch Module
M12 connectors with IP67 rugged housing, Complies with EN50155 & EN50121-3-2, Wide nominal power input range: 24~110VDC. Operating power input range: 16.8~137.5VDC, Supports X-Ring Pro for rapid and predictable convergence.
-
Product
Physical Property Measurement System
PPMS
-
The Quantum Design PPMS represents a unique concept in laboratory equipment: an open architecture, variable temperature-field system, designed to perform a variety of automated measurements. Available measurement options include all required hardware and electronics to immediately begin collecting publication-quality data, while the system is also easily adapted to custom user experiments. Sample environment controls include fields up to ±16 T and a temperature range of 1.9 - 400 K. The expandable design enables combining many features in one instrument to make the PPMS the most versatile system of its kind.
-
Product
Building Physics
-
* For determining the heat flow density up to max. 150°C.* Application-oriented designs, consisting of a meander ofopposing thermocouples that are embedded in a substrate.* In case of thick substrates no lateral circulation of the heat flowbecause of sufficient meander shell zone.* Software for k value measurement, see chapter Software
-
Product
10-Port Layer 2 Managed/Unmanaged Ethernet Switches
TEN710MW
-
*EN 50155 layer 2 managed Ethernet switch*Power boost for PoE+, max. budget 150W*Wide operating temperature range from -40°C to 75°C*Supports ERPS/QoS/LACP and more network control, and security features*Reliable IP54 & 5 years warranty
-
Product
Physical Testing
-
Testing is confidential and can be conducted according to the client's specifications, or such Standards as MIL-202, 331, 750, 810 and 883, as well as GSA, ASTM, ISTA, BIFMA, ANSI, industry and government.
-
Product
Non-contact Inline Sheet Resistance Measurement Module For Conductive Layer On Substrate
NC-700
-
*Inline measurement module for moving substrates such as PET film, glass or paper*Continuous measurement(~24h) in Roll to Roll with OFF-SET FREE capability system*Various applications from the research and development to the production line
