Ethernet Switching
-
product
5-Position Switch
27801
The 5-Position Switch is a normally open contact switch. It has a nice snappy feel, and returns to the center/un-pressed position immediately when it is released. By monitoring the input state of five pins, it’s easy for any Parallax microcontroller to detect whether the switch is in the up, down, left, right, or pressed position. It is possible for more than one position to make contact at a time, such as pressed+right, left+down, or pressed+right+down, for a total of 18 output states.
-
product
Single Bus 64-Channel 2A PCI Fault Insertion Switch
50-190-101
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
product
PXIe-2512, 7-Channel, 10 A PXI Signal Insertion Switch Module
780587-12
PXIe, 7-Channel, 10 A PXI Signal Insertion Switch Module—The PXIe‑2512 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXIe‑2512 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls (FADECs).
-
product
LXI Matrix Switching Unit
ProDAQ 6140
The ProDAQ 6140 provides a relay matrix which can be fitted between the sensors and actuators on a device under test and the data acquisition and control system. It allows to separately connect/disconnect the signals from either side and to connect them to an internal bus. In this way signals can be routed via the bus to new destinations or the bus can be used to monitor or supply test signals. This allows calibrating and debugging the system without disconnecting and separating channels throughout the system wiring.
-
product
Syscal Pro switch
The Syscal Pro is an all-in-one multinode resistivity and induce polarization imaging system for environmental and engineering geophysical studies. The Syscal Pro gathers a 10 channels receiver and a 250W, 2000Vpp internal transmitter which make it the more powerful system of the Syscal range. This system allows to perform up to 10 measurements at a time and its switching board allow to work for 48 (Switch-48) up to 120 (Switch-120) electrodes.
-
product
PXI/PXIe MEMS Optical Switch, Dual Insert/Bypass
40-860A-522-M
The 40/42-860A-522-M is a PXI/PXIe dual insert/bypass switch with ST connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
product
PXI/PXIe MEMS Optical Switch, Single Insert/Bypass, Single-Mode
40-860A-112-HI
The 40/42-860A-112-HI is a PXI/PXIe single insert/bypass switch with FC/PC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
product
3U CompactPCI Serial 6-slot SSL w/ RTM w/ Ethernet
1CPCIS-306-L210
3U CompactPCI Serial Backplane with 6 CompactPCI S.0 slots, system slot left, with rear IO : 1x CompactPCI S.0 CPU slot, 5x CompactPCI S.0 peripheral slots, with connectors for Rear Transition Modules (RTMs) in slots 2 to 6, Ethernet full mesh.
-
product
RF Routing Switches
Quintech Electronics and Communications Inc.
RF Monitoring and Routing Switch.
-
product
Configurable High-Density Switch Matrix PXI Card
GX6384
The GX6384 3U PXI multiplexer switch card provides users with the ability to switch and interface tester resources to multiple UUT connections. The card is available in three different configurations, supporting 32 x 2, 32 x 4, and 32 x6 switch configurations.
-
product
Low PIM Coaxial Switch, DC to 4 GHz, SP4T
87104P
Low passive intermodulation (PIM) is crucial for applications where two or more transmitted signals share a common antenna or whenever the transmitter signal is too high or the receiver is sensitive to high intermodulation. The Keysight 87104P is a low PIM SP4T coaxial switch, operating from DC to 4 GHz, which can help to keep the system PIM level low. A guaranteed 0.03 dB insertion loss repeatability and 3 million cycles of operating life ensures signal integrity, improves testing efficiency, and ultimately maximizes test throughput.
-
product
RF Capacitance Level Switches
ABB's RF Capacitance level switches feature one-step external calibration, immunity to material build-up, and a wide selection of probes for even the most challenging applications from low dielectric bulk solids to sticky slurries.
-
product
AC Filament Switching and Line Relays
*Heavy duty Elkonite contact tips*AC and DC versions available*AC versions available with or without internal rectifier PCB*Automated vision system and operator inspection*Comprehensive automated end of line testing*Test Certificates supplied with each relay*Certificate of Conformity supplied with each order*Recertification and repair services available
-
product
Dynatrol® Level Switch for Light Bulk Solids
CL-10GJ
Dynatrol® CL-10GJ Level Detector operates with consistent results on problem applications that have a tendency to bridge or pack. It handles difficult products such as flour, cocoa, sugar, pharmaceutical powders, powdered lime and additional bulk solid materials for high-, intermediate- or low-point level detection. The CL-10GJ is typically used with bulk solids in the density range of 10-15 lbs/ft3.
-
product
PXI Switching Modules
PXI switching modules provide high-efficiency signal switching based on a standard PXI platform. Keysight offers a wide range of modules with a variety of characteristics: high-speed multiplexer modules with switch times up to 500 μs, general-purpose switching modules up to 300 W, and high-density matrix switcher modules that provide up to 256 two-wire intercept points.
-
product
System for the Analysis and Jamming of 10/25/40/50/100Gbps Ethernet and Gen 6 (32GFC) Fibre Channel
SierraNet M328
The SierraNet M328™ system provides for analysis and jamming of 10/25/40/50/100Gbps Ethernet and Gen 6 (32GFC) Fibre Channel data capture and protocol verification for developers & protocol test engineers in LAN, SAN, NAS and other Ethernet and Fibre Channel applications. Available with eight SFP28 FlexPorts™ for maximum configuration and utility, the SierraNet M328 includes an easy to use, customizable software interface, large capture buffers, and the most advanced capture, triggering, impairment and filtering capabilities in the industry.
-
product
4x4 HDMI Matrix Switch with RS232 and IP Control
HSM-I-04-04
4x4 HDMI matrix switch with RS232 and IP control. Supports HDCP, deep color, multi-channel digital audio (up to 7.1 channels), and may be used with any combination of DVI (PC) or HDMI (HDTV) sources and displays.
-
product
4x2 HDMI Matrix Switch with RS232 Control
HSM-04-02
4x2 HDMI matrix switch with RS232 control. Supports HDCP, deep color, multi-channel digital audio (up to 7.1 channels), and may be used with any combination of DVI (PC) or HDMI (HDTV) sources and displays.
-
product
PXIe-2739 , 256-Crosspoint, 16x16, 2-Wire PXI Matrix Switch Module
782835-39
256-Crosspoint, 2-Wire PXI Matrix Switch Module—The PXIe‑2739 is a high‐density 16x16 PXI matrix switch module designed for routing signals within automated test systems and using electromechanical relays to perform immediate switch operations. It also offers features to monitor the health of deployed systems and plan for predictive maintenance, including onboard relay count tracking, a temperature sensor, and functional and resistive relay self-tests available through the NI Switch Health Center.
-
product
Data Matrix Switches
Data Matrix Switches from novotronik are used whenever it is necessary to route balanced or unbalanced data signals, analogue or digital. Blocking and non-blocking solutions for signal types like RS-422, ECL, LVDS, TTL and others are available. In addition to our standardized devices, we also know to convince in the realization of your individual requirements.
-
product
Ethernet/AFDX/BroadR-Reach PCI Fault Insertion Switch - 8 Channel
50-201-008
This high bandwidth differential PCI fault insertion card is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This card supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, BroadR-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground.
-
product
Quad-Port 25G PCIe Ethernet NIC
P425G
The P425G 4x25G PCIe NIC builds upon the success of the widely-deployed NetXtreme E-Series architecture by combining a high-bandwidth Ethernet controller with a unique set of highly-optimized hardware acceleration engines to enhance network performance and improve server efficiency.
-
product
LXI Optical Switching - 8x8 Matrix Plugin Module
65-280-313
The 65-280-313 8x8 matrix is part of the 65-280 and 65-281 ranges of optical plug-in modules offering matrix & insert/bypass or multiplexer & SPST topologies respectively with all models based on MEMS fiber optic switches and available in various populations per plugin. In addition, a choice of different connector styles to suit most applications is offered: FC/APC (for optimal performance), FC/PC, SC/PC and ST for general applications and LC for high density applications. They use MEMS (Micro-Electro-Mechanical-Systems) based optical switches to route signals between terminals by redirecting the optical signal. This is achieved using micromechanical mirrors driven by a highly precise mechanism activated via an electrical control signal.
-
product
GPIB (IEEE-488) Switching
Pickering's GPIB (IEEE-488) switching systems offer you a comprehensive line of switching modules that are ideal for functional test, factory automation and data acquisition applications. These GPIB switching systems range from small low-cost entry level systems to large high performance units with extensive built in self-test.
-
product
2 X 1 SCSI Switch For Rack Mount Or Tabletop
MODEL SS1
The SS1 SCSI Bus Switch allows two hosts to share peripherals or one host to access either of two sets of peripherals. Each port may be SE, HVD or LVD. Switching from one port to the other may be accomplished: a. locally with the front panel switch, b. remotely with a momentary dry contact closure, or c. remotely via the RS-232 port. A software template for the RS-232 port is included in the User Manual. In all cases switching does not occur until "bus free."
-
product
Single Or Dual Stream MIL-STD-1553A/BTest And Simulation Module For Standard Ethernet
ANET1553-x
The ANET1553-x is a member of AIM’s new line of Ethernet based modules for analysing, simulating, monitoring and testing MIL-STD-1553A/B databuses. For wireless applications, an ANET compatible USB Wifi dongle is optionally available. The capability to execute Python scripts in the ANET is a standard feature. For applications with multiple ANET devices AIM offers the ADock ANET Docking Station to host up to 4 ANET modules.
-
product
Net Series 1 Gigabit Ethernet
The standard NET Series design uses rugged stainless steel connector bodies with a naval bronze engaging nut. The use of metal key and Acme threads on the mating interface allows for easy mating and un-mating of the connectors, no matter where they are located. In addition to the contact spacing, which is optimized for this application, one of the keys to achieving the 1 Gbit/s transmission rates is in the unique terminations for both the cable and bulkhead connectors. These cable terminations can be performed at a number of the Teledyne Oil & Gas worldwide manufacturing and support locations.
-
product
GPIB-ENET/1000, Ethernet GPIB Instrument Control Device - North America 240VAC
781630-05
The GPIB‑ENET/1000 is an IEEE 488 controller device for computers with an Ethernet port. You can use this device to share a single GPIB system among many networked users or to control several test systems from a single networked host. The GPIB‑ENET/1000 features a password-protected web interface for easy configuration. It can also control IEEE 488 devices from anywhere on an Ethernet‑based (LAN) TCP/IP network (Gigabit, 100BASE‑TX, 10BASE‑T). Each device interfaces to and shares up to 14 GPIB devices from several network hosts, and you can control up to 100 GPIB‑ENET/1000 interfaces with a single computer. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
product
PXI Low-Density General Purpose Switch Modules
These PXI low-density general purpose switch modules provide cost-effective solutions for applications where a high number of relays is not required. All of these modules use a 96 pin male connector that is supported by our comprehensive range of cable and connector accessories, ensuring they can be quickly integrated into your test system with minimum effort.





























