Source Measurement Units
-
product
Portable Strain Gage Welding and Soldering Unit
700
A battery-operated capacitive discharge spot welder for attaching and wiring weldable strain gages and temperature sensors.
-
product
Robotic Vehicle Gap / Flush Measurement System
Automation
LaserGauge® Automation is a robotic system for measuring vehicle gap/flush on a moving assembly line. It is cost-effective, fast, flexible, and delivers LaserGauge® accurate measurements. Utilizing the Cross-Vector scanning and Blue Laser Technology, the system provides more assembled-panel surface information than any other robotic laser profiler.
-
product
21-Ch 6A-250VA 2-Bus Fault Insertion
YAV90077
21 channels 1 thread 6A 250V 2 Fault Insertion Buses Switching up to 250W CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
Light Measurement
Light is produced from many natural and artificial sources. Controlling light and having an accurate understanding of its output, directionality and the appearance of what it irradiates is key to product development, quality and the success of a light source. Here are just a few examples of why Labsphere is leading the industry in light measurement.
-
product
RR Signal Source
Behlman’s RR series of Railroad Signal Sources and Frequency Converters are low cost, highly reliable, switch mode units built for Railroad Signaling. The RR series can be supplied with any single or three-phase input and outputs a clean, regulated AC signal at a precise frequency from 25 Hz to 250 Hz. These rugged signal sources are built to support the rigors of operating in the harsh environment of Railroad signaling equipment.
-
product
High-Voltage & Control Measurement
PMK Mess- und Kommunikationstechnik GmbH
As a developer and manufacturer of high-voltage and control measurement technologyand high-voltage safety accessories, ROSS Engineering Corp is a long-standing partner of PMK.We are pleased to make this coveted technology accessible to you through our international sales network.
-
product
Laser Distance Meter for 60m With 10 Memories and Min. Measurement
MS-LDM360
*Measuring distance: 0.05 to 60m*Accuracy: ±1.5mm (±0.06in)*Unit conversion: mm/in/ft*Laser classification: Class 2*Laser type: 635nm <1mW*Dynamic measurement*Area, volume measurement*Pythagorean proposition measurement*Indirect measurement*Add - subtract calculation*Minimum measurement
-
product
16 Channel, Single Slot, Bench Data Acquisition Unit with 6.5 Digit DMM
T3DAQ1-16
÷10 HiZ 500 MHz Passive Probe for WaveSufer 400 Series Oscilloscopes. Includes Spring Tip, tip protector, and standard accessories package.
-
product
Source Signature Recorder
*GPS accuracy for time break collection and source equipment locations.*32-bit, high speed, ADC chip for lower noise and increased accuracy for signatures.*Operates independently of crew, including observer and shooter or operators.*Can be used with any Vibrator Control System.*Great for monitoring rental equipment and operators.*Provides accurate start times that can be used with any nodal recording system.
-
product
Long Life Seismic Energy Source
1900LLX-T
Output volume of 10 cubic inches to 250 cubic inches. Light weight enough for shallow draught vesselsPowerful enough for blue water seismic surveys. Available with engineered seals for more robust performance.
-
product
Releaseit Shallow Water Deck Unit
Teledyne Benthos’ new Releaseit Deck Unit and dunking transducer enables communications and acoustic release functionality when used with any of Teledyne Benthos’ R-Series Acoustic releases deployed in shallow water environments. Designed with Teledyne Benthos’ proven engineering and reliability, Releaseit is a value-priced alternative deck unit allowing for basic coastal operations. When paired with our new R500 Shallow Water Acoustic Release, the combined system represents a lower-cost turn-key option for shallow water applications up to 500 m water depth.
-
product
Measurement Front End of the ACQUAlab Generation
LabBGN
labBGN is the first of the new ACQUAlab generation of measurement front ends. It is used in conjunction with the background noise simulation systems 3PASS HAE-BGN/ HAE-car, the communication analysis system ACQUA and other HEAD acoustics components.
-
product
Signal Conditioners & Measuring Transducers
Signal conditioners and measuring transducers ensure interference-free signal transmission in measurement and control technology. From highly compact 6 mm signal conditioners and measuring transducers through signal conditioners with functional safety to signal isolators for intrinsically safe circuits in the Ex area: our signal conditioners and measuring transducers ensure interference-free signal transmission in MCR technology.
-
product
M² Measurement Systems
Thorlabs' M2 Measurement Systems provide self-contained, turn-key solutions for measuring M2, divergence, focus diameter, waist position, Rayleigh length and other laser beam quality metrics. Pre-configured, factory-aligned systems covering wavelength ranges between 250 nm and 2700 nm are available. Choose from among systems that have a scanning-slit beam profiler, a camera beam profiler, or no beam profiler.
-
product
Impulse Current Measuring Shunts
ICMS
The Impulse Current Measuring Shunts ICMS are new designed tubular shunt types with best response behavior to match the high performance of the TR-AS digital recorder for comparative current measurements. A 1st partial response time less than 10ns and a settling times less than 20ns show the advantage of these shunts. They show no initial overshoot peak, no oscillations and do not need compensation box to optimize the transient behavior as known from e.g. cage shunts.
-
product
Emergency Power Supply Units (EPSU) (10) 5-20R 1U/0U V/H
EPS-1020-HV
EPSU Power (Basic / Surge / Metered / Value) – rack mountable power distribution, 120V, optional surge suppression, and amp meter
-
product
Broadband Coaxial Noise Sources
Our integrated noise modules contain all the required biasing circuitry and only need a positive voltage to activate for an easy installation. Since they typically do not contain amplification, the raw noise output from the diode is seen at the output of the module resulting in a maximum ENR of approximately 35dB. Primary applications include system built-in test and laboratory use.
-
product
Differential And I/Q Device Measurements
S97089B
The S97089B combines source-phase control of multiple internal or external sources with frequency-offset mode, enabling simplified test of I/Q modulators/converters, differential mixers, and harmonics or amplifiers
-
product
Drawing Die And Wire Measurement
DGMS – Die Geometry Measuring System
Optik Elektronik Gerätetechnik GmbH
Measuring system for diameter, roundness, reduction angle and bearing length of wire drawing dies.
-
product
Temperature Measurement System
TMM-100
Thermal Engineering Associates, Inc.
The self contained TMM-100 module accepts diode, thermocouple and thermistor temperature sensors. The USB-connected instrument is supplied with Windows™ 7, 8 & 10 compatible software that provides for sensor measurement on a cyclic basis and for data logging of all measured values. LabVIEW™ Virtual Instrument (VI) drivers are available as an extra cost option for users that wish to incorporate the TMM-100 into an application-specific measurement environment.
-
product
Measuring Instruments for Gas Leak Detection
Here you will find an overview of measuring instruments from Sewerin for gas leak detection. Our portfolio includes gas warning devices, gas leak detectors, gas concentration measuring devices, multigas meters, combination measuring devices, ethane detectors, odorant measuring instruments, biogas measuring devices and a whole lot more...
-
product
Four Chanels Desktop CWDM/LanWDM DFB Laser Source
UC8134
The UC8134 Four Chanel Desktop CWDM/LanWDM DFB laser source offer superior performance for the test of CWDM, DWDM components, AWG & PLC components, optical amplifiers, and other general purpose of fiber optical test and measurement applications. It is special design for volume couplers, transceiver/receiver and PLC production line application.
-
product
AC-DC Rectifier Unit
Supreme Instrument Laboratories
Continuously variable/manually variable D.C. Rectifier unit to be used in the Electrical Engineering Laboratories, with the following technical specifications
-
product
Multi-Cluster Sources
Our complete line of sources can be configured in a Tri-Source configuration. Clustered sources are a vital part of effective seismic exploration. The destructive effects of the air blast associated with a discharging air source are made worse by clustering. In order to maintain the separation between air sources within a cluster, it is necessary to mechanically constrain the sources with rigid bars.
-
product
Pan/Tilt Unit for Side-Mounted Payloads up to 15 lbs
FLIR PTU-D48E
The PTU-D48 E-Series supports any type of single or multi-part payload through a flexible bracketing system of top and/or side mounting. The real-time command interface supports advanced applications such as video tracking. The PTU-D48 E-Series has been proven in a wide range of mission-critical applications for positioning of cameras, lasers, antennas, or other instruments in both fixed and mobile environments. It is designed for high duty cycles and reliable operation 24/7 in harsh all-weather environments.
-
product
SM / Expansion Unit
A testing procedure designed to thoroughly test the electrical characteristics of a wire or cable, may require additional test points to connect the end points of all conductive paths. The changing and alteration of Test Adapter Cables (TACs) would become obsolete when having access to one or several expansion units. Increased testing efficiency alleviates the long, drawn out down times of the disabled aircraft while improving product readiness. Additional time can be spent on troubleshooting and problem identification and will not require the user to unhook and connect TACs to different matrices. Adding additional expansion units will save the user time, money, and effort.
-
product
Unit Injector Expert
UInEx-2
UInEx-2 (Unit Injector Expert) is a device for comprehensive diagnostics of passenger car unit injectors. It enables detailed electrical and mechanical tests, such as:
-
product
Power Sensor and SNS Noise Source Cables (3 m/10 feet)
11730B
The Keysight 11730 series power sensor cables are used with the 8480 and E-series power sensors (except the E9320 family of peak and average sensors). These cables are designed to reduce RFI effects on low power readings with an improved shielding design in the cable itself. Cables may be ordered individually or in pairs in any combination desired for single and dual-channel measurements.
-
product
Low Phase Noise Reference Source
96270A
The 96270A RF Reference Source is the simplest, most accurate and cost-effective single instrument for calibrating spectrum analyzers and RF power sensors and more, up to 27 GHz.
-
product
CD Measurement and Advanced Film Analysis
FilmTek CD
Scientific Computing International
SCI’s leading-edge solution for fully-automated, high-throughput CD measurement and advanced film analysis for the 1x nm design node and beyond. Delivers real-time multi-layer stack characterization and CD measurement simultaneously, for both known and completely unknown structures. Patented multimodal measurement technology meets the challenging demands associated with the most complex semiconductor design features in development and production.
