usb power sensor
-
product
Precision Sensors for Aerospace
IC² delivers scientific-grade precision sensors that push the envelope of aerospace measurement accuracy and performance. Offering a suite of sensors and instrumentation for aerodynamic and aeroacoustic measurement applications, including direct-measurement shear stress sensors, aeroacoustic microphones and dynamic pressure sensors and arrays, our sensors are designed to meet rigorous performance specs and survive harsh environments, making them ideal for wind-tunnel and in-flight measurements.
-
product
Hall Sensor Board with I2C Interface
046-323
Version: +5V/60A +3,3V/15A +12V/15A -12V/15A The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
-
product
Turbo Controllers Tester (USB)
VNTT-PRO V4.07
The tester is designed to test the efficiency of electronic turbocharger controllers.
-
product
USB HD-SDI Video Processor/Capture Card with Overlay
2246
Video overlay up to full screen at up to 1920x1080 SDI (HD/SD) and analog inputs DVI, SDI (HD/SD), and analog outputs Prescaled SD A/V compression engine with MPEG-1/2/4 output Up/downscaling on DVI and analog outputs Captures uncompressed HD/SD frames Generates "freeze frame" video from captured frames Video "zoom" on MPEG stream and DVI output Isolated general-purpose digital I/O: 8 in / 4 out USB 2.0 interface
-
product
Modular Power
RFP DC Load
AMETEK Programmable Power, Inc.
ReFlex Power™ is a high density, modular programmable power system providing DC, AC and electronic load assets all under control of a single controller. It provides a reconfigurable, flexible platform ideal for ATE and production test environments where RFP™ can provide programmable stimulus and bias power as well as programmable loads for the device(s) under test. The EIA 4U high RFP™ mainframe can hold up to 12 single-slot modules or combinations of single, dual and triple slot wide modules to configure (or reconfigure) the system for the particular requirements at hand. The mainframe can support up to 6 kW of output power.
-
product
Bipolar Power Transistors
A wide variety of products are rolled out, for example, for uses at high temperature (up to 175°C applicable), high power, and low Vce (sat), and others.
-
product
Power Systems Recorder
TESLA 3000
ERLPhase Power Technologies Ltd
TESLA 4000 is an easy-to-use and cost effective, state-of-the-art, multi-time frame (simultaneous) power system monitoring recorder. Its integrated Phasor Measurement Unit (PMU) functionality streams synchrophasor data for wide area monitoring. Enabled with IEC 61850 protocol, TESLA has advanced communication capabilities that, together with its powerful recording features, provide the most versatile and complete monitoring of power system health.
-
product
Power Quality Analyzer
Beijing GFUVE Electronics Co.,Ltd.
Used to continuously monitor and analyze electricity lines for disturbance.
-
product
Series Dual Temp / Acceleration Sensors
TA104
Dual Temperature / Acceleration Output, Side Exit Connector / Cable, 100 mV/g, 10 mV/?C
-
product
Power Supply, 30V, 50A, 1500W
N5765A
Keysight basic DC power supplies offer essential features for a tight budget. The Keysight 1500W, single output N5765A provides universal AC input, GPIB, LAN, USB, LXI compliance, and analog/resistance control of output voltage and current. It delivers solid performance and a variety of basic and enhanced capabilities in a compact 1U package.
-
product
Precipitation Sensors
Campbell Scientific offers several types of sensors to measure precipitation: tipping bucket rain gages, siphoning tipping bucket rain gages, heated rain gages, and snowfall adapters. Users often select their precipitation sensors based on the type of precipitation to be measured (rain or snow), as well as the needed orifice diameter, measurement range, and accuracy level.
-
-
product
Power Quality Analyzers
Is used to measure electric power signals to determine the load's ability to function properly with that electric power.
-
product
Fiber Optic Temperature Sensor with the EasyDisk
The TPT-62
The TPT-62 fiber-optic temperature probe family employs industry standard 62.5µm core OM1 fiber optic for highly improved optical, mechanical, and reliability properties over legacy 200 µm core (1st generation) fiber optic sensors. The EasyDisk sensor tip assembly ensures IEC60076-2 (Annex E) compliant installation and enables quick insertion of the probes into the spacers within the windings of transformers.
-
product
Belt Alignment Sensors And Misalignment Switches
Electro-sensors belt alignment sensors are mounted along the conveyor belt that needs to be monitored for misalignment. The rub block assemblies are mounted so that the brass surface area is in-line with the edge of the conveyor belt. When the belt wanders it then rubs up against the brass block. The contact with the belt creates friction and heat that the sensor in the brass block records as a rise in temperature.
-
product
Vehicle Test Sensors
Today's engines contain sensors to tell the vehicle's computer what's going on. Car sensors check for fuel-air mixture, incoming air temperature, wheel speed, and manifold pressure. They then tell your vehicle's computer what to do, based on that information.
-
product
Power Supplies
CU-600B
The CU-series is a semi-modular power supply that lets you select the cables you need while powering your system at a healthy voltage. Everyone likes a clean and easy installation. This power supply allows you to keep what you want and remove what you don't. While necessary connectors, like the 20+4 pin power connector, are attached to the unit, you decide which of the others should stay. Customize your power supply to reflect your system.
-
product
Fluid Level Sensor
The output of the fluid level sensor is a voltage which changes in direct proportion to the level of fluid in the probe. The difference in permittivity between air and the fluid being measured changes the capacitance between the probe's two concentric tubes as the level changes. An RS232 connection to a PC allows the user to calibrate the fluid level and thermal drift compensation. The probe is factory replaceable, allowing the electronics to be re-used should the probe become damaged or if a new probe length is required.
-
product
Gas Flow Sensors
ESRF-HF Transmitter
The ESRF-HF is a family of mass flow transmitters which enable fast and accurate measurements of gas flow over a wide dynamic range. Each transmitter integrates a MEMS flow sensor and readout electronics inside a housing with very small form factor made from stainless steel. The duty pressure of the flow transmitter is 11bar. All measurement data are fully calibrated, and temperature compensated on board, leading to a reduced temperature coefficient and high measurement accuracy.
-
product
Line Post Sensors
These products are designed for distribution circuits only at their rated capacities. They cannot be field modified for capacities other than what was shipped with the units.
-
product
Sensors
Networked Communication Solutions, LLC
Networked Communications Solutions (NCS) provides a wide range of low-cost wireless sensors solutions designed for commercial and industrial and consumer applications. Wi-In™ detects and monitors every function critical to your network including light, humidity, temperature and distress. NCS system Wi-In™ allows for user customization and includes free online sensor monitoring with SMS text and email alerts. NCS Wi-In™ sensors are designed for easy installation and can be remotely monitored by anyone needing to check the functionality of their networked systems.
-
product
Temperature Sensor
The Temperature Sensor works with NI measurement devices and software to help you acquire temperature data within a measurement system. You can use LabVIEW or FlexLogger software and NI-DAQmx driver software to configure measurements and predefined scaling coefficients for Temperature Sensors and acquire synchronized temperature data.
-
product
Temperature Sensor
Aanderaa temperature sensors are compact, intelligent temperature sensors designed for use on Aanderaa Data Instruments Dataloggers and as stand-alone units.
-
product
Power Supplies
CX Series
The CX-series has 120mm fan. It has a high quality silver-coated fan guard and cable-tube on main power cables for better cable routing and neatness. This power supply is also compatible with all leading processors. Chassis come in a black & silver color to best suit your preferences.
-
product
High Amps, Contact, Receiver, 500+ Amps, 350 MCM
610152101
High Amps, Contact, Receiver, 500+ Amps, 350 MCMContact rated to 1500VDC for low duty test applications.Mating contact 610153102. (NOT compatible with other VPC contacts)Contact ONLY compatible with 310105172 Receiver.
-
product
Split Type AC Current Sensor
CTF-10
MULTI MEASURING INSTRUMENTS Co., Ltd.
*For AC current and power measurements.*Wide measuring range (AC 0.1～60A).*Compliant with RoHS drective.
-
product
Powered VXI Crates
6U VXI-C Size High Power Receiver Crate
The WIENER high power C-size VXI receiver mainframe is optimized for test applications with demanding power requirements. Up to 6kW DC power can be provided and distributed to the VXI modules.
-
product
Doppler Sensor Modules
Doppler radar measures the Doppler effect, or an increase or decrease in the frequency of sound, light, or other waves as the source and observer move toward or away from each other.
-
product
E-Series Average Power Sensor
E9300B
Measure the average power of all modulation formats Wide dynamic range power measurements from -30 dBm to +44 dBm Frequency range 10 MHz to 18 GHzLow SWR for reducing mismatch uncertainty Calibration factors, linearity and temperature compensation data stored in EEPROM Compatible with EPM (new N1913A/ 14A, E4418B/ 19B), EPM-P (E4416A/ 17A) and P-series (N1911A/ 12A) power meters
-
product
Power Temperature Cycling
Typically, this test would be selected when during its normal operating activity, the device is subjected to high temperature excursions and is required to power on and off at all temperatures. The power and temperature cycling test will determine the ability of a device to withstand exposure to such temperature extremes with operating biases periodically applied and removed. The worst case conditions expected in a typical; application will be simulated.
