DMM
Electronic measurement instruments that combine multiple functions in a single unit and output information through a digital display, in a numeric value.
-
-
Product
DMM Test Probe Kit With Multi-Stacking Banana Plug
5325A
-
DMM test probe kit with multi-stacking banana plug
-
Product
ABex Terminal Module for NI 407x and 408x DMM Cards
ABex TM-4070 DMM
-
The ABex TM-4070 is an ABex terminal module to interface with NI PXI-407x or PXIe-408x and gives the possibility to rout the DMM signals to the front connector and the Analog bus. The routing to the analog bus is software controlled and the signals are switched with reed relays.
-
Product
Precision DMM with RS232 Interface
HH2215
-
Resistance test up to 40MΩ. Wide Frequency test range from 10Hz to 300kHz. Capacitance measurement up to 100uF. Temperature test range from -4oF to 572oF to 300oC. Diode test audible continuity check and Transistor test
-
Product
PathWave BenchVue USB Modular DMM Pro
BV0021B
-
Connect and control your U2741A DMM to make measurements, plot graph and log unrestricted data with PathWave BenchVue USB digital multimeter software.
-
Product
2-Channel 40KSPS Datalogging Oscilloscope / 2-Channel 5.5 Digit DMM CF Card
CFD200
-
The CFD200 is a new concept in test equipment that allows a PDA, laptop or tablet PC to be turned into a dual channel Digital MultiMeter with sophisticated analysis capabilities. SmartAnalysis software facilitates step-by-step fault investigation with instant display of results and an interactive diagnostic guide. With the CFD200 it is possible to integrate multiple measurement functions into a single hardware/software platform, providing high-level analysis features and a small, lightweight and portable unit. The CFD200 is an extended Compact Flash design offering two channels with full galvanic isolation to host and channel-to-channel. Each offers a scope function up to 40KSPS with full datalogging capability and 650V max. input voltage.
-
-
-
Product
Manual-Hardware 218 24-bit DAQ (DMM) Elan/Ines PCMCIA DAQ Cards
Manual-DAQ218HW
-
*Hardware manual for current Elan/Ines 24-Bit Data Acquisiton Cards:*DAQ i218*TS-C-AD218
-
-
Product
6½ Digit DMM / Digitizer PXI Card
GX2065
-
The GX2065 offers a unique combination of features, resolution, accuracy and speed in a compact, single slot 3U PXI format. Featuring 6-½ digit resolution, 0.005% basic DCV reading accuracy and up to 3,500 reading per second (rps) assures you of measurements that are accurate, fast and repeatable. All measurement functions including digitizing functions are isolated from the PXI bus - providing the ability to make true differential, floating measurements. An on-board controller performs all necessary DMM and digitizer calculations, minimizing PXI control bus overhead.
-
Product
Bench-Type DMM with Output Terminals.
SK-4033/SK-4035
-
Suitable for Factory Automation.PhotoMOS relay output terminal.Comparator function.True RMS (SK-4035).10 times/second sampling rate.
-
Product
Cable Assembly, Receiver, TriPaddle, 20", (for NI PXI-2527) with Banana Plugs for a DMM
541122953
-
Cable Assembly, Receiver, TriPaddle, 20", for NI PXI-2527 with Banana Plugs for a DMM
-
Product
DMM MULTIMETER TEST LEADS
-
Flexible Vinyl Strain ReliefSoft Silicone Leads48" Length, 18 Gauge1000 Working Volts10 AMP RatedLow-resistance Gold ContactsRetractable Safety Shroud
-
Product
16 Channel, Single Slot, Bench Data Acquisition Unit with 6.5 Digit DMM
T3DAQ1-16
-
÷10 HiZ 500 MHz Passive Probe for WaveSufer 400 Series Oscilloscopes. Includes Spring Tip, tip protector, and standard accessories package.
-
Product
Insulation Tester, Analogue / Digital Megohmmeter, 50V, 100V, 250V, 500V, 1kV, 0.01ohm to 20Gohm
72-3105
-
Insulation Resistance Tester Full function DMM includes AC and DC voltage measurement, plus a wide range of resistance scales designed specifically for insulation resistance measurement. It is ideal for safety and preventative maintenance work on powered tools, motors, transformers and similar devices. Large backlit 6000 count display provides at-a-glance readings via both 3-3/4 digit readout and 45 segment analog bargraph.
-
Product
SWB-2811, 8x21, 1 A, Reed Relay Matrix Module for SwitchBlock
781420-11
-
8x21, 1 A, Reed Matrix Module for SwitchBlock - The SWB‑2811 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
PXI RTD Simulator Module 6-Channel PT1000
40-262-102
-
The 40-262 is a 3U PXI module range that supports 6 (in one slot), 12 or 18 (in two slots) channels of RTD simulation. Based on the 40-260 design principles the module can provide a setting resolution of <8mΩ (PT100) or <90mΩ (PT1000) and a resistance accuracy of better than 0.1% on all channels. Each simulation channel is able to provide a short or open circuit setting to simulate faulty wiring connections to a sensor. Calibration or verification of each resistor channel can be verified by using the calibration port connected to a high performance DMM and a supplied software package.
-
-
Product
High Current Calibrator
MC151
-
MC151 Current calibrator is an accurate current source capable of 120 A. Typical uses include calibration of current sensors, current probes, current transformers, shunts, ammeters, DMMs or as stable current source for test and development applications. The calibrator is equipped with a built-in multimeter that can be used for simulation of programmable transconductance or current amplifier.
-
Product
Handheld Digital Multimeter, 3 ½ Digit
U1232A
-
Ergonomic shaped 6K counts DMM with flashlight, low input Z mode and continuity visual/audio alerts. Keysight Remote Link Solution enabled.
-
Product
PXIe-4081, 7½-Digit, ±1,000 V, Onboard 1.8 MS/s Isolated Digitizer, PXI Digital Multimeter
783130-01
-
PXIe, 7½-Digit, ±1,000 V, Onboard 1.8 MS/s Isolated Digitizer, PXI Digital Multimeter—The PXIe‑4081 is the industry’s most accurate 7½‑digit DMM and provides the measurement capabilities found in two common test instruments: a high-resolution 1,000 V DMM and a digitizer. As a DMM, the PXIe‑4081 delivers fast, accurate AC/DC voltage, AC/DC current, 2‑ or 4‑wire resistance, and frequency/period measurements, as well as diode tests. In the high-voltage, isolated digitizer mode, the PXIe‑4081 can acquire waveforms at sample rates up to 1.8 MS/s.
-
Product
Multimeters
-
Whether you work in industrial, HVAC, commercial or residential electrical environments, there’s an Amprobe digital multimeter with features to match your requirements. From heavy-duty industrial Amprobe DMMs with CAT IV safety ratings, to pocket size meters that handle all the basics, Amprobe makes some of the best digital multimeters around. Whatever your application, there’s an Amprobe multimeter ready to get the job done.
-
Product
Optometers, Amplifiers, Display Meters
-
Optometers are a specific type of digital multimeter (DMM) used for optical radiation measurements. The particular light detector(s) connected determine the wavelength range/spectral weighting function and displayed measurement units.
-
Product
Keysight Dual 4x16 Armature Matrix for 34980A
34932A
-
The Keysight 34932A module for the 34980A Multifunction Switch/Measure Unit gives you the most flexible connection path between your device under test and your test equipment, allowing different instruments to be connected to multiple points on your device under test at the same time. Dual 4x16, 8x16, or 4x32 configurations 128 2-wire cross-points 300 V, 1 A switch; 2 A carry current Connections to the internal DMM Latching armature relays, with relay counter Expandable via four 2-wire analog buses
-
Product
Digital Multimeters
-
A digital multimeter (DMM) is a test tool used to measure two or more electrical valuesprincipally voltage (volts), current (amps) and resistance (ohms). It is a standard diagnostic tool for technicians in the electrical/electronic industries.
-
Product
Digital Multimeter with CE
-
ZHANGZHOU HUAYI ELECTRONICS CO.,LTD.
A digital multimeter (DMM) is a test tool used to measure two or more electrical valuesprincipally voltage (volts), current (amps) and resistance (ohms). It is a standard diagnostic tool for technicians in the electrical/electronic industries. CE indicates that the product was designed and manufactured to mandatory European Safety and EMC/EMI requirements.
-
Product
VXI Modular Digital Multimeters
-
Whether youre in product development, design validation, or manufacturing, Keysights digital multimeters (DMM) come packed with the performance and flexibility you need.
-
Product
SWB-2812, 16x9, 1 A, Reed Matrix Module for SwitchBlock
781420-12
-
16x9, 1 A, Reed Matrix Module for SwitchBlock - The SWB‑2812 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
Electrical Dmm Test Lead Kit For Most Hand-Held Meters
5673B
-
Electrical DMM test lead kit for most hand-held meters
