Noise Bridges
examine antenna's capability to recieve and/or transmit wireless rf signals.
See Also: Bridges
-
Product
Noise Bridge, RF 1 MHz to 100 MHz
MFJ-202B
-
Quickly adjust almost any antenna for maximum performance, 1 to 100 MHz. Lengthen or shorten your antenna for minimum SWR. Measure resonant frequency, feedpoint resistance and reactance. Works with any receiver or transceiver. Hand-calibrated resistance scale, expanded capacitance range and exclusive built-in range extender.
-
Product
Ultra-Low Noise Filter, 42 V / 105 MA, 50 Ω
N1298B
Noise Filter
The N1298 Series is a collection of low noise filters for the Keysight B2960 Series 6.5-digit low noise source.
-
Product
RF Bridge, 50 Ohm, 300 kHz to 6 GHz
86205A
RF Bridge
The Keysight 86205A high directivity 50 ohm RF bridge offers unparalleled performance in a variety of general-purpose applications. It is ideal for accurate reflection measurements and signal leveling applications.
-
Product
Noise Source Test Set, 10 MHz to 26.5 GHz
N2002A
Noise Source
The N2002A noise source test set is a low cost, stand-alone instrument that, as part of a calibration system, enables fast, repeatable calibrations with minimal levels of uncertainty.
-
Product
Noise Source, 1 GHz up to 40 GHz
346CK40
Noise Source
The Keysight 346CK40 is the ideal companion to Keysight´s noise figure solutions when working on high frequency applications. Since it is broadband (1 GHz to 40 GHz), it eliminates the necessity for several sources at different frequency bands. The low SWR of the noise source greatly reduces measurement uncertainty, which are commonly reflections of the test signals. This is a coaxial noise source with a 2.4 mm coaxial connector. ENR typically 14 dB at 1 GHz, decreasing to 5 dB at 40 GHz (typical).
-
Product
SNS Series Noise Source 10 MHz to 18 GHz (ENR 6 dB)
N4000A
Noise Source
The SNS series N4000A noise source is designed for accurately measuring devices with low noise figure, with a frequency range of 10 MHz to 18 GHz and nominal ENR 6 dB.
-
Product
Noise Source, 10 MHz to 18 GHz, nominal ENR 6 dB
346A
Noise Source
The Keysight 346A noise source is the ideal companion to Keysight's noise figure solutions. Since it is broadband (10 MHz to 18 GHz), it eliminates the necessity for several sources at different frequency bands. The low SWR of the noise source reduces a major source of measurement uncertainty; reflections of test signals. The very small change in reflection coefficient (<0.01) from ON to OFF is designed especially for accurate characterization of input-impedance-sensitive devices (like GaAsFETs and many UHF amplifiers).
-
Product
Noise Figure Analyzer, Multi-touch, 10 MHz to 7 GHz
N8974B
Low-Frequency Noise Analyzer
The N8974B high performance noise figure analyzer is designed to make fast, accurate and repeatable noise figure measurements. When paired with an SNS Series noise source and U7227 Series USB preamplifier the ENR data from the SNS and USB preamplifier data automatically downloads into the N8974B.
-
Product
Phase Noise Test System
N5511A
Phase Noise Analyzer
The Keysight N5511A phase noise test system (PNTS) lets you measure at the limits of physics with readings down to kT (-177 dBm/Hz). The N5511A PNTS is a replacement for the gold-standard Keysight E5500 phase noise measurement system and is designed to meet the needs of phase noise power users.
-
Product
Phase Noise Analyzer and VCO Tester
FSWP
Phase Noise Analyzer
The R&S®FSWP phase noise analyzer and VCO tester features very high sensitivity thanks to extremely low-noise internal sources and cross-correlation. It can measure phase noise and amplitude noise in mere seconds on highly stable sources such as those in radar applications. Additional options such as pulsed signal measurements, residual phase noise (including pulsed) characterization and integrated high‑end signal and spectrum analysis make the R&S®FSWP a unique test instrument.
-
Product
Noise Source, 10 MHz to 18 GHz, nominal ENR 15 dB
346B
Noise Source
The Keysight 346B noise source is the ideal companion to Keysight's noise figure solutions. Since it is broadband (10 MHz to 18 GHz), it eliminates the necessity for several sources at different frequency bands. The low SWR of the noise source reduces a major source of measurement uncertainty; reflections of test signals. The 346B's high ENR, low SWR, and variety of connectors make it a general-purpose noise source. Add special option H01 for high ENR (21 dB typical) to measure high noise figure devices, or option H42 for measuring Direct Broadcast Satellite (DBS) low noise block converters.
-
Product
SNS Series Noise Source 10 MHz to 18 GHz (ENR 15 dB)
N4001A
Noise Source
The SNS series N4001A noise source is ideal for general purpose use with a low reflection coefficent and a nominal ENR of 15 dB from 10 MHz to 18 GHz.
-
Product
Advanced Low-Frequency Noise Analyzer
E4727B
Low-Frequency Noise Analyzer
Get a deeper, closer look at low frequency noise with the A-LFNA integrated with WaferPro Express, featuring data analysis, wafer prober control and test suite automation.
-
Product
Noise Figure Analyzer, Multi-touch, 10 MHz to 26.5 GHz
N8975B
Low-Frequency Noise Analyzer
The N8975B high performance noise figure analyzer is designed to make fast, accurate and repeatable noise figure measurements. When paired with an SNS Series noise source and U7227 Series USB preamplifier the ENR data from the SNS and USB preamplifier data automatically downloads into the N8975B.
-
Product
Millimeter-Wave Noise Source, R-band, 26.5 to 40 GHz
R347B
Noise Source
The Keysight R347B noise source covers a 26.5 to 40 GHz frequency range. This waveguide noise source allows you to make accurate and convenient noise figure measurements on millimeter-wave devices. The R347B provides highly precise broadband noise at the input of the system or component under test. The noise figure meter then processes the ON/OFF ratio of noise power present in the system IF, and provides an accurate reading of noise figure and gain. The R347B noise source has remarkable ENR stability over time, which allows longer recalibration cycles and more accurate noise figure measurements.
-
Product
Noise Figure Analyzer, Multi-touch, 10 MHz to 40 GHz
N8976B
Low-Frequency Noise Analyzer
The N8976B high performance noise figure analyzer is designed to make fast, accurate and repeatable noise figure measurements. When paired with an SNS Series noise source and U7227 Series USB preamplifier the ENR data from the SNS and USB preamplifier data automatically downloads into the N8976B.
-
Product
Bridges
-
Equip your testing environment with portable, precise Wheatstone bridges and Kelvin double bridges from Transcat. The Wheatstone bridge is a device containing a divided bridge circuit for taking highly accurate resistance measurements. It captures the value of an unknown resistance, in comparison to known resistors within the circuit. Precision bridges provide exact resistance measurements in the miliohms (m_) to megohms (Mohm) range within their specified accuracies. We offer portable Kelvin double bridges, which are forms of the Wheatstone, designed to measure low resistance – with high accuracy. Transcat also stocks individual resistors, which provide resistance standards in low to high values. They operate in conjunction with potentiometers or bridges.
-
Product
RF Bridge, 75 Ohm, 300 kHz to 3 GHz
86207A
RF Bridge
The Keysight 86207A high directivity 75 ohm RF bridge offers unparalleled performance in a variety of general-purpose applications. It is ideal for accurate reflection measurements and signal leveling applications.
-
Product
Ethernet to Wi-Fi Bridge
BR-500AC
-
BR-500AC is the first commercially available 802.11ac wave2 2x2 MU-MIMO dual-band Ethernet to Wi-Fi bridge supporting WPA3-Enterprise Wi-Fi security. Leveraging advanced features of 802.11ac wave2 standard, BR-500AC securely, reliably, and efficiently connects any Ethernet device to your wireless network enabled by a recent Wi-Fi access point.
-
Product
4-20mA Bridge AmplifierR
90416
-
This miniature, on-board, transducer amplifier is capable of supplying excitation voltage and amplifying millivolt signals from strain gage based transducers.
-
Product
Noise Thermometer
MFFT-1
-
The MFFT-1 magnetic field fluctuation thermometer is a high accuracy thermometer system for typical dilution refrigerator temperature ranges.
-
Product
Modules - Modules, Bridge
-
Vishay’s bridge modules feature voltage ratings from 50 V to 1600 V in single-phase and three phase configurations and in a wide range of package options.
-
Product
Bridge Monitoring
-
Structural Health Monitoring of BridgesDewesoft data acquisition systems are used in structural health and seismic bridge monitoring projects ranging from structural mechanics to continuous monitoring of large, complex structures. The systems provide distributed, high-channel-count and remote monitoring for highway overpasses, roads, buildings, and bridges.
-
Product
Noise Dosemeter
Castle GA257B
-
The SONUS Pocket Dosemeters are designed to be powerful and easy to use. These dosemeters are small and tough so measurements and data can be collected throughout the working period. Data can be reviewed on screen or downloaded to a PC for further analysis. The SONUS GA257B is a dedicated basic dosemeter fully compliant with IEC 61252:1993 and IEC 61672-1:2013, giving simultaneous sound exposure (Lep'd) and maximum peak (Zpeak) measurements, an essential feature for Noise at Work Regulations assessments.
-
Product
Noise Test
-
As experts in the acoustic industry, our company offers a wide range of noise monitoring equipment, including sound level meters, monitoring substations, and noise localization devices. We also provide customized solutions to meet specific scenarios and requirements for noise control.
-
Product
Noise Reduction
-
Applied Research and Technolgy
Eliminate ground hum with our specialized transformers and isolators.
-
Product
Ethernet to Wireless Bridge
BR-100AH
-
BR-100AH is the first commercially available bridge supporting IEEE’s 802.11ah wireless standard which is a long-range technology which enables any Ethernet device to become an 802.11ah wireless network device, giving the freedom to place it anywhere in your facility. BR-100AH is all that you need to incorporate your device into your 802.11ah (HaLow) network. A benefit of 802.11ah is extended range, making it useful for long distance and rural communications.
-
Product
Phase Verification Bridges
5002
-
Clarke-Hess Communications Research
The Model 5002 Phase Verification Bridge set comprises passive devices that are used in conjunction with Model 5500-2 Phase Standard and an output null indicator such as a true rms voltmeter, an oscilloscope or a wave analyzer to verify that the Phase Standard is continuing to operate within its specified phase accuracy limits.
-
Product
Gateways And Bridges
FarLinX Connect Mini v2
-
A compact remotely manageable HDLC Bridge and TCP to HDLC Converter.
-
Product
Noise & Vibration Analyzers
-
The NVA instrument is generally composed of a personal computer equipped with one or more data acquisition board, a conditioning interface and / or to the transmitters power and finally a series of libraries of application software dedicated to the type of measurement to be made. the type of personal computer can be either a desktop, notebook or portable and depending on the particular requirements, you can use the PXI architectures.
