-
Product
HandyScope HS6-DIFF With SureConnect: 100 MS/s, 250MHz BW, 4 Channel (256MS/ch), USB Differential Digital Storage Oscilloscope, Spectrum Analyzer, Voltmeter, Transient Recorder
HS6-DIFF-100XMS-W5
-
- 1GS/s sampling and flexible resolution of 8-16 bit.- Four input channels up to 250 MHz analog bandwidth- Highly accurate 1 ppm time base- DC Accuracy of 0.25 % and 0.1 % typical- Very fast 200 MSamples per second USB streaming Data logger- Spectrum analyzer with 32 million bins- Optional SureConnect connection test on all channels- Up to 256 MSamples memory per channel
-
Product
Oscilloscope - 500 MHz, 4 Analog Channels
DSOX3054T
Oscilloscope
500 MHz4 analog channels Easily view and analyze your signals with on the large 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering See more signal detail with the 1,000,000 wfms/s update rate Capture more data with up to 4 Mpts memory Expand your measurement capabilities with full upgradability: Add bandwidth, digital channels, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis & mask testing at any time
-
Product
Thermo-Hygrometer
C3121P-4
-
Thermometer, hygrometer is designed for direct measurement of temperature, relative humidity for compressed air up to 25 bars with 4 meters cable. Audio and optical alarm of measured values. Memory of minimum and maximum measured values. Function Hold - manual storing of actual values for later displaying.
-
Product
Multifunctional testers
MI 3155 EurotestXD
-
MI 3155 EurotestXD is the newest flagship of Metrel’s most advanced line of multi-functional measuring instruments and is designed specifically for testing in industry. What differentiates this instrument from the rest is its ergonomic design and an intuitive user interface, encompassing a memory organizer and fully programmable AUTO SEQUENCEs, managed through a large colour touch screen display.
-
Product
Logic Analyzer Probe
FS2510AB
-
The FS2510AB is a logic analyzer probe used to test DDR4 DIMM memory. When used with the triggering and analysis capabilities of Keysight’s U4154A/B/64A logic analyzer modules, it gives the user an effective tool for debugging, testing and verifying DDR4 DIMMs.
-
Product
FPGA-Based Ultra-Fast Flash Programmer
XJFlash
-
XJFlash is an FPGA-based advanced and innovative method that uses JTAG for high-speed in-system programming (ISP) of flash memories – all serial and parallel flash devices are supported. The most common use of XJFlash is programming the SPI/QSPI NOR flash used to configure an FPGA.
-
Product
PCIe 16 Bit Multi-purpose Digitizer - up to 5 MS/s on 2 Channels
M2P.5911-X4
Digitizer
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels
-
Product
PCI Express Graphic Card NVIDIA RTX 4000E Ada
NVIDIA RTX 4000E Ada
Graphics Card
- NVIDIA Ada Lovelace Architecture- 5-year Longevity Support- Full height, full length design- PCIe Gen4x16 interface- 20GB GDDR6 Memory, 160-bit Bandwidth- 6144 CUDA Cores, 26.7 TFLOPS SP Peak
-
Product
Protective Bonding Testers
RMO-E Series
-
The RMO-E instruments are designed and ideal for testing protective bonding (grounding) of equipment following the standard IEC 61010-1. Also, they can measure the resistance of high, middle and low voltage circuit breakers, high-current bus bar joints, cable splices, and welding joints. The instruments accurately measure not only in factory environments but also in high-induction fields and substations.Both models generate a true DC ripple-free (less than 1 %) current with automatically regulated test ramps. During a test, the protective bonding testers automatically generate increasing current before measuring and decreasing current after the measurement. Consequently, this significantly decreases magnetic transients and ensures great accuracy.These instruments can store up to 500 measurements in the internal memory and have a built-in thermal printer available as an option.DV Win software communicates with the RMO-E earth resistance meter via USB or RS232 interface. It allows a user to run the test remotely from PC, as well as to download test results, analyze and generate fully configurable test reports.The RMO-E series contains two models, RMO60E and RMO100E. The main difference between these two models is in the maximal test current:60 A DC for RMO60E100 A DC for RMO100E
-
Product
Digital Signal Processor
CHAMP-XD2M
-
Curtiss-Wright Defense Solutions
Imaging sensors, RADAR, and SIGINT provide an overwhelming amount of data that needs to be stored before it can even be processed, but current solutions offer far from enough memory to store it. By providing more memory capacity on a single board, systems can remain SWaP-C optimized and data can be connected and processed with ease.
-
Product
Ultra Fast Digitizer With 8 Bit, 4 GS/s Sampling Rate With Up To 8 GS Memory
CompuScope Express 14G8
-
The CobraMax CompuScope family of GaGe ultra high-speed 8-bit digitizers provides the most powerful combination of speed, memory, and bandwidth as well as a wide portfolio of advanced acquisition features on a single PCI Express or PCI card.
-
Product
RFID Sensor Transponder (HF)
TELID®200
-
With the TELID® 200 range, you can have a combination of RFID transponders and sensors for measuring physical quantities. Here, in particular, pressure, acceleration, strain, moisture, and electric conductivity are of significant interest. Determining the situation just-in-time and storing the newly measured values in the integrated memory is one of its main functions. More complex functions such as digital I/O ports for connecting memories, microcontrollers and digital subsystems are also available. TELID® 200 products do not require batteries and work with no internal energy source.
-
Product
Virtex-5 FPGA with Plug-in I/O
PMC-VFX
-
Acromag’s PMC-VFX boards feature a reconfigurable Xilinx® Virtex™-5 FPGA enhanced with multiple high-speed memory buffers and a high-throughput PCI-X interface. Field I/O interfaces to the FPGA via the rear J4/P4 connector and/or with optional front mezzanine plug-in I/O modules.
-
Product
Emulates AT8xC5122 Derivatives with 6/12 Clocks/Cycle
FE-5122
-
* Emulates AT8xC5122 Derivatives with 6/12 Clocks/Cycle * 32K Code Memory * Software Trace * Real-Time Emulation * Frequency up to 40MHz * MS-Windows Debugger for C and Assembler * Keil Vision2 Debugger Compatible * PLCC-68, PLCC-28, LQFP-32 and VQFP-64 Emulation Headers * Serially Linked to PC at 115Kbaud
-
Product
Metrology System
Echo
-
The Echo system is a comprehensive in-line metal film metrology tool for single and multi-layer metal film measurements in leading-edge logic, memory, advanced packaging, and specialty semiconductor devices.
-
Product
16 or 32 channel Digital to Analog Converter
LS-71-P
-
The LS-71P PCI D/A Converter (DAC) board provides high speed analog outputs of PCM decommutated data allowing real time data displays using strip chart recorders or similar devices. The LS-71-P board is designed to be used in conjunction with the Lumistar LS-50-P Multifunction PCM Decommutator boards and uses an over-the-top communication bus directly from the decom to the DAC to avoid any glitches in the analog outputs due to PCI bus activity. Direct “mailbox” type access is also provided to allow the user to send information through the PCI bus to the DACs. The DAC board design allows 2 LS-50-D Multifunction decom boards to be used with a single DAC board allowing tagged data from either data stream to be directed to any DAC channel. An optional LS-71-DB Word Selector Daughterboard allows two additional data streams to be monitored with the ability to select channels from 4 data streams to be displayed on any DAC channel. The design incorporates an extremely large memory (more than 200,000 16-bit words) used as a lookup table allowing linear or non-linear EUconversions with constant delay regardless of the number of polynomial coefficients required. Standard product supports a single decom, however, dual decom support is available as an option.
-
Product
SSD
CFAST-B-XXG-SI
-
The CFAST-B-XXG-SI is a USA-made product line of Industrial SLC-based CFast memory cards. These small form factor CFast cards provide SATA level performance while featuring robust features needed for industrial applications. These cards contain a locked-down Bill of Materials to ensure consistent product performance and future compatibility.
-
Product
Bench/System Multi-Range DC Power Supply With Digital Control, 3 Or 4 Outputs, 315 To 420W With/without Remote Interfaces
MX Series
-
Three or four high performance outputs each with full functionalityRange switching gives variable voltage/current combinationsShared power mode provides double power from a single outputLow output noise and ripple via linear final regulationHigh setting resolution of up to 1mV and 0.1mAVariable OVP and OCP trips on all outputs50 setting memories per output plus 50 linked memoriesSelectable voltage tracking (isolated tracking)Selectable current meter averagingSwitchable remote sense capabilityGraphic LCD provides simultaneous output meteringNumeric or spin-wheel control of all parametersIndividual or combined output on/off control with programmable delay sequencing.3U half-rack case for bench or rack mounting (4U rack kit accessory available)RS-232, USB and LAN (LXI) interfaces (P models)GPIB option (P models only)Duplicate power & sense terminals at rear (P models)
-
Product
4-Ch Digital Storage Oscilloscope
2553
-
The 2550 Series digital storage oscilloscopes deliver performance and value in 2-channel and 4-channel configurations. With bandwidth from 70 MHz to 300 MHz and 2 GSa/s sample rates, these oscilloscopes offer 24 kpts/Ch waveform memory, 32 automatic measurements, and advanced triggering capabilities including math functions. Engineered to allow you to see more of your signal under test, the 2550 series’ widescreen 7” TFT display offers a significantly larger viewing area than typical economy oscilloscopes (5.7”).
-
Product
DH Series QuickLink Adapter, 8 GHz BW
DH-QL
-
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
500 MHz 4 Channels Oscilloscope
DSOX3054A
Oscilloscope
500 MHz4 analog channels Easily view your signals on the 8.5-inch WVGA display Capture more data with up to 4 Mpts memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add bandwidth, memory, digital channels, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis, segmented memory & mask testing at any time
-
Product
PXI Digital Waveform Instrument
Digital Waveform
PXI Digital Waveform Instruments feature up to 32 channels, can sample and generate digital waveforms at up to 200 MHz, and interface with various standard TTL and low-voltage differential signals (LVDS), as well as settable voltage levels. These devices offer per clock cycle, per channel bidirectional control, and phase shifting. They include deep onboard memory with triggering and pattern sequencing. Some models also support doubledatarate (DDR) technology and real-time hardware data comparison. You can use Digital Waveform Devices to create device simulation and complex stimulusresponse tests.
-
Product
Full DSP-Based 8-Axis Motion Control Universal PCI Card
PCI-1285
PCI Card
Encoder input is 10 MHz for 4xAB mode, 2.5 MHz for CW/CCW modePulse output up to 5 MppsMemory buffer (10K points) for trajectory planning which is designed in DSPSupports E-Gear, and helical interpolationSupports E-CAM providing 256 points to describe the CAM profiles which buffers located in DSPHardware emergency inputWatchdog timerPosition latchPosition compare triggering up to 100 KHz, and memory buffer is up to 100 K points in DSPProgrammable interruptSupports gantry mode by semi-closed loop pulse train controlRDY/LTC-dedicated input channels & SVON/CMP/CAM-DO/ERC-dedicated output channels are switchable for general input and output purposes
-
Product
PCIe FPGA Carrier For FMC, Virtex-7
PCI516
-
The PCI516 is based on the Xilinx Virtex-7 690T, which provides 3,600 DSP slices, 52,920 Kb RAM and 690,000 logic cells. The FPGA interfaces directly to the FMC DP 0-9 and all FMC LA/HA/HB pairs, making it compatible with a wide range of industry standard VITA 57 modules. It also has interface to three DDR3 memory channels (64-bit wide and 16-bit wide). This allows for large buffer sizes to be stored during processing as well as for queuing the data to the host. The unit has x8 PCIe edge connector routed to the FPGA PCIe Gen3 hard IP block. In addition, 16 uncommitted connection pairs are routed to a dual x8 expansion connector, providing direct connectivity to a neighbouring FPGA (e.g. via Aurora, 10 G/40 G, SRIO, PCIe) without the need to go through the host.
-
Product
6U VPX double-GPU Image & Video Processing Board
VP69701
-
LinkedHope Intelligent Technologies Co.,Ltd.
Based on AMD Radeon™ E8860, VP69701 is a VPX double-GPU image & video processing board mainly designed for applications of embedded image & video processing and GPGPU.On VP69701, there are 4 independent display outputs routed to front and 2 GPU. Each GPU of VP69701 is equipped with 2GB GDDR5 video memory, 768/48 GFLOPS single/double precision peak processing ability and 640 shader processing units. VP69701 is highly suitable for HD output (1920x1080), 4K output (3840x2160), high-performance parallel computing and other applications and fields.
-
Product
Ethernet/LXI generatorNETBOX 16 Bit Arbitrary Waveform Generator - up to 40 MS/s on 4 Channels
DN2.653-04
Arbitrary Waveform Generator
The generatorNETBOX DN2.65x arbitrary waveform generators (AWG) is a general purpose multi-channel AWG with outstanding dynamic performance. The series includes LXI units with either four, eight or 16 synchronous channels. The large onboard memory can be segmented to replay different waveform sequences.
-
Product
4-slot Network File Server
CNS4
-
Curtiss-Wright Defense Solutions
The Compact Network Storage 4-slot (CNS4) is a conduction-cooled, high-performance network file server with scalable storage and encryption options. CNS4 is network-agile supporting CIFS, NFS, HTTP, FTP, and PXE protocols making it ideal for sharing critical data in a harsh environment. The CNS4 is designed to accept 4 memory modules and can support up to 8TB of removable solid state storage
-
Product
4/8-CH 12-Bit 1 MS/s Analog Output Multi-Function DAQ Cards
DAQ-2500 Series
-
ADLINIK DAQ-2501 and DAQ-2502 are high-speed and high-performance analog output multifunction DAQ cards. The devices are able to update up to 8-CH, 12-bit analog outputs simultaneously at sustaining 1 MS/s. The reference sources and the output polarities are programmable on per channel basis, combining with the multiplying DAC architecture, ADLINK DAQ-2500 series DAQ cards can generate complex modulated analog signals. The hardware-based arbitrary waveform generation frees the CPU intervention even when all analog outputs are updating at full speed, and the lengths of waveforms are only limited by the system memory. The DAQ-2500 series integrate up to 8-CH, 400 kS/s, 14-bit single-ended analog inputs with programmable polarity, 24-CH programmable digital I/O lines, and 2-CH 16-bit general-purpose timer/counters.
-
Product
COM Express Module
CM22202
-
LinkedHope Intelligent Technologies Co.,Ltd.
CM22202 is a Type 6 COM Express® module developed by LinkedHope® based on China local x86 architecture ZX® KX-6000 series Processors. This module pinout is compliant with PICMG COM.0 R3.0 specification. CM22202 contains all kinds of high-speed interfaces such as SATA III, USB 3.0 and PCIe 3.0. CM22202 provides dual-channel SO-DIMM, supporting DDR4-2666 MHz memory and the capacity up to 32GB.CM22202 supports KX-6000 series 4 core processors which TDP from 25W to 55W. CM22202 provides high performance computing with balanced power consumption. CM22202 works well in a wide range temperature environment. It is ideal for the high-bandwidth and processing intensive requirements of industrial and edge computing applications.
-
Product
SparkFun Mini Breakout
SAMD21
-
If you’re ready to step your Arduino game up from older 8-bit/16MHz microcontrollers, the SparkFun SAMD21 Mini Breakout is a great landing spot. The SAMD21 Mini Breakout is a Pro Mini-sized breakout for the Atmel ATSAMD21G18, a 32-bit ARM Cortex-M0+ processor with 256KB flash, 32KB SRAM, and an operating speed of up to 48MHz. This mini breakout provides you with an Arduino hardware option that solves the problems of low storage limits and dynamic memory stack overflows that have plagued the previous iterations of the Arduino family. Yes, the SparkFun SAMD21 Mini Breakout is even fully supported in the Arduino IDE and libraries for the Arduino Zero!
