Product

The Nanomotor®

-

Klocke Nanotechnik

Klocke Nanotechnik

The patented Nanomotor® is a piezo driven linear motor. It is a multifunctional basic part for many positioning and manipulation devices. It has a positioning stroke of up to more than a centimeter while operating with atomic resolution. The Nanomotor thus bridges eight orders of magnitude. The Nanomotor consists of a cylindrical housing and a slider with a free axial hole inside. It combines high resolution in the sub-nanometer range with a large positioning stroke. The Nanomotor utilizes a piezo tube for fine positioning and a shock wave produced by the same piezo tube for coarse movements. The small Nanomotor is half the size of a match stick. It can lift six times its own mass. Every point of its stroke can be reached with a speed of up to 1 mm/s. The Nanomotor also works in ultrahigh vacuum or even under water. It is driven by a PC card at a supply voltage of only ±15 volts.

Product

4-in-1 OSLT Calibration Kit, DC to 70 GHz, Type-1.85 mm (f)

CK058F

-

Spanawave Corporation

CK058F - Spanawave Corporation

The Network Analyzer Calibration Kits with open, short, load, and thru (OSLT) provide the RF components needed to enable stable and accurate error correct measurements. Calibration of a network analyzer using Spanawave's Network Analyzer Calibration Kits allow for precise measurements. The Calibration Kits offer broad test equipment coverage for use with the 8003 Scalar Network Analyzer as well as being compatible with most network analyzers produced by other manufacturers. Spanawave calibration kits yield complete calibrations, as it takes into consideration the three major sources of systematic error correction by one port calibration at both ports.

Product

Manual Fixture Kit

230355 – CMK-06

-

Columbia Elektronik AB

230355 – CMK-06 - Columbia Elektronik AB

Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.

Product

Standard 1.53 (43.00) - 4.00 (113.00) High Performance Lead Free Probe

LFRE-72T20-4

-

ECT

LFRE-72T20-4 - ECT

Current Rating (Amps): 3Average Probe Resistance (mOhm): 15Test Center (mil): 50Test Center (mm): 1.27Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Overall Length (mil): 1,700Overall Length (mm): 43.18

Product

Incremental Length Gauges For Measuring Stations And Multi-gauging Fixtures

SPECTO series

-

Heidenhain Corp.

SPECTO series - Heidenhain Corp.

*High system accuracy: ±1 µm*Very rugged design*Compact design for limited installation space*Various plunger actuation possibilities*Highly durable ball-bearing guide*Measuring range of up to 30 mm*Interfaces: 1 VPP, TTL*Protection rating of up to IP67

Product

Four-Point Probe

-

Materials Development Corporation

Materials Development Corporation

Materials Development Corporation offers the complete line of Four Point Probe systems from AIT. Systems are available to measue up to 12" diameter (300 mm) wafers as well as specialty systems for Photovoltaic wafers and substrates. For more information on these systems, contact MDC.

Product

Electronic Calibration Module, DC To 9 GHz, 2-Port

N7552A

-

Keysight Technologies

N7552A - Keysight Technologies

Reduce your calibration time by half with a smaller, lighter 2-port module that supports 3.5 mm or type-N 50 Ω connectors

Product

3D Measuring Laser Microscope

LEXT OLS5000

-

Olympus Corp.

LEXT OLS5000 - Olympus Corp.

The OLS5000 laser confocal microscope precisely measures shape and surface roughness at the submicron level. Data acquisition that's four times faster than our previous model delivers a significant boost to productivity. Measure samples that are up to 210 mm tall. Capture the shape of any surface. Total magnification: 54x - 17,280x

Product

Manual Test Adapter With Rigid Needles

-

MicroContact AG

MicroContact AG

Frequently, manual test adapters are required for the functional and IC test. In order to contact the test subject, spring contact probes are often installed in the adapter, but the pitch of the spring contact probes is approx. 1.27 mm and thus too great for certain applications.

Product

LED Solar Simulator

LumiSun-50

-

Innovations In Optics Inc.

LumiSun-50 - Innovations In Optics Inc.

The LumiSun-50™ is a high power, multi-wavelength LED solar simulator that meets IEC 60904-9 Class AAA for spectral match, uniformity of irradiance, and temporal stability. The LumiSun-50 achieves a spatially uniform illumination field from a chip-on-board (COB), multiple-wavelength LED die array. The field of illumination is 50 x 50 mm at a working distance of 200 mm. The LumiSun-50 includes a driver/controller which individually provides constant current to each die in the COB array. Total irradiance of 1.1 sun units is provided and can be decreased to 0.1 suns. The LED light source of the LumiSun-50 is contained within an air-cooled housing that can rotate the angular beam alignment. Adjustment and setting of the optimum light path working distance is visually facilitated by a converging pair of red dot laser pointers.