Scratch
scored mark on a surface.
-
Product
Scratch Tester
CSR1000
-
This tester is highly effective in measuring the adhesion strength (adhesion strength) of hard coatings (Ti, TiN, SiC, DLC, etc.) formed by PVD and CVD on metal surfaces such as cemented carbide. Adopting a scratch test method that allows quantitative measurement with simple operations, the film surface is scratched while increasing the load on the sample surface, detecting film breakage with high sensitivity, and providing the load at which film breakage occurs (critical load). tools and mold tools that require
-
Product
Load Cells
-
Whether you need general purpose, low profile or miniature cells for standard or special applications, you don't have to be an expert in force measurement, because we are. Talk to us about what sort of forces you need to measure, and under what conditions and constraints. We'll walk you through the load cell specification process, quickly and efficiently, and if we don't have what you need on the shelf, we'll be happy to customize an existing product or build a new one from scratch to meet your exacting requirements.
-
Product
Cable Fault Locator
TX2003
-
6 km (19,000ft) 0.5mtr dead Zone Selectable Cable Impedance Warble Tone Generator Rapid Fault Location Large 128x64 LCD with Backlight Scratch Resistant Display Environmental Protection IP54 CE Approved 3yrs Manufacturers Warranty 60 Hours Battery Life
-
Product
kSA Emissometer
-
The kSA Emissometer is designed to quickly and easily generate high-resolution diffuse and specular reflectance and total emissivity maps of MOCVD carriers. Carrier emissivity variation means temperature non-uniformity, which can lead to reduced device yield and possibly complete growth run failure. With the kSA Emissometer, emissivity changes can be tracked to determine carrier end-of-life, without wasting growth runs. The kSA Emissometer also detects unwanted residual deposits after baking, and easily identifies carrier surface defects, scratches, microcracks and pits that are not visible to the eye.
-
Product
Back and Forth Scratching Tester
WGQ-60
-
Shanghai Dean Electrical Co., Ltd
Executive standard: NEMA、JIS; Inspection standard: JB/T4279.15-2008Used to detect the scraping resistance of coating and cable insulation layer of flat wires of 0.800～5.600mm (narrow side) and the silk and enamel covered round wires with nominal conductor diameter of 0.100～5.000mm;Application of SCM control allows for fast operation and strong anti-interference capacity;Sample support table allows for parallel rise and fall, maintaining close contact between the entire plane with sample;Scratching needle is vertical to the paint scraping direction and parallel with sample supporting table;When film is scratched and the action current is ≥5mA, painting scraper would automatically stop scraping;LED would automatically display the number of scraping.
-
Product
DIN Scratching Tool
1538
-
The Elcometer 1538 DIN Scratching Tool has interchangeable carbide cutters for the preparation of specimens to be used for corrosion testing.
-
Product
Handheld Water Quality Meters
LAQUA PH210
-
- Automatic pH calibration - up to 5 points (NIST, USA pH buffers) / up to 6 points (DIN pH buffers) - 0.01 pH resolution- Offset and average slope display - Automatic / manual temperature compensation and temperature calibration function- ORP calibration option- °C & °F temperature readings- Auto log data; built-in memory can store up to 500 data- Auto shut-off (programmable: up to 30 minutes)- Auto stable, auto hold, and real time measurement modes- Calibration alarm (programmable: up to 90 days)- Built-in electrode holder allows 2 electrodes to be attached- Monochrome LCD with white LED backlight: 50 x 50 mm- Casing is IP67 waterproof/dustproof, shock & scratch resistant, non-slip- Powered by 2 x AA batteries- Packaged with electrode and calibration solutions in carrying case- 3 years meter warranty
-
Product
Variable Power Supply
VS3
-
The VS-3 power supply is a very convenient portable, non-isolated “variable source” from 0 volts to 150 Vac or 0 volts to 150 Vdc and rated for up to 3 amps, thus the name VS-3. It is comprised of an illuminated voltmeter that reads to the first significant digit, AC variable system output voltage, DC variable system output voltage, logic output voltage and one sense (continuity) contact monitoring points. Banana jacks for connection of test leads are spaced at intervals that allow the use of dual banana test plugs if desired. The VS-3 is protected by two levels of overcurrent protection; AC input, and ground fault protection by a GFCI. All circuitry is housed inside a custom designed case made from 16 gauge steel. An Internal fan dissipates heat buildup and exhaust through louvered side vents built into the case. The carrying handle is designed with a “spring return to rest” position and is padded for comfort. The case has been sized for optimum portability and is balanced from the handle during transportation. The case has a powder coated finish that is scratch, chemical and weather resistant. Rubber padded feet support the case when in the upright position and a convenience receptacle is located on the side of the case. A unique feature of the VS-3 is that it contains “Magnet Packs” on the back of the case. These “Magnet Packs” can support the VS-3 and allow it to “hang” from any magnetic metal surface. The VS-3 can be powered by our UPS system, eliminating the need for an extension cord. The ability to magnetically attach the VS-3 near the source of connection and eliminating the need for an extension cord makes the VS-3 a “must have tool” for technicians.
-
Product
Wireless Fiber Inspection Probe
OCI-20BN-W
-
OCI-20BN-W is a portable optical fiber connector inspector for checking fiber and connector end-face cleanliness, ideal for bench top and fiber optic network installation technicians to eliminate error caused by poor quality or improper cleaning.OCI-20BN-W offers excellent viewing on connector/fiber end-face and is able to feature to record and save image/video of fiber end-face; It can be connected to PC or phone by WIFI.More than 40 assorted high-precision tips designed for inspection solutionsAngled/Lengthened tips for awkward positions.Connect smart phone for testing FiberEye2 is the application on an android or IOS smart phone to capture, display and record the fiber end-face image from the Wi-Fi probe.Connect tablet/laptop for testing EFD is the analysis software on Windows tablet/laptop to have dusts, and scratches on end face inspected, analyzed, compiled and reported
-
Product
Hardness & Scratch Resistance
-
Hardness can be defined as a material’s resistance to permanent deformation. In the coatings industry, hardness measurement can be used to determine the resistance of the coating to scratching from general wear and tear and also if a coating is fully cured.
-
Product
AutoGet auto Focus Portable Fiber Endface Inspector
CA3008
-
CA3008 Autoget is an intelligent portable fiber enface inspector. with newest hardware and software, and with functions of auto focus, auto exposure,auto analysis, autogenerate report, auto image transmission, etc. Autoget can clearly find out the defects of fiber endface, such dirts, scratches.
-
Product
Handheld Water Quality Meters
LAQUA PC220
-
- Automatic pH calibration - up to 5 points (NIST, USA pH buffers) / up to 6 points (DIN pH buffers)- 0.01 pH resolution- Offset and average slope display- ORP calibration option- Automatic / manual temperature compensation and temperature calibration function- Automatic (up to 4 points) and manual (up to 5 points) conductivity calibration- Adjustable reference temperature and temperature coefficient- Adjustable cell constant and selectable measurement unit- Conductivity and total dissolved solids (TDS) conversion- Four (4) TDS calibration curves for wide range of applications: EN27888, Linear, 442, NaCl- Two (2) salinity calibration curves: NaCl, Seawater- With real-time clock and date/time stamp for GLP compliance- Auto log data; built-in memory can store up to 1000 data- Auto shut-off (programmable: up to 30 minutes)- Auto stable, auto hold, and real time measurement modes- Calibration alarm (programmable: up to 90 days)- Built-in electrode holder allows 2 electrodes to be attached - Monochrome LCD with white LED backlight: 50 x 50 mm- Phono jack output for connecting meter to computer via PC (USB) cable for data collection and to printer via printer (RS232) cable for printout - Casing is IP67 waterproof/dustproof, shock & scratch resistant, non-slip- Powered by 2 x AA batteries- Packaged with electrodes and calibration solutions in carrying case- 3 years meter warranty
-
Product
Ten Foot Test Leads w/Screw On Alligator Clips
629-10
-
After numerous requests, we are introducing 10 foot version of our popular 629 test lead. This test lead is 10 feet long, with no connectors or reels. This test lead can be deployed for various applications involving the need for a longer reach. Also, there are no connectors or extension plugs to snag, catch or scratch any part of the vehicle.
-
Product
Handheld Water Quality Meters
LAQUA PC210
-
- Automatic pH calibration - up to 5 points (NIST, USA pH buffers) / up to 6 points (DIN pH buffers)- 0.01 pH resolution- Offset and average slope display- ORP calibration option- Automatic / manual temperature compensation and temperature calibration function- Automatic (up to 4 points) and manual (up to 5 points) conductivity calibration- Adjustable reference temperature and temperature coefficient- Adjustable cell constant and selectable measurement unit- Conductivity and total dissolved solids (TDS) conversion- Four (4) TDS calibration curves for wide range of applications: EN27888, Linear, 442, NaCl- Two (2) salinity calibration curves: NaCl, Seawater - Auto log data; built-in memory can store up to 500 data- Auto shut-off (programmable: up to 30 minutes)- Auto stable, auto hold, and real time measurement modes- Calibration alarm (programmable: up to 90 days)- Built-in electrode holder allows 2 electrodes to be attached - Monochrome LCD with white LED backlight: 50 x 50 mm- Casing is IP67 waterproof/dustproof, shock & scratch resistant, non-slip- Powered by 2 x AA batteries- Packaged with electrodes and calibration solutions in carrying case- 3 years meter warranty
-
Product
K1 Robot | Silver Or Black
K1-RB-S/B
-
Aluminium knobs suitable for round and D-shafts, anodized surface, scratch resistance and electrically non-conducting
-
Product
Open Frame Industrial Touch Monitor
OM Series
Industrial Monitor
We team up with AUO® to ensure delivering the products with solid-build quality, which is protected with 7H hardness and an IP65 front panel. Our monitors can easily withstand the hazards of harsh environments, such as water, dust ingress, scratches, abrasions, and metallic dust. On average, these monitors have a mean time before failure (MTBF) of up to 50,000 hours, minimizing maintenance costs.
-
Product
Profile Measurement System
GapGun
-
Third Dimension Software Limited
The GapGun is a laser gauge, profile measurement system that quickly and accurately quantifies local features such as gap and flush, step, weld and mismatch, radii, scratches, seals, dents, rivets and fasteners. It is a proven technology, used worldwide by most major automotive and aerospace OEMs, with over 1,000 units sold.
-
Product
Connectors
-
Criem connectors - needle adapter, scratch terminal, faston post, security cover, retractible tip cover, etc.
-
Product
K1 Shaper | Silver Or Black
K1-SR-S/B
-
Aluminium knobs suitable for round and D-shafts, anodized surface, scratch resistance and electrically non-conducting
-
Product
Fiber Microscope
WL-C400S
-
The WL-C series fiber microscopes use coaxial illumination to provide users with maximum detail. It easily can detect the finest scratches and contamination, making it ideal for critically inspecting polish quality.
-
Product
High Resolution Microscope For Multi-fiber Connector
D SCOPE MT LWD
-
Designed for inspection of MPO connectors, patch-cords or bulkheads, the D Scope MT LWD checks the cleanliness of the connector face and precisely measures the defects on the optical fiber end-faces. Using Deep Learning technology associated with a high-resolution optical bench, the scratch and defect detection thresholds are significantly improved compared to traditional software.
-
Product
Process Recovery
-
Let us help you recover bracketed product. Whether it is finding contaminants, removing contaminants, repackaging, relabeling, stamping, or some other activity that needs to take place so you don’t have to dispose of product and start from scratch, FlexXray can save you time and money.
-
Product
Sliding Peel Strength Tester
OST3000
-
Compared to the scratch test, the friction and wear test is considered to be a durability evaluation method that is closer to the actual situation
-
Product
K1 Dimple | Silver Or Black
K1-DM-S/B
-
Aluminium knobs suitable for round and D-shafts, anodized surface, scratch resistance and electrically non-conducting
-
Product
Intelligent and Unidirectional Scrape Tester
ZDG-25
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.3-2008/IEC60851-3Inspection standard: JB/T4279.9-2008Meet GB/T6109-2008 standard requirementsUsed to test the film scrap resistance of enamelled round wires with nominal conductor diameter above0.250mm;Application of SCM control，enter the weight value, operation will be completed automatically: put down the scraping rod, stop while film scratch, calculate and show the scraping force, raise the scraping rod, return to zero, sample rotates 120°and repeat the same operation, calculate and show the scraping force of three times and average scraping force.When film is scratched, film scraper would automatically stop scraping, with exposed conductor of sample＜3mmWith the advantages of high sensitivity, good repeatability, stable and reliable characteristics.
-
Product
Handheld Water Quality Meters
LAQUA PH220
-
- Automatic pH calibration - up to 5 points (NIST, USA pH buffers) / up to 6 points (DIN pH buffers) - 0.01 pH resolution- Offset and average slope display - Automatic / manual temperature compensation and temperature calibration function- ORP calibration option- °C & °F temperature readings- With real-time clock and date/time stamp for GLP compliance- Auto log data; built-in memory can store up to 1000 data- Auto shut-off (programmable: up to 30 minutes)- Auto stable, auto hold, and real time measurement modes- Calibration alarm (programmable: up to 90 days)- Built-in electrode holder allows 2 electrodes to be attached- Monochrome LCD with white LED backlight: 50 x 50 mm- Phono jack output for connecting meter to computer via PC (USB) cable for data collection and to printer via printer (RS232) cable for printout - Casing is IP67 waterproof/dustproof, shock & scratch resistant, non-slip- Powered by 2 x AA batteries- Packaged with electrode and calibration solutions in carrying case- 3 years meter warranty
-
Product
Torque Transducers
-
Interface offers both reaction and rotary style torque transducers.Whether you need torque transducers for rotary torque, axial torsion or reaction torque, you don't have to be an expert in torque measurement, because we are. Talk to us about what sort of torque you need to measure, and under what conditions and constraints. We'll walk you through the specification process, quickly and efficiently, and if we don't have what you need on the shelf, we'll be happy to customize an existing product or build a new one from scratch to meet your exacting requirements.
-
Product
2-26.5 GHz Traveling Wave Amplifier
1GG7-8045
Amplifier
The 1GG7-8045 is a broadband GaAs MMIC Traveling Wave Amplifier designed for high output power and moderate gain over the full 2 to 26.5 GHz frequency range. Seven MESFET cascode stages provide a flat gain response, making the 1GG7-8045 an ideal wideband power block. Ebeam lithography is used to produce gate lengths of ~0.3 mm. The 1GG7-8045 incorporates advanced MBE technology, TiPtAu gate metallization, silicon nitride passivation, and polyimide for scratch protection.
-
Product
Welcome To GLCD Font Creator V1.0.0
-
GLCD Font Creator is the ultimate font creation utility for embedded systems. It lets you create fonts for Liquid Crystal Displays (LCD) and Graphic LCD. It provides a very nice and intuitive user interface. GLCD Font Creator lets you create fonts and symbols from scratch, or by importing existing fonts on your system. It lets you modify and adjust them for your needs, apply effects to them, and finally export them as source code for use in your favorite language compiler.
-
Product
Leadframe Inspection Machine
IV-L200
-
The IV-L200 is a leadframe inspection machine ideal for measuring leadframe dimension and pitch. Aside from identifying leadframe warpage, it is also used to detect bent or skewed leads as well as surface defects such as scratch, ink, and contamination, among others.
