Bluetooth Low Energy
minimal power required WPAN. Also known as: BLE,Bluetooth Smart
See Also: Bluetooth, Bluetooth Test, WPAN
-
product
Energy Management System
This intelligent energy management software control system is designed to reduce energy consumption, improve the utilization of the system, increase reliability, predict electrical system performance, and optimize energy usage to reduce cost.
-
product
LXI Low Thermal EMF Matrix 1-pole 42x33
60-510-002
The 60-510 is a high density 1-pole matrix module controlled via LXI. It has excellent thermal stability and substantially reduced thermal EMF figures when compared to a conventional switching matrix. Typical applications include signal routing in ATE, selecting thermocouple inputs, switching amplifier gain circuits and high accuracy DC micro-volt measurements. Ruthenium reed switches are used because of their good low level switching capability. They also have a very long life with excellent contact resistance stability, minimal wetting current and low thermal offset.
-
product
Low Temperature Gas Source
Get a low-cost means to introduce a gas without thermal pre-cracking using Veeco’s low-temperature gas source for molecular beam epitaxy (MBE) systems. The source features a large conductance tube for fast gas switching and a diffuser end plate for good growth uniformity. It is an ideal gas injector for CBr4 for carbon doping in GaAs and NH3 for GaN growth, as well as any other gases that do not require thermal pre-cracking. Enhance system capabilities further by combining the source on one mounting flange with an Atomic Hydrogen Source or 5cc Dopant Source.
-
product
Low Voltage Harness Tester
CR
Test complex assemblies with thousands of points. The system supports guided assembly with on-screen connector images, guidance LEDs on the assembly board, and immediate graphical and audible feedback to catch errors as they occur.
-
product
Low PIM Coaxial Switch, DC to 20 GHz, SP4T
87104Q
Low passive intermodulation (PIM) is crucial for applications where two or more transmitted signals share a common antenna or whenever the transmitter signal is too high or the receiver is sensitive to high intermodulation. The Keysight 87104Q is a low PIM SP4T coaxial switch, operating from DC to 20 GHz, which can help to keep the system PIM level low. A guaranteed 0.03 dB insertion loss repeatability and 3 million cycles of operating life ensures signal integrity, improves testing efficiency and ultimately maximizes test throughput.
-
product
Low Ohms VOM
260-6XLM
Designed for the special needs of solid-state circuitry measurements, the 260-6XLM has extra low power ohms ranges. It also offers all of the advantages of the standard 260 family, including a resettable overload protection circuit on the 260-6XLPM. Both versions come with batteries, manual and test leads with alligator clips.
-
product
Vernier Energy Sensor
VES-BTA
Vernier Software & Technology, LLC
The Vernier Energy Sensor offers an easy way to quantify voltage, current, power, and energy output of small wind turbines and solar panels such as those used in our KidWind Experiment Kits.
-
product
Bluetooth Tests
Devices that are equipped with Bluetooth® technology must, on the one hand, meet the respective country-specific regulatory test requirements, such as B. in accordance with FCC, ISED or CE, as well as test requirements of organizations such as the Bluetooth® SIG or the CTIA have to pass and meet in order to obtain market approval.
-
product
Ferrite Low Frequency Transducers
Ceramic magnetic design able to provide high-power handling and low distortion for the most demanding speaker manufacturers.
-
product
Low Profile PCI Express 2-Port RS-232, RS-422, RS-485 Serial Interface
7205e
The 7205e low-profile PCI Express serial interface provides two serial ports configurable for RS-232, RS-422 or RS-485. Each serial port utilizes a 16C950 UART with 128-byte Tx/Rx FIFOs that enables data rates to 921.6K bps for reliable high-speed communications in data-intensive applications. This high-performance UART includes 9-bit framing support and is fully software compatible with legacy 16550 applications. In addition, the 14.7456 oscillator and UART’s flexible clock prescalar supports the widest range of standard and non-standard baud rates.
-
product
The Ultra Low Noise Streamer
Sentinel® RD
Providing an unsurpassed signal-to-noise performance, Sentinel RD is the best-in-class solid streamer available on the market. In both calm and adverse weather conditions and irrespective of towing depth, Sentinel RD produces the highest-quality seismic data, resulting in the clearest seismic image.
-
product
RL78 Family Of 8/16-bit Ultra-Low Energy MCUs
RL78/D1x (Automotive Only)
Renesas is introducing the RL78/D1x as an optimized solution for the BRICs and low-end instrument cluster markets. The RL78/D1x is the successor of 78K0/Dx2 or UPD78082x microcontrollers and suited for car instrument cluster, built-in car instrument cluster dedicated features such as Sound Generator, Stepper Motor Controller/Driver and LCD Segment Controller/Driver etc.
-
product
Bluetooth Integrated Metal Detector
Bluetooth with Memory Integrated Wireless Connectivity 4 in 1 Multifunction Metal Detector
-
product
Energy Monitoring
Efficient energy monitoring provides the basis for your energy management. Our coordinated measuring devices save a great deal of effort when it comes to energy data acquisition.
-
product
Low Temperature Retraction Tester
EKT-100TRB
EKT-100TRB-Low Temperature Retraction Tester is designed in accordance with ASTM D1329, ISO 2921 with fully automatic and computerized controlling system.
-
product
Low PIM Coaxial Switch, DC to 20 GHz, Matrix
87606Q
Low passive intermodulation (PIM) is crucial for applications where two or more transmitted signals share a common antenna or whenever the transmitter signal is too high or the receiver is sensitive to high intermodulation. The Keysight 87606Q is a low PIM matrix coaxial switch, operating from DC to 20 GHz, which can help to keep the system PIM level low. A guaranteed 0.03 dB insertion loss repeatability and 3 million cycles of operating life ensures signal integrity, improves testing efficiency, and ultimately maximizes test throughput.
-
product
Low Voltage Differential Oscilloscope Probes
Differential signaling used in high speed serial standards requires very accurate characterization. The industry-leading bandwidth and signal fidelity found in a Tektronix low voltage differential oscilloscope probe ensures that you see every possible detail. Tektronix offers TriMode™ architecture which streamlines measurement acquisition by enabling you to make differential, single-ended, and common mode measurements with a single connection!
-
product
Fully Automatic Close Link Single Phase Energy Meter Test bench
SY8125
Hong Kong Songyang Industrial Ltd.
The devices are fully made by aluminum alloy materials and the table board is composed of fireproofing and heat-proof materials. ● The output voltage and current use soft startup and stop. It has the protection functions of voltage short circuit, current open circuit and power amplification exception.● The device has the features of high stability, good reliability and large output power. ● High level of autoimmunization. The coexistence of special small keyboard and PCs, convenience to use.
-
product
Low Phase Noise Reference Source
96270A
The 96270A RF Reference Source is the simplest, most accurate and cost-effective single instrument for calibrating spectrum analyzers and RF power sensors and more, up to 27 GHz.
-
product
LVDS (Low Voltage Differential Signaling) Drivers and Receivers
LVDS (Low Voltage Differential Signaling) Drivers and Receivers from Analog Devices offers designers robust, high speed signaling for single-ended to differential solutions for point-to-point applications. Our selection of products conform to the TIA/EIA-644 LVDS standard and contain the first LVDS transceivers to meet 8 kV IEC ESD performance standards - important for robust, interboard applications where the connectors can be exposed to more harsh electrostatic environments. Companion differential line receivers and differential line drivers support up to 600Mbps. LVDS greatly improves noise immunity and minimizes emissions for high speed point-to-point data transmission and is a low power alternative to emitter-coupled logic (ECL) or positive emitter-coupled logic (PECL) signaling.
-
product
Linear Bench Power Supplies Triple Output, Local Control, Ultra Low Ripple/Noise
Series MPS
Series MPSThe MPS is a 70 Watt, triple output MIL-STD-461 compliant power supply specifically designed to meet the needs of IC/microprocessor experimenters. It is actually two linear (series pass) power supplies in one.The first has a single 0-6V, 0-5A output backed up by an adjustable current limiter and overvoltage crowbar for digital work. The second has two tracked outputs, 0 to +20V and 0 to -20V, both rated at 0-1 Amp. The two power supplies are completely isolated from each other, sharing only the front panel meters and the chassis.
-
product
Bluetooth® Enabled ORP/REDOX & Temperature Pen
UltrapenX2™ PTBT3
*Accuracy of ± 10 mV ORP*3 Calibration Options with Automatic Solution Recognition*Automatic Temperature Compensation in Calibration Mode*99.9% Pure Platinum Electrode*Measurement Storage with Time, Date and Location*Export Stored Measurement Data Via Email*Live or Hold Mode – User Selectable*Proprietary Sensor Design*Rugged Design with Aircraft Aluminum Body*Durable, Epoxy Encapsulated Electronics*Powered by One N Type Battery (Included)*Waterproof
-
product
Low Voltage Power Supplies
We offer low-voltage power supplies in the power range up to 100,000W (customer-specifically even higher). , They are designed for maximum output voltages of 6.5V to 350V and are continuously adjustable from zero to maximum. Our low-voltage power supplies can be operated in constant voltage mode as well as in constant current mode. This enables unlimited operation at any time with the maximum current that can be supplied (even in the event of a short circuit). They are suitable for ohmic loads as well as inductive or capacitive loads and are characterized by a service-friendly design,
-
product
Light and Energy Meter
Model 659
UV Light and Energy Meter for use with all wafer steppers. For over 45 years, OAI is a world leader in UV Light and Energy Measurement Instrumentation used for reliable accurate calibrated control of the photolithography processes in the Semiconductor, MEMS, Wafer Packaging and Wafer Bumping Industries. The New Model 659 is an advanced UV exposure analyzer specifically designed for use with all wafer steppers including high intensity wafer steppers. This meter averages up to 400 exposure readings, has Ethernet and USB interface for downloading recorded measurements, and has intensity range of up to 7,500mW/cm2. Probes are available in wavelength of 365nm, 400nm, 420nm & 436nm. OAI has a complete certified calibration lab to maintain the performance, quality and reliability of our meters. The Model 659 meter is traceable to NIST standards.
-
product
MPOD Universal Low And High Voltage Power Supply System
MPOD--LVHV
In addition to the well established 6-, 8- and 12- channel "medium power" low voltage power supplies of the PL506, PL508, PL512- and MARATON - series WIENER presents with Mpod a new, universal multi-channel low voltage (LV) / high voltage (HV) power supply system.
-
product
Electric Servomotor Type Full Tooth Low Speed Rotational Torsion Tester
This test machine is a test machine that can reproduce the meshing of all gear teeth, such as transmissions, during actual driving.
-
product
Mini Low Profile Load Cell Universal/ Tension or Compression
MLP SERIES
The model MLP Series load cells were designed with economy as first priority. They are a scaled down version of our successful LPO Series Load Cells. MLP-10 through MLP-300 are anodized aluminum and the MLP-500 through MLP-1K are made from 17-4ph heat treated stainless steel. The unique low profile design of the MLP Series provides excellent stability for in line applications for tension and/or compression, while saving space at the same time.
-
product
Pyroelectric Energy Sensors
Our pyroelectric energy sensors use innovative, patented technology which facilitates accurate and repeatable laser measurements of pulses over an extensive range of conditions including long pulses to 20 ms.
-
product
PC Controlled Low Voltage Testers
PC Based Testers Low Voltage Introduction. The PC based analyzers provide high-speed testing for wire harnesses, backplanes, and printed-circuit boards.
-
product
Low Input Bias Current Op Amps (≤100 pA)
Low input bias current op amps are required whenever the difference of currents or voltage is small and needs to be measured accurately. These op amps are used so that the signal is not loaded down by the input of the op amps. Low input bias current op amps are critical for interfacing sensors in applications from photodiodes, pH meters, or other electrometer related functions to downstream electronics. Analog Devices has many precision op amps that fit the definition and range of these applications.
