Gas Chromatographs
vaporize a compound's components and analyze gas emitted.
-
Product
Fixed Digital Gas Detector
OLCT 10N
-
Teledyne Gas & Flame Detection
The OLCT 10N is a digital combustible gas detector designed for to detect combustible, toxic gases or oxygen. Intended for use in combination with the MX 16, MX 32 and MX 43 controller, the OLCT 10N provides a fast and accurate response.All transmitter information is received by the controller in less than 1 second.Non-intrusive operator interface requires only a simple magnetic wand and allows one man calibration without opening the enclosure.
-
Product
H2 and Binary Gas Analyzers
-
PST offer a range of hydrogen (H2) and binary gas analyzers utilising the thermal conductivity property of gases to determine the concentration of a Target Gas (hydrogen for example) within a known Background Gas such as oxygen, nitrogen or argon.
-
Product
Ar Gas Cluster Ion Source
GCIS
-
The Kratos Ar Gas Cluster Ion Source (GCIS) is optimised for depth profiling organic materials in Arn+ cluster mode and inorganic materials in Ar+ monomer mode, dependent on the operating parameters defined by the user and the type of material to be profiled. In Arn+ ion cluster mode the ions can be accelerated up to a maximum of 20 keV. This enables the successful sputter depth profiling of the widest range of polymer materials to be undertaken. However, Arn+ cluster depth profiling has been shown to give very low sputter yields for inorganic materials. In order to retain the capability of generating depth profiles from this class of materials this ion source can also be operated in the more conventional Ar monomer (Ar+) mode.
-
Product
Gas Flow Sensors
ESRF-HF Transmitter
-
The ESRF-HF is a family of mass flow transmitters which enable fast and accurate measurements of gas flow over a wide dynamic range. Each transmitter integrates a MEMS flow sensor and readout electronics inside a housing with very small form factor made from stainless steel. The duty pressure of the flow transmitter is 11bar. All measurement data are fully calibrated, and temperature compensated on board, leading to a reduced temperature coefficient and high measurement accuracy.
-
Product
Mid-Range Gas Filter Correlation CO2 Analyzer
Model N360M
-
Teledyne Advanced Pollution Instrumentation
The Model N360M measures carbon dioxide (CO2) by comparing infrared energy absorbed by a sample to that absorbed by a reference according to the Beer-Lambert law.The N360M uses Gas Filter Correlation (GFC) to overcome the interfering effects of various other gases (such as water vapor) that also absorb IR. The analyzer passes the IR beam through a spinning wheel made up of two separate chambers: one containing a high concentration of CO2 known as the reference, and the other containing a neutral gas known as the measure. The concentration of CO2 in the sample chamber is computed by taking the ratio of the instantaneous measure and reference values and then compensating the ratio for sample temperature and pressure. A nitrogen purge system is provided for the GFC wheel assembly to eliminate the effects of ambient CO2, if necessary.
-
-
Product
Trace Moisture Analyzers for Natural Gas Quality and Petrochemical Applications
-
Michell Instruments’ process moisture analyzers provide continuous, online monitoring of dew point and trace moisture content.
-
Product
SF6 Gas Purity Detector
JH4000CD-1
-
Xiamen Jiahua Electrical Technology Co.,Ltd
Purity of SF6 gas is not only a major item for gas quality acceptance and evaluation of equipment installation and maintenance process, but also a reliable accordance for internal troubleshooting. According to gas purity changes, it can be judged whether the equipment has any serious fault.
-
Product
FTIR Exhaust Gas Analyzer Direct Measurement Type
FTX-ONE-CS/RS
-
The FTX-ONE offers a 5Hz sampling rate and simultaneously measure the concentrations of multiple components including NH3, CH4, and CO2, from (engine) direct exhaust gas using the Fourier Transform Infrared (FTIR) method in combination with multivariate analysis algorithm.
-
Product
Gas and Leak Detection
-
Is used to determine if and in some cases where a leak has occurred in systems which contain liquids and gases.
-
Product
Gas Meter Synthetical Test Bench
SY8506
-
Hong Kong Songyang Industrial Ltd.
The test of the error of the rate of flow:Using the gas flow standard device (in the shape of the bell prover) as our standard equipment, we can figure the standard volume of the tested gas by using the high-precision revolving encoder to measure the descending displacement of the bell prover.
-
Product
Gas Leak Detectors
-
A gas leak detector is a safety device that identifies leaks of combustible or toxic gases and alerts people to the danger. It uses sensors to find leaks of gases like natural gas, propane, or methane.
-
Product
Tracer Gas Leak Testers
-
At ATEQ, we understand how essential it is to detect hydrogen leaks as swiftly as possible. For this reason, we carry our own high-quality gas tracer equipment. One of popular tools is the H 6000, which is a multipurpose, handheld hydrogen leak detector designed to identify a broad spectrum of hydrogen gas concentrations. You can use this instrument for multiple applications like automotive and HVAC.
-
Product
Industrial 4 Gas Combustion Analyzer
K905
-
UEi Test & Measurement Instruments
Hand-held indusrial Combustion analyzer with Wireles communication option
-
Product
Point IR Gas Detector
IR400
-
The IR400 Infrared (IR) Point Detector is a hydrocarbon gas detector that continuously monitors combustible gases and vapors within the lower explosive limit (LEL) and provides alarm indication.
-
Product
Motor Exhaust Gas Sulfur Analyzer
MEXA-1170SX
-
The MEXA 1170 SX is a new instrument used to measure sulfur for after treatment and transient lubricant oil consumption. The analyzer uses ultraviolet fluorescence (UVF) for detection and it can be operated in a total sulfur mode, analyzing sulfur oxides, hydrogen sulfide and all organic sulfur compounds. An inorganic sulfur mode will analyze hydrogen sulfide and the sulfur oxides. The final operational mode will analyze just the sulfur oxides. Any one of these modes can be selected by the user from a front panel interface.
-
Product
Gas Distribution Panels
PTS DII
-
PTS DII Gas Distribution Panels are similar to our PAO-DII Fluid Distribution Panels. They are designed to individually distribute, monitor, and protect one or more of your valuable products from the higher than required flow of a larger PTS, Portable Temperature Servo Conditioner or HPG, High Pressure Gas Conditioner. You can also use PTS-DII Gas Distribution panels with any other source of temperature controlled gas, including a competitor's air or gas source.
-
Product
Manometric Gas Sorption Analyzer
IMI-FLOW
-
The IMI-FLOW combines the manometric gas sorption capabilities of all IMI analyzers with flowing mode operation and integrated mass spectrometry. Manometric mode offers high accuracy isotherm determination to 200 bar, while the flowing mode provides complete control of pressure, composition and flow rate. Integrated mass spectrometry allows downstream gas analysis for TPD and advanced methods.
-
Product
Quadrupole Mass Spectrometer for Residual Gas Analysis
RGA Series
-
Systems for the examination of components present in a vessel or evolved from a process. HALO RGA – for residual gas analysis. 3F Series RGA – triple filter mass spectrometers for analytical applications. 3F-PIC – pulse ion counting detection for fast event studies. Measures the concentration of gases and vapours in real time.
-
Product
Dual Display Digital Pressure Sensor [For Gas]
DP-100
-
Panasonic Industrial Devices Sales Company of America
The DP-100 Dual Display Digital Pressure Sensor is a highly accurate and reliable Pressure Sensor that is equipped with a new visual display that features a wider viewing angle and improved clarity. The pressure and set range part of the display has also been increased as another improvement. The DP-100 Series also offers a multi-function type that enables the selection of analog output (voltage/current) or external input (auto-reference/remote zero-adjustment) to comply with a wide range of applications.
-
-
Product
High-grade type Gas Monitor for Chamber Cleaning End Point Monitoring
IR-400
-
The IR-400 offers real-time monitoring of the chamber cleaning end point during the deposition process. By optimizing the cleaning process, the IR-400 reduces cleaning time and gas usage. This reduction in cleaning gas usage leads to a reduction in chamber damage and increases the life times of all the systems components.
-
Product
Ozone Gas Delivery Systems
-
MKS ozone gas delivery systems provide field-proven, high concentration, ultra-clean ozone generation for advanced thin film applications such as Atomic Layer Deposition (ALD), Chemical Vapor Deposition (CVD), Tetraethyl Orthosilicate (TEOS)/Ozone CVD (HDSACVD), contaminant removal and oxide growth. Gas delivery models have integrated ozone concentration monitoring, flow control, and power distribution. Additional system options include safety monitoring, status indicators and ozone destruction capability.
-
Product
Gas Analyzers for Diving & Medical
-
PST offers handheld, portable and fixed gas analyzers for the diving and medical markets. They are easy to use and ensure diver and patient safety.
-
Product
Gas Permeability Tester
QT-GPT
-
Gas Permeability Tester- QT-GPT series is used to test the gas transmission rate (GTR) of packaging material by differential pressure method.
-
Product
Motor Exhaust Gas Analyzer
MEXA-1300R
-
MEXA-1300R is a motor exhaust gas analyzing system for two and four stroke engine assembly lines and has an integrated sample handling system for removal of oil and moisture. The measurement of CO, CO2, HC and O2 (optional) in exhaust gases is made simply by inserting the sample probe into the tail pipe. AFR and Lambda are also calculated from the exhaust gas concentrations.
-
Product
Transportable Gas Analyzer
CGT-7100
-
The CGT-7100 analyzer measures the concentration of gases in a continuous way, using a ratio photometric non-dispersive infrared absorption (NDIR) method. All pretreatment parts required for measurement, such as the pump, filter, and electric dehumidifier, are built-in. The analyzer can measure three components including CO, CO2, or CH4 (any two of these) and O2, and is compatible with measurement at 100 vol%. The CGT-7100 has wireless communication capability, so measurement values and charts can be displayed on PCs or smart devices. And measurement data can be exported using a USB flash drive.
