Well
-
Product
Pressure Switches
-
Ashcroft® pressure switches are provided in a variety of configurations to meet most installation requirements in nearly every industry. A long list of choices include differential pressure switches, explosion-proof pressure switches, NEMA 4 and NEMA 7 rated pressure switches as well as electronic pressure switches.
-
Product
Automatic Antenna Tuner 3.5 kW
DU 3500 AL
-
The DU 3500 AL automatic tuner has been primarily manufactured for an automatic PA, but it can also be used with any manual PAs as well. The tuner is primarily compatible with the OM POWER automatic PA.This tuner was designed for antennas calibrated to HAM BANDs. The maximum power can only be utilized with these antennas. With other antennas, it should be set at a lower power (max. 2kW).The major advantage of the tuner is that during competitions it is possible to change BANDs particularly quickly.
-
Product
MIMIC® IOS Simulator
-
MIMIC IOS Simulator is a command line simulator that fully supports Cisco IOS® software as well as NX-OS, JUNOS, NETCONF, other command line interfaces and SNMPv1, v2, v2c, v3. You can simulate up to 100,000 devices in a single workstation, and an unlimited number of devices can be simulated by distributing it over multiple workstations. You can access devices using Telnet, SSH and SNMP. Changes made using one protocol is reflected in the other.
-
Product
Diode Driver & Laser System Controllers
-
The laser controllers provide a simple method of controlling Lumina and other popular laser diode drivers or full laser systems. They include the ability to easily control current levels, pulse modes, and interlock controls as well as monitor voltage and current levels as well as q-switch triggering, external triggering, sync output, and additional I/O signals.
-
Product
NI-9219, 100 S/s/channel, 4-Channel C Series Universal Analog Input Module
779781-02
Analog Input Module
100 S/s/channel, 4-Channel C Series Universal Analog Input Module - The NI‑9219 is designed for multipurpose testing. With the NI‑9219, you can measure signals from sensors such as strain gages, resistance temperature detectors (RTDs), thermocouples, load cells, and other powered sensors, as well as make quarter-bridge, half-bridge, and full-bridge current measurements, with built-in voltage and current excitation. Each channel is individually selectable, so you can perform a different measurement type on each channel.
-
Product
Four-Wheel Drive Single Roller Dynanometer for Cars with Axle Load of up to 2.4T
MSR 500/2 CAR 4WD (ADD. BRAKE) | VP 230041
-
Maschinenbau Haldenwang GmbH & Co. KG.
The MSR 500/2 CAR 4WD single roller dynamometer is used in workshops for designers and tuners as well as in educational institutions. It is especially suitable for performance measurements, tuning and diagnostic work on particularly powerful vehicles. With test speeds of up to 300 km/h, it is used for dynamic and static power measurement. The MSR 500/2 CAR 4WD guarantees optimum measurement accuracy and reproducibility through the active measurement of the towing power.The rolling behaviour of the tyre is the same as on the road. Operating methods such as load simulation, including optional modules for the measurement of external data, e.g. driving cycles, are possible.The MSR 500/2 CAR 4WD can also be extended with a 3rd or 4th eddy current brake.
-
Product
Handheld Signal Level Meter
CT-DLM870D
-
The CT-DLM870D is a hand held signal level meter capable of reading analog, digital QAM and digital off air signal levels as well as Carrier to Noise, Bit Error Rate (BER), Modulation Error Rate (MER) and tilt.
-
Product
Racking & Power
-
Maximize system reliability, speed up installs and lengthen product life cycles. Universal or dedicated tvONE solutions: we have got it covered with a wide range of elegant and robust racking, power and cooling solutions including the revolutionary ONErack platforms. Our unique solutions are designed from the drawing board to be at the very heart of all your installations as well as adding elegant finishing touches.
-
Product
Network Service Tester
-
Qosmotec Software Solutions GmbH
The Mobile Network Tester LTS is well suited to verify the functionality, availability and performance of network services and value-added services.
-
Product
Multipin Industrial Connectors
-
Radiall VanSystem designs and produces circular electrical connectors for professional applications and harsh environments to support a wide range of fields including: railways (in rolling-stock as well as signaling applications), machine tools, automation, construction sites, research, power supply, extractive industries, plant engineering. In addition to connectors with screw or bayonet coupling complying with the MIL-DTL-5015 standard, Radiall VanSystem designs and manufactures non-standard interconnection solutions for special applications.
-
Product
Isolated LVDS
-
Isolated LVDS (low voltage differential signaling) devices couple differential signals applied to the LVDS receiver inputs across the isolation barrier to the outputs on the other side and re-transmits the bit stream or clock as LVDS. Analog Devices' drop-in LVDS isolators offer designers robust, high speed differential signaling for point-to-point and multidrop applications. Extending iCoupler® chip scale transformer technology for ultrahigh speed data encoding, these LVDS isolators support a a data rate of up to 2.5 Gigabits per channel for a total bandwidth of 10 Gbps. In contrast to expensive fiber implementations, deserialized links over standard digital isolators or optocouplers, and design-intensive bespoke solutions using transformers or high voltage capacitors, ADI Gigabit Digital LVDS isolators offer the only integrated comprehensive, high performance isolation at 10 Gbps. High performance galvanic isolation for applications include analog front-end (AFE), processor to processor serial communication, or video and imaging data (such as HDMI isolators) as well as isolation between boards, or at a cable interface for LVDS or CML signal chains.
-
Product
Clamp Meters
-
Our clamp meters measure both high and low AC and DC currents as well as earth leakage and earth resistance. With variable jaw sizes, max current readings up to 2000A AC/DC and features including TRMS, data logging and temperature readings we have clamps suitable for a wide range of electrical applications.
-
Product
PCI High Density Pecision Resistor Card, 3-Channel, 3.5Ω To 773kΩ
50-298-143
Programmable Resistor Module
The 50-298-143 is a high density programmable resistor card with 3 channels which can be set between 3.5Ω and 773kΩ with 1Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Digital Light Monitor
LMC-20
-
The LMC-20 functions not only as a light monitor for coating thickness, but also allows control of multi layer/multi material coating processes. Up to 2000 individual layers in a coating are possible, by using 40 program banks of 50 layers each. The characteristics of up to 99 different coating materials can be input as well. Final thickness can be calculated to 1% of a quarter wave.
-
Product
Vector Signal Generator
SMM100A
Vector Signal Generator
The R&S®SMM100A vector signal generator provides remarkably good RF characteristics across the entire frequency range from 100 kHz to 44 GHz. The instrument covers the bands below 6 GHz used by existing wirelessstandards as well as the newly defined bands for 5G NR FR1 and Wi-Fi 6E up to 7.125 GHz and the 5G NR FR2 bands up to 44 GHz.The internal baseband generator in the R&S®SMM100A supports a maximum RF modulation bandwidth of 1 GHz. Digitally modulated broadband signals can thus be generated as required by the prevalent wireless standards. The R&S®SMM100A is well prepared for future bandwidth requirements.
-
Product
RF Adapters
BNC Adapters
-
Amphenol RF offers a wide array of both in-series and between-series BNC adapters in straight and right-angle configurations. 50-ohm and 75-ohm impedance BNC adapters are available with and without panel mounting features. Popular mounting features in bulkhead, both front and rear mount, and 4-hole flange designs. 50-ohm BNC connectors have a frequency range from DC to 4 GHz. 75-ohm BNC connectors optimized for 4K/UHD video applications can perform well to 12 GHz.
-
Product
Low Cost Microwave Wideband APD Preamp Receivers
MR11 (40KHz~18GHz)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
MR11 series microwave wideband optical receiver, adopts high Sensitivity APD diode and Low Noise Preamplifier IC, within bandwidth of 40KHz~18GHz, they are featured with excellent linearity, high responsibility and superior flatness of the RF response in both, power and phase. They provide an outstanding linearity fiber optical communication for analogue wideband microwave application. Due to avoidance of using expensive coaxial cable or wave-guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless, timing and reference signal distribution, telemetry, measurement and delay line etc as well as 10Gb/s high speed communication system.
-
Product
Qualification Testing
-
Qualification, functional, and operational testing are important steps in evaluating how well spacecraft, launch vehicles, and other mechanical/electrical systems perform under severe loading conditions that occur during launch and operation.
-
Product
PCIe-1477, 80-Bit Camera Link, PoCL-Compatible Frame Grabber Reconfigurable Device
786502-01
Frame Grabber
The PCIe-1477 works well for deployment systems and features a user-programmable FPGA for onboard image processing. Placed directly in the image path, FPGAs can acquire and process images with closed-loop control without CPU intervention. This technology is also suitable for high-throughput system architectures to preprocess image data on the FPGA and then send the data to the CPU for further processing and decision-making. The PCIe-1477 also supports Power over Camera Link (PoCL), which you can use to power cameras through PoCL-enabled cables.
-
Product
Blanket Test Equipment
-
Blanket testers are available in models with one through four drawers as well as an eight drawer model with a center control panel. The unit is capable of testing Class 0 through Class 4 blankets.
-
Product
IoT Tester for Cellular & Non-Cellular Technologies
CMW290
-
The R&S®CMW290 is the ideal test solution for the integrated wireless communications modules used in laptops, data cards, wearables and various IoT products. The R&S®CMW290 offers functions tailored to these applications within the R&S®CMW product family. The tester provides network emulation (signaling mode) as well as generator and analyzer functions for the supported cellular and non-cellular standards including GNSS and broadcast technologies.
-
Product
RF & Microwave Test Cables
-
Rosenberger Hochfrequenztechnik GmbH & Co. KG
VNA Test Cables and microwave cable assemblies (RF Coax cable assemblies) must have a high degree of mechanical flexibility in combination with constant electrical stabilities. Such cables are usually used in laboratories for high-frequency measuring applications and test stations, as well as in the areas of telecommunications, automotive, medicine, industry, consumer electronics and aerospace for signal transmission and other applications.
-
Product
Network Attached Storage & Recorders
-
Curtiss-Wright Defense Solutions
Our encrypted, solid-state network-attached storage (NAS) subsystems are designed to reliably provide file services to clients on an Ethernet network in a harsh environment. These NAS solutions protect data-at-rest (DAR) with the industry’s first NIAP Common Criteria (CC) certified 2-Layer encryption, as well as an option for NSA Type 1 encryption.
-
Product
Output Characteristic Analyzer of Electronic Ballast
UI2002
-
• Measure lamp voltage, lamp current, lamp power, oscillatory frequency, filament current, guided cathode current, and crest factors • Measure changing curves and values of startup lamp voltage, lamp current, filament current, cathode current from 0 to 5 seconds, as well as the pre-heat time • Accuracy: Class 2 • Data and curves printable. All the data and curves can be displayed after being connected with PC
-
Product
handheld digital spectrum analyzer
433M
-
RF Explorer is a handheld digital spectrum analyzer, aimed to provide a very affordable tool for work in all ISM popular frequency bands. It is based on a highly integrated frequency synthesizer which offers high performance, compact size, low consumption and low-cost. It has been designed to be used equally well outdoor and indoor, and can be connected to a Windows PC using standard mini-USB for additional features and higher display resolution.
-
Product
Visual Analysis of any Embedded System
SystemView
-
SEGGER Microcontroller GmbH & Co. KG
SEGGER is announcing the release of SystemView, a free tool enabling the visual analysis of any embedded system. SystemView gives complete insight into the behavior of a program, with minimal side effects on the observed embedded system. SystemView offers cycle accurate tracing of interrupts and task start stop as well as task activation and API calls when an RTOS is used. It visualizes and analyzes CPU load by task and interrupts and scheduler. Test setups with LED and oscilloscope are a thing of the past.
-
Product
Channeling Decoder, Nav/Comm/Control Head
RCD200
-
Designed to provide the Avionics shop a simple and expeditious method for testing general aviation radio tuning. Provided are front panel mounted LED's as well as a digital display to provide the quickest code recognition while testing. With this simple method of testing you will soon find yourself testing all your radios and finding those troublesome intermittents. This unit also decodes altitude and ARC 1000 serial data. Click on picture for larger view.
-
Product
Limits and Scanners
-
Watlow Electric Manufacturing Company
Various configurations offer user-selectable or fixed-configuration sensor options including thermocouple, process, RTD and thermal switch inputs as well as user-settable or fixed limit values. Models with displays have user-selectable temperature units. Other features include sensor break protection, industry standard I/O options and UL® and CSA approval. EZ-ZONE models are RoHS compliant. Limits have FM approval for performance in safety limit applications. Watlow limits are designed and manufactured to withstand harsh industrial environments and come with a three-year warranty.
-
Product
Insulation and Continuity Tester
MIT2500
-
The MIT2500 insulation and continuity tester has been designed for motor and cable testing, specialist applications and electrical testing applications, where operation voltages exceed 1000 V and higher insulation test voltages are needed. The MIT2500 offers both fixed range voltages of 50 V, 100V, 250 V, 500 V, 1000 V and 2500 V, as well as a variable range that allows any voltage between 50 V and 2500 V to be "dialled in". This is supported by the new test voltage feedback control, which maintains the output test voltage to within 2% of the selected range, even when under test.
-
Product
Mobile Test Lane
-
Maschinenbau Haldenwang GmbH & Co. KG.
Self-supporting steel container 20 ft. To DIN ISO 668Electro-hydraulic-place incl. Wired remote controlOffice with computer station for inspection personnelHydraulically actuated, sanded entry and exit rampsPC control of test equipment over EUROSYSTEMElectromechanical liftable roof with weather protectionAir conditioning for office (optional)Integrated continuous current unit to supply the complete test as well as the Aufstellmechanik / hydraulics (option)Turning device 360 ° for container (option)Upgradable to a complete test with:
