Glass Thickness
total thickness of laminated or pane of glass.
-
Product
Passive and Active Resistor Trimming for Thick and Thin Film
LRT 2000L
-
*Travel: 6" x 6"*Laser : Fiber Laser Ytterbium 1064 nm*Kerf: 30 to 80 micron Adjustable*Pulse width : 80 nano second*Rap Rate: 1 to 1 million Pulse Per Second*Average Power: 20 watts*Target: Electric crosshair on monitor
-
Product
Leather Thickness Gauge
UI-FT43
-
Leather Thickness Gauge is used to measure the thickness of leather. Place the sample in a thickness meter under a specified load for a certain time and them read the thickness. Unuo Instruments supply film thickness gauge, film thickness gauge, rubber thickness gauge and etc. Shore Durometer for rubber is also available.
-
Product
Glass Break Detection Sensor
ENVIROMUX-GBS
-
Acoustically detects the cracking of glass. Adjustable sensitivity. Includes mounting hardware. Connect to RJ45 or digital input sensor ports. Supports CAT5/5e/6 UTP or STP cables. Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Maximum cable length: 1,000 ft (305 m). Powered by ENVIROMUX-2D/5D/16D.
-
Product
Pfund Thickness Gauge
3233
-
Available in aluminium or stainless steel this instrument consists of two concentric cylinders, one sliding inside the other. A spherical glass lens, which has engraved measurements, is fitted to the end of the central cylinder and when pressed into the wet film, leaves a circular trace.The diameter of the mark on the lens is measured and, using the supplied conversion table, the thickness of the coating can be easily assessed.Ideal for measuring the thickness of wet translucent products such as varnishes, oils etc.Measurement range of 2.25 - 360μm (0.09 - 14.17mils)
-
Product
Thickness and Flaw Inspection
OmniScan SX
-
Olympus is proud to introduce the OmniScan® SX, a flaw detector that benefits from more than 20 years of phased array experience and shares the OmniScan DNA. For improved ease of use, the OmniScan SX features a new streamlined software interface displayed on an 8.4 in. (21.3 cm) touch screen. A single-group and non-modular instrument, the OmniScan SX is easy to operate and cost-effective for less demanding applications.
-
Product
Handheld Gauge for Nondestructive Coating Thickness Measurement
PHASCOPE PMP10
-
The most experienced device in our tactile portfolio – reliably solves all special applications.
-
Product
Film and Paper Thickness Gauges
-
Economical, Accurate, Easy-to-Operate, our line of off-line paper / film thickness gauges are manufactured to meet TAPPI specifications for paper or ASTM specifications for film.
-
Product
Thick Film Divider
GBR-391
-
GBR-391 series high-voltage resistive dividers are made in a thick film technology on ceramic substrates (Al2O3 - 96%) with leads for through-hole mounting. Dividers are characterized by very high maximum voltage, and standard voltage division.
-
Product
Material Thickness Meters
-
Choose from a variety of material thickness meter, mil gage or paint meter products used for the non-destructive measurement of nonmagnetic coating, insulating layer and dry film thickness (DFT) on ferrous and / or non-ferrous metal substrates such as steel and aluminum. Explore PCE Instruments' selection of accurate, affordable material thickness meter, coating thickness gauge, surface testing and film gauge devices used for automotive paint inspection, material testing and manufacturing quality control applications.A material thickness meter is an essential quality assurance tool when anodizing, galvanizing and applying zinc coating to metallic surfaces. A material thickness meter also is used to measure body paint thickness and uniformity on pre-owned cars, revealing repainted spots, identifying hidden damages and exposing undisclosed accidents. This information is important when determining the actual value of a used car. In addition, certain types of thickness meters can measure wall thickness and determine the hardness of metals, plastics and glass.
-
-
Product
Thick Film Passive Element
GBR-250
-
GBR-250 series high voltage resistors are made in a thick film technology on ceramic substrates (Al2O3 96%). These elements are used in high voltage applications.
-
Product
Thickness Gauge
EV 01
-
EV 01 Thickness gauge series are special thickness gauges, with the possibility of many different applications, measuring foot and table.
-
Product
Flaw Detector & Thickness Gauge
DFX-7
-
Automatic: probe zero, probe recognition, and Temperature compensation.Measurement: Variety of modes to address a number of applications.Large data storage with multiple formats: Alpha numeric grid and sequential w/auto identifier.Windows PC interface software.2 year limited warranty.
-
Product
Coating Thickness Gauge - Integral
Elcometer 456
-
Whether you are measuring on smooth, rough, thin or curved surfaces, the Elcometer 456 Dry Film Thickness Gauge produces accurate, temperature stable measurements thanks to its ±1% thickness measurement capability and increased reading resolution.
-
Product
Ultrasonic Thickness Gage
27MG
-
The Olympus 27MG is an affordable ultrasonic thickness gage designed to make accurate, measurements from one side on internally corroded or eroded metal pipes, tanks, and other equipment. It weighs only 12 oz. (340 g) and is ergonomically designed for easy, one-hand operation. Thickness range 0.50 mm to 635 mm (0.020 in. to 25.0 in.) depending on material, transducer, surface conditions, temperature.
-
Product
Current Sensing Resistors, Thick Film Type
-
Panasonic Industrial Devices Sales Company of America
An AEC-Q200 Compliant SeriesPanasonic components specified as AEC-Q200 Compliant are consistently designed into automotive systems. However, today’s Design Engineers are specifying AEC-Q200 components to meet the high-quality standards of devices beyond automotive applications.
-
Product
High Voltage Pultruded Resin Bond Glass Fiber Rod
-
This Test Set-Up can be used to test any kind of Drive Insulator used in Circuit Breaker.
-
Product
Mechanical Coating Thickness Gauge
211
-
This is one of the most popular mechanical coating thickness gauges in the world.Factory calibrated - with user calibration adjustmentFoils supplied to check calibration on siteIdeal for cold surfaces and underwater useSmall and portable with an accuracy ±5%The “V” grooved base, ideal for pipeline inspectionAvailable in either Metric or Imperial versions, the Elcometer 211 measures coatings up to 6mm (250mils)
-
Product
EHC-03 Basic Corrosion Thickness Gages
EHC-03
-
Danatronics is pleased to welcome our EHC-03 to our corrosion thickness gage family. The EHC-03 is designed to accurately and non-destructively measure metal structures subject to corrosion.
-
Product
A-/B-Scan Thickness Gauge For NDT
SONOWALL® 70
-
SONOWALL 70 is the first thickness gauge in the market with intelligent probe identification. The extended probe management allows probe-specific information such as DAC-curves, delay lines, and serial numbers to be saved directly in the ultrasonic probe. In addition to various thickness applications, the device can be upgraded to a full-function flaw detector.
-
Product
Thick Film Passive Element
GBR-183
-
GBR-183 series resistors are made in a thick film technology, on ceramic substrates(Al2O3 -96%). Thick film resistors are characterized by a higher stability, and lower noises than a typical carbon resistors. The whole of resistor is encapsulated with epoxy resin by fluidization process. GBR-183 series elements are used both for general, and professional applications.
-
Product
Coating Thickness Gauge
-
Guangzhou Amittari Instruments Co.Ltd
The Basic Type Coating Thickness Gauge AC-110 Series have two types: Type C ( Integral Type ), Type CS ( Separate Type ); Suitable for automotive, paint layer coating thickness measurement; Integral Type suitable for single-hand operation, large probe with large contact surface have better stability, users can get continuous, good repetitive and precise measurements. Separate Type can provide several type probe, measure can be more flexibility. It is a kind of portable measuring instrument, it can quickly, no damage and precise coating, coating thickness measurement. Not only can be usedin the laboratory, also can be used in the engineering field. Through the use of different measuring head, but also can meet the needs of a variety of measurement. Widely used in manufacturing, metal processing industry, chemical industry, commodityinspection and testing field. Is the material protection professional.
-
Product
Thickness Gauges
UMX-2
-
UMX-2 underwater material and coating thickness gauge, designed for offshore inspections, and rated to a depth of 1000 feet (300 meters). The UMX-2 is very versatile, offering both Dual & Single element transducers. Equipped with multiple measurement mode options, the UMX-2 will meet all your application requirements. Onboard 5,000 point data logger, all UMX-2 settings stored for each measurement, along with an actual A-Scan waveform.
-
Product
Radar solution for thickness measurememt of steel & metal
-
Our radar sensor solution determines the thickness and the thickness profile of steel plates, steel strips or steel slabs (up to 1600 °C hot) with an accuracy of up to ±10 µm on the roller conveyor. Thanks to robust radar technology, sophisticated signal processing and intelligent radar algorithms, OndoSense radar sensors achieve this high level of precision in thickness measurement even under the difficult production conditions of the steel industry with smoke, steam, dirt, vibrations, fire and extreme temperatures.
-
Product
Film Thickness Tester
MX Series
-
Qualitest covers a complete and competitive range of Thickness Testers for plastic films, composite films, adhesives, adhesive tapes, laminated films, plastic films, paper and other materials.
-
Product
Film Thickness Measurement
-
Film thickness measurement can be measured using a number of different techniques depending on the thickness and number of layers. In its simplest form a simple measurement can be made of a single layer with a reflective lower surface using interference fringes. For more complex materials with multiple layers interference measurement is still made, but the mathematical deconvolution becomes increasingly important as does the refractive index of each layer.
-
Product
Compact Passive and Active Resistor Trimming for Thick and Thin Film
LRT 2000C
-
*Travel: 6" x 6"*Laser : Fiber Laser Ytterbium 1064 nm*Kerf: 30 to 80 micron Adjustable*Pulse width : 80 nano second*Rap Rate: 1 to 1 million Pulse Per Second*Average Power: 20 watts
-
Product
Inline Thickness Measuring Instrument
TGD
-
Thickness and profile measuring system for use in production lines.For cold and hot rolled strips and sheets. Measuring procedure free of contact.
-
Product
Ultrasonic Wall Thickness Measurement Meters
-
The LaserLinc UltraGauge+™ series of ultrasonic meters and gauges measure wall thickness, layer thickness, and concentricity of plastic, rubber, glass, and metal products. Typical applications include tubing, hose, pipe, insulated wire, cable, and certain multi-layer products.
-
Product
Ultrasonic Thickness Gauge
38DL PLUS
-
The 38DL PLUS is an innovative instrument that signals a new era in ultrasonic thickness gauging. Ideally suited for almost every ultrasonic thickness application, this handheld thickness gauge is fully compatible with a full line of dual and single element transducers. The versatile 38DL PLUS can be used in applications ranging from wall thinning measurements of internally corroded pipes with dual element probes to very precise thickness measurements of thin or multilayer materials with single element transducers.
