RF Spectrum Analyzers
See Also: Spectrum Analyzers, Audio Spectrum Analyzers, Optical Spectrum Analyzers
-
Product
RF Test Spectrum Measurements over CPRI
Integris 3000
-
Most modern cell tower network configurations place the Remote Radio Head (RRH) at the top of the tower and the baseband unit(BBU) at the bottom of the tower. While this configuration is advantageous for both computational efficiency and mitigation of RF loss across the cable, it means the only place along RF can be accessed is at the top of the tower. This forces field technicians to have to climb the tower to measure and debug RF noise problems.
-
Product
Dedicated Analyzer
-
This measuring instrument automatically measures gas volume / internal gas pressure, air content and oxygen concentration for quality control in the bottling process of carbonated drinks, etc.
-
Product
Spectrum Marker Generator
NSG-2
-
National RF, Inc. is pleased to announce the production of a new device, the Type NSG-2 Spectrum Marker Generator. The generator is intended to be used with either spectrum analyzers or communications receivers to mark specific frequency intervals in the RF spectrum. When used with receivers, it is essentially a frequency calibrator, thus making it attractive for use with vintage receivers with analog dials. The NSG-2 provides a leveled amplitude output over nearly 100 MHz of RF spectrum, thus making it ideal to mark frequencies and signal levels on spectrum analyzers. In addition, it may be used with a spectrum analyzer, in lieu of a sweeping type generator, to align lowpass, highpass, and bandpass filters with passbands greater than 20 KHz.
-
Product
UltraCMOS SP6T RF Switch
PE42562
-
The PE42562 is a HaRP™ technology-enhanced absorptive SP6T RF switch that supports a frequency range from 9 kHz to 8 GHz. An external VSS pin is available for bypassing the internal negative voltage generator in order for the PE42562 to deliver spur-free performance. It delivers high isolation, low insertion loss and fast switching time, making this device ideal for filter bank switching and RF signal routing in test and measurement (T&M) and wireless applications up to 8 GHz. No blocking capacitors are required if DC voltage is not present on the RF ports.
-
Product
Netlist Analyzer
GateVision
-
GateVision PRO is the third generation of graphical netlist analyzers from Concept Engineering. Completely rewritten to run on modern 32/64bit platforms, GateVision PRO provides the designer of even the largest chips with intuitive design navigation, schematic viewing, logic cone extraction and interactive logic cone viewing for debug support and design documentation.
-
Product
FMC L-Band RF Receiver
-
Sundance Multiprocessor Technology Ltd.
The Creonic L-band RF receiver FMC card allows to receive RF signals between 925 and 2,250 MHz. It is ideally suited for satellite communication with standard satellite dishes since it includes a DiSEqC driver IC for LNB controlling. The board allows to build receivers with symbol rates of up to 100 Msymbols/s. Due to the low-pin-count (LPC) FMC connector it can be used with any FMC carrier board that supports VADJ=1.8V. The card will be available from Q2/2017.
-
Product
IQ Analyzer
Alyza IQ NH4
-
Wet-chemical analyzer for continuous measurement of ammonium on wastewater treatment plants and rivers
-
Product
TOC Analyzer
QuickTOCpurity
-
Fast, Accurate, Low-maintenance Monitoring of TC, TOC, TIC, and DOC
-
Product
UltraCMOS SP8T RF Switch
PE42582
-
The PE42582 is a HaRP™ technology-enhanced absorptive SP8T RF switch that supports a frequency range from 9 kHz to 8 GHz. An external VSS pin is available for bypassing the internal negative voltage generator in order for the PE42582 to deliver spur-free performance. It delivers high isolation, low insertion loss and fast switching time, making this device ideal for filter bank switching and RF signal routing in test and measurement (T&M) and wireless applications up to 8 GHz. No blocking capacitors are required if DC voltage is not present on the RF ports.
-
Product
Milk Analyzer
LD-LAMA-A10
-
Milk AnalyzerLD-LAMA-A10detects fat, non-fat milk solids, protein, lactose, water content, salts, total solids, density, freezing point, temperature from the raw or boiled milk sample. Accurate results are obtained using small amount of milk sample. It is convenient and simple to install, operate, maintain and calibrate.
-
Product
Thermogravimetric Analyzers
TGA THERMOSTEP ML
-
ELTRA's TGA Thermostep ML is a thermogravimetric analyzer which determinesvarious parameters such as moisture, volatiles and ash at user-definedtemperatures and atmospheres in a single analysis.
-
Product
Battery Analyzers
C7 Series
-
The Cadex C7 Series analyzer tests lithium, nickel and lead-based batteries with custom Battery Adapters. Optional PC-BatteryShop™ records results in real time.
-
-
Product
EMC Analyzers
-
Mains and harmonics analyzer and associated low distortion AC power source for EMC measurements to EN61000-3-2 and EN61000-3-3.
-
Product
HTTP Analyzer
V7
-
IEInspector HTTP Analyzer is such a handy tool that allows you to monitor, trace, debug and analyze HTTP/HTTPS traffic in real-time. It is used by industry-leading companies including Microsoft, Cisco, AOL and Google.
-
Product
RF Amplifier
SA822
-
Hangzhou Softel Optic Co., Ltd.
SA822 860 MHz outdoor distribution amplifiers are mainly used for bidirectional trunk transmission of CATV television image signal, digital TV signal, telephone voice signals and data (or compressed data) signal.
-
Product
27.12MHz RF Power Generators
-
Available in 300W, 600W, 1000W (air-cooled) and 1200W and 2400W (water-cooled). Ideal for Industrial, Medical, and R&D applications. Compact design, rack mount or stand-alone. Browse spec sheets for 300W and 600W.
-
Product
Ozone Analyzer
AQMS-300
-
Concentration in ppb level by utilizing UV photometric absorption technology.
-
-
Product
Power Analyzers
-
At PCE Instruments you will find a power quality analyzer to measure the power in W, kWh or to analyze and measure harmonics. This power analyzer is a multi-function power analyzer device that measure precisely direct current, alternating current, AC-voltage, DC-voltage the intensity of DC or AC, phase rotation and idle, apparent and effective power. The reading of AC power is considered the real value and has a maximum range of 6000 Watts. While a reading is being taken, the polarity changes automatically, if negative values are taken then a minus sign will appear on the device display.Nowadays, power quality analyzers have many features such as, insulated current input, measurement of harmonics, AC and DC current measurement, AC and DC voltage measurement, frequency measurement, phase rotation measurement and idle, apparent and effective power measurement. All this data can also be logged and analyzed with the delivered PC-Software. Power analyzers of the type PCE PA 6000 can determine the energy in single-phase systems.Power quality analyzers of type PCE-GPA 62 allow the energy measurement in symmetrically loaded three-phase systems. Power analyzers of type PCE-PA 8000, PCE-360 and PCE-830 support professional power and energy measurements in single and three-phase systems.Apart from being used as energy-measuring devices, power analyzers like the PCE-830 can also be used for network analysis and the determination of harmonics and phase rotation. On our website you will find other power analyzers used in the field of electronics.
-
Product
RF Switch
HRS-201
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HRS-201 2×1 RF switch, with its high resolution to the RF monitor, it could be widely applied in the system which need to control, switch or redundancy the RF signal.
-
Product
Oxygen Analyzers
-
Teledyne Analytical Instruments
Oxygen Analyzers by Teledyne Analytical Instruments
-
Product
Combustion Analyzers
-
The Seitron handheld analysers Chemist 100 and Novo are used worldwide for boiler fume analysis. All of our analysers are designed and manufactured in Italy to guarantee the highest quality and reliability.
-
Product
Serial analyzer
-
The Serial analyzer sink decodes analog data on a serial bus to serial data. It can be used to monitor and analyze RS232, RS485, MIDI, DMX or other compatible serial buses. The serial analyzer can monitor up to eight sources. When these sources are in sync (all sources are of one (combined) instrument), all captured data will be displayed in chronological order.
-
Product
RF Isolators
-
150 Watt Isolators include 35W Removable Loads, and can mount on 19" x 5.25" panels.200-400 Watt Isolators include 60W Removable Loads, and can mount on 19" x 8.75" panels.
-
Product
RF Bias Burn-In System
-
These systems deliver an unbeatable combination of advantages over a wide range of RF frequencies and power levels. The Automated Multi-Channel RF-Biased Burn-In Test System is a turnkey system that incorporates all of the capability needed for accelerated aging and parametric testing of RF semiconductor devices. Its powerful software elegantly supports data acquisition, storage, and presentation. Accel RF’s customers choose system features to meet their technical needs and capital budget. In addition to cost savings, use of Accel-RF’s solutions accelerate product time-to-market, saving many months of product development.
-
-
Product
Gas Analyzers
-
Independent Handheld 5 Gas Analyzer or use with MODIS™ Link, VERDICT® and VERUS® Bluetooth® link. Fully Portable 5 Gas Analyzer, go anywhere, use anywhere 110 V AC and 12 V powered Internal rechargeable battery, up to one hour of use Ideal for road testing and mobile use Measures exhaust emissions for CO, CO2, HC, O2, NOx and AFR/Lambda Provides an instant assessment of an engine vehicle exhaust and catalytic converter MODIS, VERDICT® and VERUS® Link for enhanced real-time viewing Setup required with included software on USB stick Gather all the evidence required for effective and accurate vehicle diagnostics on one screen in real time View, graph, save and recall data Monitor and reduce vehicle emissions, improve driveability and fuel efficiency There are 255 memory locations in the analyzer to track and print data for the same or many different vehicles Compatible with gasoline, CNG, propane and diesel fuel types Annual calibration and sensor replacement performed at Crystal Lake Northern Repiar enter Meets required industry standard
-
Product
RF Burn-In Services
-
Innovative Circuits Engineering, inc
There are many burn-in services that we offer such as HTOL, RFBL, ELFR, LTOL, etc and our focus on quality and customer service when providing burn-in custom solutions is second to none. We work closely with our customers to make sure we provide them with the best possible burn-in regardless of their lot size or pin count. We can also provide you with other electrical stress tests such as THB and HAST, and we can provide you with comprehensive status reports for your tests as they progress whether they be burn-in, THB, HAST or any other test.
-
Product
RF Device Tester
RF ITS
-
Sterner's automated test management system, combined with integrated RF technology modules, provides full functionality, including: Apply power to the device under test (DUT). Read and write blocks of data to set up and validate product EEPROM using a hard-wired communications interface. Scan transmitting devices or traveller barcodes and write the information to the DUT (the "sign-up process"). Inject an RF signal of known frequency and power level to test receiver sensitivity.
