Design Verification
Examination of design requirement fulfillment.
-
Product
Harness Design and Manufacture
-
When designing an underwater cable harness, there are some factors which need to be considered, and we have produced the following list as a guide for customer information:Component considerations:- Electrical requirements- Mechanical considerations- Quality requirements- Reliability- Design redundancy (contact count)- Connector selection (type and form)- Locking requirements- Backpotting requirements- Waterblocking in moldings- Cable specification- Cable jacket material and compatibility with elastomers- Abrasion resistance- Stiffness profile at termination- Connector format (straight or right angle)- Molding format (straight or at an angle)- Clearance allowance for molding and cable routing- Elastomer compatibility (eg oil filled units)- Metalwork selection re: corrosion and cathodic delamination- Surface finish for metalwork as appropriateOperational considerations:- Operating depth profile (not just max. depth)- Tensile loads- Torsional loads- Bending loads- Bend control requirements (to limit bending at termination)- Deployment and recovery loads- Dynamic loading-Flow turbulence effects.
-
Product
Power Device Analyzer / Curve Tracer For Circuit Design
B1506A
-
The Keysight B1506A Power Device Analyzer / Curve Tracer for Circuit Design is a complete solution that can help power electronic circuit designers maximize the value of their power electronics products by enabling them to select the correct power devices for their applications. It can evaluate all relevant device parameters under a wide range of operating conditions, including IV parameters such as breakdown voltage and on-resistance, as well as three terminal FET capacitances, gate charge, and power loss. The B1506A Power Device Analyzer/Curve Tracer for Circuit Design meets and exceeds all curve tracer capabilities.
-
Product
Design for Testability (DFT Test)
test
Corelis can provide you with design consultation and an analysis of your design for boundary-scan testability. We will review your design and make specific recommendations that if implemented will improve the testability. We can also suggest improvements that will increase test coverage and allow boundary-scan to be implemented in a more cost-effective manner.This service also includes a DFT test coverage analysis that we recommend to do after schematic capture and before PCB layout. At this stage of product development, Corelis provides you with a comprehensive test coverage reports that identifies all of the boundary-scan nets and pins and classifies them as completely tested, partially tested, or not tested. The report also recommends where to add test points (pads) for physical “nails” access if additional test coverage is required.
-
Product
RF Design
-
As wireless continues to be a significant growth opportunity, SILENT works with commercial and industrial manufacturers to ensure time-to-market for RF and wireless enabled products. We design, build, and test RF and wireless solutions - within budget and cost guidelines - for consumer grade products and high performance circuits and systems.
-
Product
Simulating Optical Design Components
Wave Optics Module
-
The Wave Optics Module provides dedicated tools for electromagnetic wave propagation in linear and nonlinear optical media for accurate component simulation and optical design optimization. With this module you can model high-frequency electromagnetic wave simulations in either frequency- or time-domain in optical structures. It also adds to your modeling of optical media by supporting inhomogeneous and fully anisotropic materials, and optical media with gains or losses. It is straightforward to simulate optical sensors, metamaterials, optical fibers, bidirectional couplers, plasmonic devices, nonlinear optical processes in photonics, and laser beam propagation.
-
Product
Design for Test Service
-
Design For Test (DFT) is a technique used to implement certain testability features into a product. Testing House can provide an analysis of the CAD data for testability of your circuit board. Access to a board can be very difficult as boards get smaller and designs get more densely populated. We can work with your design engineer to improve testability and maintain an effective in-circuit test. When access to the board is limited and boundary scan devices are present, we can provide the customer a list of key nodes that will require access in order to provide a very effective test. Our analysis will provide a list of all the accessible test points and an explanation for any nodes declared inaccessible.
-
Product
CableEye Tester Calibration Verification Board | Cable & Harness Tester
CB50
-
Populated with precision resistors, it allows users to determine empirically whether the tester requires calibration. The CB50 may be used on all CableEye models. The CB50 is intended for periodic verification of tester calibration. To ensure that resistance measurements remain accurate, CAMI recommends yearly calibration. However, depending on environmental conditions and usage, testers may need calibrating more or less frequently.
-
Product
Engineering Design & Development
-
TPSA has over 20 years of experience in Engineering Design & Software Development including:Hardware & Software DesignOTPS Acquisition SupportSystems Installation & SupportAircraft Modification/CertificationEngineering Studies & AnalysesFunctional & Systems TestingIndependent Verification & Validation (IV & V)Test Program Set EngineeringReliability & Maintainability (R&M)Engineering Drawings & DataConfiguration Data ManagementReverse EngineeringRequirements AnalysisSupport Equipment (SE)Aircraft Launch & Recovery Engineering (ALRE)Engineering Change Proposal (ECP) ReviewTechnology Insertion (TI)PDR, CDR, FAT, Techeval, OSV Support
-
Product
Structural Engineering And Design
AEC
-
Altair's architecture, engineering, and construction (AEC) solutions offer unparalleled productivity for building and non-building structures with their advanced versatility, integration, and data management capabilities. Our analysis and design solutions simulate responses to a range of dynamic, nonlinear loading conditions, including wind, snow, water, seismic, blast, dead, live, and moving loads – all while ensuring design resiliency and regional code compliance.
-
Product
Design and Fabrication Laboratory
-
Trialon’s on-site Fabrication Shop is equipped with the tools and experienced staff to design and fabricate custom parts, test fixtures or small batch finished product. Our team is ready to provide your organization with a best-in-class experience that will meet tight timeline.
-
Product
LabVIEW Tools for Digital Filter Design and Implementation
LabVIEW Digital Filter Design Toolkit
ITA
The LabVIEW Digital Filter Design Toolkit extends LabVIEW with functions and interactive tools for the design, analysis, and implementation of digital filters. New digital filter users can explore classical designs with the built-in interactive design tools, while experienced users can find a breadth of algorithms, filter topologies, and analysis tools for both fixed- and floating-point digital filters. For fixed-point filters, you can model quantization effects, optimize numeric representation/topology, and deploy the design on a digital signal processor or FPGA using automatically generated ANSI C or LabVIEW FPGA code.
-
Product
Integrated Solution for Digital Switching & Fiber Optics Operational Verification
VERTA
-
When incorporated into defense/aerospace ATE, Verta enables reliable, error-free bus communication and interoperability tests to verify performance of high-speed, optically networked military weapon assemblies.
-
Product
Custom Cabling with the Cable Design Tool
-
The first step to creating a custom cable assembly is by using our free online Cable Design Tool—with this tool, you can graphically design your custom cable assembly by using either our built-in library of standard cable sets or create them from scratch. Once completed, our engineers will generate a competitive quote for your cable requirements.
-
Product
Compact & Flexible Test Systems for FCT,ICT, ISP and Boundary Scan Designed for Easy Integration
LEON Rack
Test System
The LEONRack test system is a flexible test system that could be installed in automation or handling solutions. It is highly flexible and available in three different chassis sizes from low pin count to high pin count test systems. As part of the LEON Family, LEONRack is based on the ABex platform which directly incorporates Konrad analog bus technology and PXI/PXIe in one chassis.
-
Product
EBIRST 200-pin LFH Verification Fixture
93-002-101
-
The 93-002-101 200-pin LFH Verification Fixture is an accessory for the eBIRST range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces switching solutions.. The tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
PAT and Installation Verification Unit
PowerCheck 1557
-
The PowerCheck 1557 is a comprehensive PAT and installation verification checkbox. It carries out ongoing performance checks to ensure accurate measurement between calibration intervals. Fully tests Earth Continuity, Insulation Resistance, RCD Trip Time, RCD Trip Current, Loop, PE Conductor Current, Touch Current and Flash tests.
-
Product
Truck Mounted Static Grounding Verification
Earth-Rite MGV
-
The Earth-Rite Mobile Ground Verification system (MGV) is a unique, patented technology designed to provide automatic confirmation of a positive electrostatic ground connection for trucks collecting and transferring flammable / combustible products.
-
Product
Custom Design
-
RCF professional woofers stand for ultimate performance, highest power handling, and the most advanced technology in the market.
-
Product
Custom System Design
-
We are interested in developing custom versions of our products or in designing completely new systems.
-
Product
Personal Computer Aided Antenna Design
PCAAD 7.0
-
Antenna Design Associates, Inc.
PCAAD 7.0 is a Windowscompatible antenna analysis, modeling, and design software package. It contains more than 50 routines treating wire antennas, aperture antennas, microstrip antennas, arrays, transmission lines and waveguides, and more. These routines are integrated into a menudriven, userfriendly system allowing you to quickly evaluate the performance of a wide variety of antenna types. PCAAD 7.0 includes a 120-page printed user manual which describes the use of the software, provides examples for each of the routines, and lists technical references.
-
Product
System Modeling for Diagnostic Design and Analysis
EXpress
-
eXpress is a comprehensive model-based diagnostics engineering software application providing an environment for the design, capture, integration, evaluation and optimization of complex or large-scale system diagnostics, prognostics health management (PHM), systems testability engineering, failure mode and effects analysis and system safety analysis. eXpress is uniquely suited to influence the diagnostic development for new designs or to exploit the diagnostic challenges of existing legacy systems. Its robust structure facilitates the capture of extensive interdisciplinary design knowledge providing an unmatched ability to corroborate, reuse and re-purpose expert knowledge in performing standardised testability, reliability and maintainability analyses.
-
Product
Electronics Design Software
Altium Designer
-
Professional unified design system, high productivity stress-free environment and native 3D PCB editor. Easily design the most complex and innovative board layouts with advanced and accessible routing tools. Stay at the frontline of innovative technology development with the world's first-and-only support for rigid-flex PCB design.
-
Product
Electronic System Design
ESD
-
Smart connected devices are everywhere, in homes, in transportation, and at work. This means electronic system design (ESD) is having a greater influence on almost every type of product requiring new simulation tools to help achieve electronic, electrical, mechanical, thermal, and connectivity goals. Altair’s simulation-driven design tools enable your team of specialized engineers to collaborate across all aspects of printed circuit board development from concept to manufacturing. Our products streamline your process, eliminate design iterations, and reduce time-to-market.
-
Product
cCf Custom Design
-
Customised solutions to meet your needs. Using our quickCONNECT system as the basis we can develop a customised PEM test system as per your requirements and wishes!
-
Product
Test Instrument for LAN Cabling Verification
MI 2016 Multi LAN 350
-
High performance, multifunction test instrument for LAN cabling verification.
-
Product
Matrix Code Verification Systems
REA VeriCube
-
The REA VeriCube is a state-of-the-art matrix and barcode verification device which can be used across all industry sectors. Whether lying, standing or from top to bottom, virtually any test sample can be measured contact-free in the optimum measuring position. The measurement of optical codes in compliance with defined angles, distances and lighting allows accurate and reproducible measurement results and quality evaluations.
-
-
Product
QuartzXM Carrier Design Package
Model 4801
-
- Pin definitions and electrical specifications of all signals on the module- 3D models of the module- Thermal profiles of the module and components- Carrier reference design schematics- PCB stack-up recommendations- PCB design guidelines and routing rules- Operating systems and bootstrap guidelines- Additional electrical and mechanical engineering guidance
-
Product
Filter Design Software
QuickFil
-
QuickFil is a software for designing passive electronic filters. The result is an optimized circuit of inductors (L)and capacitors
-
Product
PathWave RFIC Design (GoldenGate)
-
Early in the RFIC design phase, monitoring system IC specifications such as EVM via RF simulation is a must. Simulations include effects of layout parasitics, complex modulated signals, and digital control circuitry. With PathWave RFIC Design, you can simulate in both the frequency and time domain and bring your designs to and from Cadence Virtuoso and Synopsys Custom Compiler.
