Diagnostics
Test routines run to determine errors.
-
Product
Resistivity Meter for Concrete
Ohmcorr Test System™
-
OhmCorr has two probes spaced 1.97" (5cm) apart which are placed in holes drilled to a depth of 3/8th" (8mm) and filled with conductive gel. The direct digital read-out of resistivity is displayed on the LCD when the control switch is activated. OhmCorr and CorMap, when used together, provide an economical and sound diagnostic system of corrosion in reinforced concrete.
-
Product
CMOS USB3 Cameras
CELERA One Series
-
CELERA One camera series provide the same excellence in quality, flexibility and performances of CELERA cameras, with the only exception of a single USB3 interface, while keeping the original extremely reduced dimensions and rugged design that make CELERA One cameras suitable for most applications: automated optical inspection, high performance sorting systems, industrial metrology, microscopy, medical diagnostics and machine vision.
-
Product
Testing and Diagnostic Software Tool
SCSItoolbox Suite
-
The SCSItoolbox is the industry's most advanced and widely used testing and diagnostic software tool. In use world wide since 1992, the SCSItoolbox Suite encompasses every testing software tool that you need to test, troubleshoot, configure, and diagnose any single-ended, differential, SCSI 1, 2, 3, wide or narrow devices, Ultra II, Ultra3, FC, iSCSI, SATA, ATAPI, or SAS device!?
-
Product
SWaP Optimized Processing and Multifunction I/O & Communications System
NIU3A
-
The NIU3A is a small, rugged, low-power, self-contained processing and multifunction I/O system preconfigured with 24-CH programmable Discrete I/O, 8-CH ARINC 429/575, 4-CH CANBus and 2-CH MIL-STD-1553 functions. The NIU3A can also be configured with up to three smart Configurable Open Systems Architecture™ (COSA®) function modules. The NIU3A boasts Dual or Quad Core ARM Cortex®-A53 processors for customer software applications and I/O and communications management. The NIU3A is configured with two 10/100/1000BASE-T (GbE) Ethernet ports and an RS-232 port for maintenance / diagnostic or configuration interface. Ideally suited for rugged Mil-Aero applications, the NIU3A delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
-
Product
Machine Capability
NC-Checker
-
Metrology Software Products Ltd
We fine-tune your machine tools with automated diagnostics and precise calibration. We leave you with our NC-Checker software so you can benchmark the accuracy of your machine to assess its ongoing capability.
-
Product
2-Channel 40KSPS Datalogging Oscilloscope / 2-Channel 5.5 Digit DMM CF Card
CFD200
-
The CFD200 is a new concept in test equipment that allows a PDA, laptop or tablet PC to be turned into a dual channel Digital MultiMeter with sophisticated analysis capabilities. SmartAnalysis software facilitates step-by-step fault investigation with instant display of results and an interactive diagnostic guide. With the CFD200 it is possible to integrate multiple measurement functions into a single hardware/software platform, providing high-level analysis features and a small, lightweight and portable unit. The CFD200 is an extended Compact Flash design offering two channels with full galvanic isolation to host and channel-to-channel. Each offers a scope function up to 40KSPS with full datalogging capability and 650V max. input voltage.
-
Product
Built-In Relay Self-Test Diagnostic Test Tool
BIRST
-
Verification and diagnosis of complex switching operation in a test system has always been an issue. BIRST (Built-In-Relay-Self-Test) diagnostic test tool provides a quick and simple way of finding relay failures available on some of our LXI and PXI switch matrices.
-
Product
pH 700 Benchtop pH Meter
-
The easy-to-use, microprocessor-based pH 700 benchtop meter measures pH, mV, relative mV, and temperature. The large, dual-display LCD provides excellent visibility—even from a distance. Automatic temperature compensation (ATC) maintains reading accuracy even with fluctuating temperatures. Five-point pH calibration, with automatic buffer recognition for both USA (pH 1.68, 4.01, 7.00, 10.01, 12.45) and NIST (pH 1.68, 4.01, 6.86, 9.18, 12.45) pH buffers, makes for easy calibration no matter which requirement you need to meet. Meter features HOLD, ATC, selectable °F or °C measurement, recall of electrode slopand offset, and electrode diagnostics. The convenient pull-out quick reference card keeps procedures handy at all times. Meter accepts any pH or ORP electrodes with a BNC connector.
-
Product
Test Program Sets (TPS)
-
Data Review, Corrections, & Generation (Reverse Engineering). Technical Requirement Documentation (TRD). Test Strategy Reports (TSR). Test Program Development – Software. TPS Sell-Off & Acceptance. Life-Cycle Support. Technical Interface Test Adaptors (ITA) – Hardware. Training - TPS Development, ATE/TPS Operator, Fault Diagnostic, ATE Maintenance.
-
Product
Network Analyser And Diagnostics
Module Analyser
-
Module Analyser is a 5 in 1 easy to use CAN bus analyser with the following advantages:■ CAN and LIN monitoring via DBC/LDF/Fibex files ■ Automotive OBD ISO15765 Scan tool and UDS ISO14229■ J1939■ Integrated ODX/MDX editor■ Data acquisition and logging
-
Product
On-Site Oil Analyzer
MiniLab 33
-
With three simple tests, the MiniLab 33 delivers on-site oil analysis, providing immediate actionable results, saving time and reducing costs. Highlights of this system include:*One product, delivering lab-quality analysis outside of the lab*Simplified workflow for the non-expert user, no chemist required *Simplified operation, data reporting and report interpretation via the TruVu 360 Diagnostic Sets with recommended actions
-
Product
Digital Pressure Gauges
SCJR1-KIT-EMA
-
Parker's ServiceJunior diagnostic test kits are ideal to digitally measure pressure and capture min and max fluctuations in any hydraulic or pneumatic system.
-
Product
Access Network Diagnostics
-
As fiber networks are built and services scale, Fiber Diagnostics helps Service Providers manage their customers’ experiences by ensuring successful installation and service start up, while decreasing time to revenue. Once the fiber network is in service, Enghouse Fiber Diagnostics assures customer satisfaction through improved customer service and rapid time to repair, while reducing operational costs.
-
Product
Nemo Handy Handheld Measurement Solution
-
Nemo Handy is an Android application that enables measuring wireless diagnostics information of air interface and mobile application quality-of-service (QoS) and quality-of-experience (QoE).
-
Product
Fast Ethernet SFP Module
SFP-FSS-20KRX
-
Industrial standard small form-factor pluggable (SFP) package, Provides digital diagnostics monitoring (DDM) functionality. Wide specifications and fiber types available, Comes with metal enclosure for EMI, The Class 1 laser product complies with EN 60825-1.
-
Product
Positive Train Control
PTC
-
Positive Train Control (PTC) Systems help in preventing accidents caused by train operators or dispatcher errors and characteristics include:- Train separation or collision avoidance- Line speed enforcement- Temporary speed restrictions- Rail worker wayside safety Providing the required radio coverage in railroad tunnels often presents a challenge especially for real-time applications like PTC. PBE offers a Positive Train Control Safety System (PTC) that provides 220 - MHz/LTE signals re-broadcast over radiating cable into the railroad tunnels.For longer coverage PBE customises solution based on the tunnel configuration/customer requirement. PBE positive train controls technology provides amplifiers to extend the coverage inside the tunnel. Remote monitoring and diagnostics is offered by PBE to view the status and health of the system. Providing this level of control not only increases safety but also provide significant maintenance reduction costs.
-
Product
Safe Series Connection
-
The safe series connection enables the connection of up to 32 safety sensors up to performance level e. You can wire safety switches and safety sensors with OSSD outputs in the mix, regardless of the manufacturer. Selected detailed diagnostic information is also available for each sensor or switch.
-
Product
Diagnostic Relay Buddy 12/24
192
-
Relay Buddy 12/24 is a quick go / no-go tester for the most common automotive relays. This new version Relay Buddy tests both 12 and 24 volt relays. If the relay fails the test, 3 different trouble codes will advise you of the possible causes for the failed relay. The red LED will flash once, twice or three times to indicate the problem. Trouble code definitions are printed on the back of the tester for your convenience.
-
Product
Diagnostics & Testing Equipment
-
Parker offers an array of diagnostic and test solutions for measuring hydraulic and pneumatic data and for troubleshooting operational problems. These include analog and digital flow and pressure meters and viscometers as well as associated devices such as sensors, vacuum and pressure controllers, quick couplings, and test point connectors.
-
Product
Software
-
SKF Condition Monitoring Center
SKF has comprehensive software solutions with powerful diagnostic and analytical capabilities to provide fast, efficient and reliable storage, analysis and retrieval of complex asset information. This software makes the information accessible throughout your organisation. The software available for your condition monitoring needs include the following.
-
Product
Ensure Accurate Screening, Diagnosis & Monitoring
Ultrasound QA Solutions
-
Gammex is the only ultrasound QA solutions manufacturer with expertise in medical physics since 1969.The 156 phantom helped establish the mammography repeatability and reproducibility standard: any mammography technologist (radiographer) at any time, on any machine, can provide the same image set to help detect breast cancer.We collaborated with clinical and academic thought leaders to develop our patented HE Gel and the first portable Doppler Flow phantoms in the world. HE (High Equivalency) Gel is what sets Gammex ultrasound products apart; it helps ensure all your transducers and system settings are fully tested across the entire frequency range from 2 to 18 MHz. Our HE Gel combined with our medical physics and quality control expertise gives you confidence with consistent diagnostic image quality in clinical applications.
-
Product
Portable PD Monitoring of Medium and High Voltage Power Equipment with UHF, AE, and HFCT
PDiagnosticM
-
Power Monitoring and Diagnostic Technology Ltd.
The PDiagnosticM is a portable system that utilizes UHF, AE, and HFCT sensor modules to monitor PD signals from Medium and High Voltage power equipment.The system is ideal for monitoring critical power assets to find and monitor intermittent PD signals and to analyze the developing PD trends. The PD type is determined by automatic pattern recognition and internal defects can be found at an early stage.The system provides advanced protection with alarm functions and our Deep Learning data analysis capabilities utilizing our proprietary Intelligent Cloud Diagnostic Technology.
-
Product
Liquid Flow Meters
-
Sensirion''s liquid flow sensors establish new standards wherever low liquid flow monitoring, liquid handling and liquid dosing are important. Our unique CMOSens Technology allows to measure the liquid flow even through the wall of the flow channel (US Patent 6183944) in milliliters, microliters or even nanoliters per minute. Applications in fields like medical devices, diagnostics and process technology benefit daily from our solutions.
-
Product
Intelligent Power Monitor
iPM
-
NAI’s iPM is an Intelligent Power Monitor that provides a precise, instrument grade, digital analysis of input power lines. This advanced, DSP-based unit monitors single-phase, 3-phase 4-wire wye, or 3-phase Delta power lines at various input voltage levels and frequencies.The iPM is equipped with an EIA RS485-compatible serial communications interface that permits additional control functions and readout of diagnostic data, and features a Background Built-in-Test (BIT) that constantly monitors the health of unit hardware and software. This power monitor is designed and qualified to the most stringent performance and environmental requirements, and is ideally suited for rugged defense and industrial applications.
-
Product
ATE Self Test Fixtures
AL663
-
AL663 fixtures include all the electronic parts required to perform an effective test platform diagnostic. The AQ818 device allows to perform a series of tests, obtaining a report of the faulty instruments or switch modules and also a report about the relay contacts estimated life.
-
Product
Diagnostic Solution
SYSTEM 8 Diagnostic Solution
-
The SYSTEM 8 Diagnostic Solution is the solution to board fault-finding problems. Equally at home with analogue and digital PCBs, the systems 64 digital and 24 analogue test channels provide a variety of test and measurement techniques to track down the most elusive faults.
-
Product
DGN Advanced Reporting Feature, GTE 10.00p
K8223B
-
The Basic Diagnostics levels is the main troubleshooting tool used by all users to check the hardware configuration, and verify and isolate hardware failures. Some Diagnostic tests require that a Pin Verification Fixture be installed on the system.
-
Product
Carbon and Sulfur in Inorganic Materials by the Combustion Infrared Detection Technique
844 Series
-
LECO combined our customers' feedback with innovative engineering to develop the CS844, an elemental analyzer designed for wide-range measurement of carbon and sulfur content of primary steels, ores, finished metals, ceramics, and other inorganic materials using the combustion technique. Our exclusive MS Windows®-based software, coupled with a boom-mounted touch interface, gives you complete access to instrument control, analysis settings, diagnostics, reporting, and more—without sacrificing valuable bench space.
-
Product
DrivePro Remote Ultimate
-
Benefit from the ability to share live vehicle data, receive complete OEM repair information, wiring diagrams and more directly through the DrivePro Remote Unlimited diagnostic support platform.
-
Product
EZ-Tach Digital Automotive Tachometer
325
-
The EZ-Tach makes RPM measurements quick and easy. This is a very useful tool for tune-up and other diagnostic work where accurate RPM readings are required. Just clamp over any spark plug wire and get accurate RPM on conventional or DIS ignition systems. The unit also features a data hold function. The large 2000 count LCD display shows; RPM, function, data hold indication and low battery indication. The EZ-Tach is powered by one 9 volt battery. Battery and instructions are included.
