-
Product
P104 LVDT/RVDT Measurement Board
73LD4
-
NAI’s 73LD4 is a PC104-compliant LVDT/RVDT Measurement Board with six separate transformer-isolated channels. The channels can incorporate up to six programmable LVDT/RVDT-to-Digital Tracking Converters in a stack-through module. Each channel is programmable for 2-, 3-, or 4-wire inputs that automatically range between 2.0 volts and 28 volts, so there is no need to purchase multiple boards set for specific inputs. Operating frequency between 360 Hz and 10 kHz can be specified. Each channel also produces differential incremental encoder (A & B) outputs with programmable resolution and a zero-degree marker pulse.
-
Product
Handheld Digital Multimeter, 4.5 digit, up to 800 hours battery life
U1282A
Digital Multimeter
60,000 counts resolution on dual display0.025% basic DC voltage accuracy Longer battery life up to 800 hours Certified to IP 67 for dust and water protection Tested to withstand a 3-meter (10-ft) drop Programmable via USB (Download Programming Guide here)CAT III 1000 V/ CAT IV 600 V overvoltage protection Vsense for non-contact voltage detection Square wave output for generating pulse width modulation (PWM) signal Frequency counter Low pass filter
-
Product
SY024 Pulse Rate to Current or Voltage Converter
-
SY024 PR* is a Pulse Rate-Analog converter designed to accept a frequency and produce a proportional Current or Voltage output. The current output can be 0-20mA or 4-20mA and the voltage output version is user adjustable from 0-5V to 0-10V.
-
Product
Fluxmeter
Model 2130
-
The Model 2130 Fluxmeter is a fully featured, high-end Fluxmeter based measurement system. It is a compact instrument with high accuracy, automatic drift correction, microprocessor control, and twelve measurement ranges to allow the operator to configure the meter for maximum resolution and accuracy. The Model 2130 is capable of measuring (DC), alternating (AC), or pulsed magnetic fields. Selecting primary measurement functions is quick and easy with dedicated front panel function keys. An easy to use menu allows access to user defined parameters such as upper and lower magnetic limits and relative magnetic measurements.
-
Product
High Current / High Voltage Pulsers
DEI Division
-
Berkeley Nucleonics Corporation
is optimized for high impedance capacitive loads, driving extraction grids and deflection plates, and pulsing or gating power tube grids. It generates an output voltage of 6,000 volts with rise and fall times less than 60ns, with very flat voltage pulses from 160 nanoseconds to DC into a capacitive load.
-
Product
Function/Arbitrary Waveform Generators
SDG2000X Series
-
SIGLENT’s SDG2000X is a series of dual-channel function/arbitrary waveform generators with specifications of up to 120MHz maximum bandwidth, 1.2GSa/s sampling rate and 16-bit vertical resolution. The proprietary TrueArb & EasyPulse techniques help to solve the weaknesses inherent in traditional DDS generators when generating arbitrary, square and pulse waveforms. With advantages above, SDG2000X can provide users with a variety of high fidelity and low jitter signals, which can meet the growing requirements of complex and extensive applications.
-
Product
Reference Radiators / Comb Generators
-
The Spectrum Generator is a family member of the Schwarzbeck pulse generators, which are used as pulsestandard world wide. Whilst the latter one uses a bounce free relay contact to discharge a coaxial lineto the load resistor, it uses a special avalanche transistor instead of the relay contact.
-
Product
Three Phase High Precision Reference Standard Energy Meter
SY3102
-
Hong Kong Songyang Industrial Ltd.
There are three ports for pulses to output. And its constants can be set automatically or manually. Types of constants can be set also: active power, reactive power, apparent power, voltage, and current.
-
Product
Power Probes
RkT Thermopile Series
-
The RkT Series thermopile power probes are ideal for measuring Nd:YAG, CO2, and other mid-power lasers. The probes are designed to withstand average power densities up to 20kW/cm2 (15MW/cm2 peak pulse power density). The flat UV to far-IR spectral response allows the probes to measure broadband sources as well. Measure the power of cw sources or the average power of sources pulsed at 5Hz or greater.
-
Product
High-Performance Autoranging DC Power Module, 50V, 10A, 100W
N6752A
Power Module
The Keysight N6752A is a 100 W high-performance, autoranging DC power module that provides low noise, high accuracy and programming speeds that are up to 10 to 50 times faster than other programmable power supplies. Optional high-speed test extension offers an oscilloscope-like digitizer that increases measurement accuracy when viewing high-speed transient or pulse events within the device-under-test (DUT).
-
Product
Surge/wave Simulators
-
Suzhou 3ctest Electronic Co.,Ltd.
Surge pulses occur due to direct or indirect lighting strokes to an external circuit. This leads to current or electromagnetic fields causing high voltage or current transients. Another source for surge pulsed is switching transients originating from switching disturbances and system faults.
-
Product
State, Event & Pulse Data Loggers
-
These data loggers can record rates from pulse output transducers, on/off or open close state changes or events.
-
Product
High Voltage Measurement
-
High Voltage Pulse Attenuator is used to attenuate high voltage pulse signals in a 50 system. It is consist of highly surge robust components with great voltage linearity. The device is symmetrical, Input and output can be exchanged.
-
Product
Milliohm Meter
16502
-
Chroma Systems Solutions, Inc.
Basic accuracy : 0.05%Pulsed test current output mode is used to reduce thermal EMFs affection on milliohm measurementDC test current output mode is used to fasten measurement speed for inductive DUTDry-circuit test current output mode (limited Max. 20mV) is used to measure such contact resistances where the maximum open-circuit voltage must be limited to 50mVTemperature correction (TC function) regardless of material or temperatureUseful temperature conversion function for motor/ coil evaluation4 channels R scan with balance check function for fan motor (combined with A165017 option)0.001mΩ~1.9999MΩ wide measurement range with 4½ digits resolutionStandard RS-232 interfaceOptional GPIB & Handler interfaceBin-sorting functionComparator and pass/fail alarming beeper functionLarge LCD display (240 x 64 dot-matrix)Friendly user interface
-
Product
Xenon Light Sources
-
Our pulsed Xenon light source is used in applications where a long lifetime and high output power is needed, such as in fluorescence measurements. This is an affordable UV source, but the spectral output is not as smooth and continuous as the AvaLight Halogen and Deuterium light sources.
-
Product
Demonstration Board
SAMPULSE20x2
-
The SAMPULSE20x2 is a demonstration board for the Furaxa SiGe3 30GHz sampler/pulser IC. The SIGe3 IC is a dual channel sampler pulser chip, and the SAMPULSE20x2 demonstration board contains two 2.4mm combined TDR input/output connectors, one to each sampler/pulser channel in the IC. The SiGe3 IC's two sampler outputs are then sent to to two SMA jacks, the first outputting the sample taken on the rising edge of the sampler clock, and the second containing the sample taken on the falling edge of the sampler clock. The sampler clock input, which must be a square wave, may be set to any frequency from 5MHz to 1GHz, causing the board take two pairs of samples (one on each clock edge) at rates from 5 million to 1 billion per second. A pulser clock input, which may be set to any frequency from 5MHz to 2GHz, and MUST be a square wave (preferably differential) with rise time under 100pS, causes the board to produce concurrent pulses on both of the SiGe3's I/O pins, which produce near-concurrent pulses at the two 2.4mm sampler/pulser TDR input/output connectors.
-
Product
Isolated Gate Drivers
-
Analog Devices’ isolated gate driver portfolio offers designers performance and reliability advantages over designs utilizing optocouplers or pulse transformers. Utilizing ADI’s proven iCoupler® technology, the isolated gate driver family offers the advantage of a maximum propagation delay of 50 ns, less than 5 ns channel-to-channel matching, a 50-year lifetime for 400 V rms working voltage and galvanic isolation in a single package.
-
Product
VFTLP+ Test System
4012
-
The Model 4012 VFTLP+™ test system was developed in early 2000 to add high speed measurements to the usual I-V plot, to measure and record the real TDDB waveform which causes oxide failure.*Accurate measurements of this waveform have finally been identified by Barth Electronics Inc. and CDM protection can now be based on known dimensional design parameters. We identify the response of your CDM protection circuits with 100ps risetime pulses which simulate the real CDM test. This is the only way with which to provide the total gate oxide threat voltage data.*Convenient, precise, repeatable operation*Computer controlled for automated testing
-
Product
Torque Testers
-
Torque testers are ideal for a variety of applications in light assembly and can be used to test hand tools, power tools and even pulse tools.
-
Product
Photo Optic Sensors
-
From patient monitoring in hospitals, to wearables and home healthcare applications, TE Connectivity (TE) offers photo optic sensors and components for non-invasively measuring blood oxygenation (SpO₂) level. With more than 27 years of proven reliability and expertise, TE has designed SpO2 sensors with best-in-class flexibility to accommodate multiple wavelength options. Our ability to provide both components and complete sensor packages make us the leading choice for pulse oximetry applications that require high degrees of precision, durability and performance.
-
Product
P-Series Dual Channel Power Meter
N1912A
Power Meter
30 MHz video bandwidth Single shot real time capture at 100 M sample/s per second Key Measurements: - peak, average, peak-to-average ratio, rise time, fall time and pulse width22 Predefined formats: WiMAX, DME, HSDPA, etc. One screen view for pulse measurement analysis: Auto Scale, Auto Gate, Rise/Fall Time, Duty Cycle, etc. Internal Zeroing and Calibration while connecting to the DUT Bench Vue software enabled
-
Product
Optical Time Domain Reflectometers
-
An optical time domain reflectometer (OTDR) is a precision instrument used to locate events or faults along a fiber link, typically within an optical communications network. The OTDR launches a series of high speed optical pulses into the fiber to be measured. Various events on the fiber generates a Rayleigh back scatter that returns to the OTDR and the strength of the return pulses are measured and integrated as a function of time, and plotted as a function of fiber length. The horizontal axis is the distance and the vertical axis is the loss.
-
Product
Programmable DC Electronic Load
-
Four parameters, highlight VFD display.Resolution of voltage and current: 0.1mV/0.1mA.Four working modes: CV/CC/CR/CP.Three dynamic test function (up to 10KHz): continuous load switching mode, pulse load mode, toggle load switching mode.Ten groups automatic testing data files with each file 10 steps.Intelligent fan cooling, coding switch, built-in buzzer, non-slip feet .Complex current sequence list test mode .Remote sensing function.Battery discharging test mode.All modes turn on default
-
Product
FiberPulse OTDR
XO1
-
FiberPulse OTDRs send pulses down fiber optic networks from one end of the fiber, displaying a trace and reporting all detected events such as splices, connectors, macrobends and fiber ends and breaks. The total fiber length is reported along with name, location, loss and reflectance of detected events. The intuitive keypad design features integrated shortcut keys designed for quickly positioning and analysing events. Another feature of this unit is the Live Optical Signal Detect Function, which tests if the fiber is live before sending the pulse, this can effectively prevent accidental damage to the OTDR and attached communication equipment.
-
Product
Data Diver
MT-8006B
-
LCD display for dialing number, Caller ID, Clock and other informationIndicator for determining the Line service and speedHigh impedance monitor for data safe operation without disrupting existing traffic.Smart power saving enables battery life up to 6 months12 phone number memory for speed dialing16 dialing number memoriesTone (DTMF) and pulse operationUp to 32 digits phone number memory for speed dialing keyPre-dialing and last number redial functionPBX pause key, insert a PBX pause in stored numbersTelephone line polarity indicatorsLow battery indicationBacklight functionRJ-11 port for easy test leads changeRinger and voltage LED indicationAngled bed of nails and RJ-11 plug
-
Product
Advanced Seismic Source
GI-SOURCE
-
Sercel developed the GI-SOURCE to reduce and suppress the bubble oscillation from a single impulsive source to simplify processing. The GI-SOURCE impulsive source is based on the same technology as the GI-SOURCE but is different in that it has two independent air chambers within the same casing : the Generator (generating the primary pulse and creating the main bubble) and the Injector (injecting air inside the main bubble so that it collapses quickly).
-
Product
Clock Synchronization
-
Analog Devices Clock synchronizers are designed for wired networking applications, providing the clock redundancy functionality needed to maximize system uptime. Our technology supports clock synchronization with common standards, including 1 pulse per second (PPS) output signal from a GPS receiver. GPS signals are broadly available and utilize an extremely stable atomic clock as its time base, but they are often noisy. Systems rely on the IEEE1588 timing protocol to establish synchronous communications across the wired network, including synchronous Ethernet and synchronous digital hierarchy (SDH) to optical transport network (OTN) mapping/demapping. The IEEE1588 protocol has emerged as the preferred method for Clock synchronizing systems throughout both computer networks and local area networks (LAN).
-
Product
Frequency Counters
-
Handheld and bench-top frequency counters up to 6GHz Universal counters with VLF capability and pulse measurement and totalizing in addition to frequency/period.
-
Product
Digital Input Board
VME-1182A
Digital Input Board
A multifunctional intelligent controller allows COS, SOE, pulse accumulation, debounce times and time tagging control on a per-channel basis.
-
Product
Test Data
-
Studies by major universities were conducted in response to a request from the military, scientific and engineering communities for scientific validation of claims that Pulse Technology actually improves battery efficiency and lengthens battery life. PulseTech contracted with Oakland University in Rochester, Michigan and Ohio State University in Columbus, Ohio to conduct separate evaluations of the technology. These extensive evaluations began in the summer of 1998 and concluded in the fall of 2000.
