-
Product
PXI-8431, 4-Port, RS485/RS422 PXI Serial Interface Module
778985-01
Serial Interface
4-Port, RS485/RS422 PXI Serial Interface Module - The PXI‑8431/4 is a high-performance interface for high-speed communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full- and half-duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
Mass Flow Controller for Medium Flow
HFM-201 / HFC-203
-
The HFM-201/HFC-203, Teledyne Hastings' flexible, general purpose series of mass flow meters and controllers accurately measure and control mass flow in a variety of applications. Featuring reliability and stability, the 200 Series is chosen for its very stable performance with varying ambient conditions. A wide choice of elastomer seals make this flow controller compatible with most gases.The HFM-201 / HFC-203 meters and controllers have flow ranges from 0-25 slm to flows of 0-1000 slm; provide analog outputs, are constructed of stainless steel and can be configured with normally open or normally closed valves. The full scale range is specified by the end user. A NIST traceable calibration certificate is standard. Many corrosive gases and pressures up to 1000 psig are easily measured. Cleaning for oxygen service is available.
-
Product
IP Surveillance Camera
ENVIROMUX-IPCAM
-
View and control the camera from the ENVIROMUX web interface, the camera web interface, included software, or with a compatible cell phone. With the ENVIROMUX-2D/5D/16D, a triggered snapshot can be forwarded in alert e-mails. A snapshot can be triggered by any programmed event (motion detection, door open/close, glass break, smoke, liquid detection, etc.). Image sensor: 1/4" progressive scan CMOS sensor. Video Streaming: simultaneous Motion JPEG and MPEG-4. Frame rate: 30fps at 640x480 (VGA) resolution. Lens: F2.0, 4.0 mm (0.16 in). RJ45 connector. Wireless models: wireless IEEE 802.11 b/g up to 54 Mbps. Regulatory approvals: CE, FCC, RoHS.
-
Product
Radius Radiation Probe
Hawk Radius®
-
The Hawk® Radius is a ruggedized solution for monitoring both ambient and elevated levels of ionizing radiation. Like a Hawk with its remarkable vision, the Hawk Radius Probe “sees” things that other probes cannot. The high sensitivity weatherized pancake sensor can provide early warning of changing ambient radiation conditions, while the energy compensated detector can accurately report penetrating gamma radiation dose rate at elevated levels. Radius probes are typically deployed as part of an environmental radiation monitoring program, or for safety and security systems. In its standard configuration the probe detects beta, low energy gamma and x-radiation with one channel and energy compensated penetrating gamma radiation levels with a second channel. It can be configured to detect alpha radiation as well. The Hawk® Radius has been deployed worldwide in demanding conditions for protecting communities and collecting environmental radiation data. It can be deployed easily and requires minimum maintenance. The Radius is compatible with Medcomʻs GeigerLink adapter and the IMI Gateway App for use with personal computers. It can also be used with most data loggers including popular Campbell Scientific models.
-
Product
GPIB-RS485/RS422 GPIB Instrument Control Device - Taiwan 110VAC
779733-11
GPIB Controller
The GPIB‑RS485 is an IEEE 488 controller device for PCs with RS485 or RS422 ports. You can use this device to integrate an instrument into your system using GPIB. This device transforms a computer with an RS485 or RS422 serial port into a talker, listener, or controller on the GPIB bus. It can also interface RS485 and RS422 instruments and peripherals to the GPIB bus. It can implement the physical and electrical specifications of the IEEE 488, RS485, and RS422 standards, as well as interpret and execute high-level commands from the serial port, including serial‑to‑GPIB, and GPIB‑to‑serial protocol conversions. This device is IEEE 488.2 compatible. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
Product
Automatic Fixture Removal
S95007B
-
Many devices do not have coaxial connectors and so they are put in fixtures in order to measure them in a coaxial environment. You must accurately remove the effects of the fixture to get a good measurement of the device under test (DUT). This option adds a powerful application wizard to guide you through characterizing a fixture and removing it from the measurement. The S95007B software is compatible with M980xA PXI Vector Network Analyzers.
-
Product
2U Wall-Mount/Tower Embedded Mini-ITX Chassis With One Dual Expansion Slot
RK-200I
Chassis
- Supports one dual slot expansion card(Low Profile)- Reserved for 2 USB, 2 COM, and 2 antenna punchouts.- One 3.5” drive bay and one 2.5’’ drive bay. (Compatible for three 2.5’’ drive bays)- 8cm two ball bearing PWM fan ( 42.5 CFM)- Support both Flex ATX power supply & AC-DC power adaptor
-
Product
Night Vision Lighting
-
Astronics has the capability to design and manufacture complete lighting systems for the entire aircraft to ensure NVIS compatibility. They can provide products to retrofit existing aircraft or assist in the design of products for new build aircraft.
-
Product
Digital Magnetic Compass
TargetPoint SX
-
For laser rangefinder and targeting systems designers using the Vectronix® DMC-SX, the TargetPoint-SX is form, fit and function compatible to the Vextronix part, requiring little or no work to design into existing systems. And it’s much less expensive.
-
Product
4x4 VGA + Audio Matrix Switch with UTP Output and IP Control
VSM-I-A-4-JA4
-
Switch up to 4 VGA inputs to 4 VGA outputs with independent audio routing. Additional RJ45 output connectors provide extended output up to 1000 ft (305 m) over a single UTP cable (with compatible URA receivers). 550 MHz bandwidth supports resolutions beyond 1920x1200.
-
Product
48-Ch Digital I/O USB Module
USB-4751
-
Compatible with USB 1.1/2.0Bus-powered48 TTL digital I/O linesEmulates mode 0 of 8255 PPIBuffered circuits for higher driving capacity than 8255Interrupt handling capabilityTimer/Counter interrupt capabilitySupports both dry and wet contact50-pin Opto-22 compatible box headerPortableSuitable for DIN-rail mountingOne lockable USB cable for secure connection included
-
Product
Power Cable For GPU Card - Two B4P
1700024754-01
PCIe Cable
Output：6+2-pin PCIe power conn.Input：4 pin Molex power conn.Lenth：10 cm (3.94")Compatible Devices：PSU
-
Product
NI-9226, 8-Channel, 400 S/s Aggregate, 0 Ω to 4000 Ω, PT1000 RTD C Series Temperature Input Module
783864-01
Temperature Input Module
8-Channel, 400 S/s Aggregate, 0 Ω to 4000 Ω, PT1000 RTD C Series Temperature Input Module - The NI‑9226 is a resistance temperature detector (RTD) input module. You can configure the NI‑9226 for two sample rate modes: high sample rate or high resolution. The NI‑9226 is compatible with 3‑ and 4‑wire RTD measurements, and it automatically detects the type of RTD (3‑ or 4‑wire) connected to the channel and configures each channel for the appropriate mode. The module provides per-channel current excitation. The NI‑9226 features calibration and includes a channel‑to‑earth ground double isolation barrier for safety, noise immunity, and a high common-mode voltage range.
-
Product
Additional Products: 200 Pin D Cables - 200 Pin to 200-Pin
-
The connector to connector cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
PCI 4-Input Frame Grabber
611
-
Color or monochrome: PAL, SECAM, NTSC, RS-170 compatible 4 composite video inputs or 3 composite and one S-video 8 TTL I/O lines for camera control Programmable AGC, hue, contrast, saturation Optional enhanced SDK for Windows 98/2000/NT/XP/CE Optional Linux and QNX drivers
-
Product
Flash SATA DOM
FSD Series
-
Axiomteks FSD (Flash SATA DOM) series is designed into Serial ATA II protocol type with compatible Serial ATA standard interface based on flash memory technology. This flash module is offered with various capacities ranging from 128 MB up to 32 GB and can operate under industrial temperature range goes from -40°C ~ 85°C in the harsh operating environments. The features of reliability, high performance, cost-effective and easy-tointegrate designs make FSD series a perfect solution over traditional storage devices.
-
Product
DMX to Analog Interfaces
-
The MTX-DE48 decodes signals from DMX control desks to analog dimmers. It is used to integrate DMX controllers into existing analog installations. The standard 0 to 10V output is compatable with many LED drivers. Output may be adjusted up to 28V for use with some older dimmer systems. A negative output voltage option is also available.
-
Product
Digital I/O Board, 32 Isolated I/O Channels, 24V
APCIE-1500
-
The PCI-Express 32 digital I/O board APCIe-1500 has 32 digital inputs/outputs (24 V or 12 V), 14 inputs are interruptible. The 16 digital power outputs are equipped with protection diodes and filters. The board is fully compatible to the PCI board APCI-1500. It is especially suited for applications like industrial I/O control, signal switching, ON/OFF monitoring of motors, lights etc. in the harsh industrial environment. The APCIe-1500 has interruptible inputs. They supersede continuous cyclical query processes (polling) for routine monitoring and evaluation tasks. This takes load off the processor and the software. At a change of state of the digital inputs the APCIe-1500 generates an interrupt, so that the system reacts on the event through the interrupt routine and herewith fulfils real-time criteria.
-
Product
PXIe 16 Bit Arbitrary Waveform Generator - up to 1.25 GS/s on 1 Channel
M4X.6630-X4
Arbitrary Waveform Generator
The M4x.66xx-x4 series arbitrary waveform generators (AWG) deliver the highest performance in both speed and resolution. The series includes PXI Express (PXIe) cards with either one, two or four synchronous channels. The large onboard memory can be segmented to replay different waveform sequences. The AWG features a PCI Express x4 Gen 2 interface that offers outstanding data streaming performance. The interface and Spectrum’s optimized drivers enable data transfer rates in excess of 2.8 GB/s so that signals can continuously replayed at a high output rate. While the cards have been designed using the latest technology they are still software compatible with the drivers from earlier Spectrum waveform generators. So, existing customers can use the same software they developed for a 10 year old 20 MS/s AWG card and for an M4x series 625 MS/s AWG.
-
Product
Vibration Combined Test Chamber
-
Vibration and Temperature & Humidity & Vibration Combined Test Chamber offer combined temperature, humidity, and/or vibration environments. Weiber models are designed for compatibility with user’s choice of electrodynamic or mechanical vibration systems. While each model is manufactured to standard designs, they may also be custom engineered to meet a wide range of stringent test requirements. The Test Chamber comes with optional capability to interface with vibration systems in both the horizontal and vertical modes of operation with rear or vertical sliding doors. The Weiber Series temperature/humidity and vibration chambers are designed to integrate with vibration systems in only the vertical mode of operation.
-
Product
4-Channel 200 MHz A/D with DDC, Virtex-7 FPGA - 3U VPX
Model 52761
-
- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Four 200 MHz 16-bit A/Ds- Four multiband DDCs- Multiboard programmable beamformer- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x4- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- 3U VPX form factor provides a compact, rugged platform- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
GPIB Cable, 0.5 Meter
10833D
GPIB Cable
The Keysight 10833D (0.5 meter) GPIB cable is engineered for exceptional reliability and durability even under the harshest conditions. When you buy Keysight GPIB cables, you can be sure of automatic, seamless compatibility between computers and instruments throughout your system. GPIB interface cables, cards, and software for your computers make it easy for you to access and control instruments and exchange data - and it all starts with the cables to connect your computer and instrument. Keysight GPIB cables are fully compatible with the IEEE 44.1 mechanical specification.
-
Product
PTI/PMAC/USB Sensor System Examples
-
*System for any strain gage based sensor*Compatible with every sensor is this catalog*Process monitoring*Process control*Portable datalogging*Portable, compact, and lightweight
-
Product
A Complex Representation of Human's Biology
CubiX Platform
-
The only microenvironment controller fully compatible with live imaging. It enables mimicking physiological and pathological culture conditions in vitro. Scalable, highly customisable and user-friendly.
-
Product
Gigabit Ethernet
SFP Transceivers - Copper
-
Copper SFP transceiver modules (1000Base-T) are 100% compatible with Cisco equipment, include RJ-45 connector, and compliant with applicable industry standards.
-
Product
Terminal Block and SCSI-II 68 Pin Connector with 2 Meter Cable
U2902A
Terminal Block
The Keysight U2902A is an accessory compatible and recommended to be used with the U2300A Series USB Modular Multifunction Data Acquisition and U2500A Series USB Modular Simultaneous Sampling Multifunction Data Acquisition. The pin-outs of the U2902A is dependent on the USB Data acquisition unit that it is working with. For more information, please refer to the data sheet or the user guide of the USB Data Acquisition unit that U2902A is to be used with.
-
Product
12 Block Desktop Receiver
VGR12
Receiver
VG Mass Interconnect products provide a common Universal interface for your custom test rack and simplifies functional test across your product line. Mass interconnect bench-top and rack mount receiver Plug and play interface blocks for signal, coax, high current, pneumatic controls, and more Stable proven products with 25 years in service Best cost of ownership Fast delivery next day on key products! Compatible to currently available test instrumentation and platformsThere are a number of different block types: Coax up to 26 GHz Power up to 150 Amps Coax and power combined Signal: up to 170 pins, @250 VAC/5 Amps Pneumatic: up to 13 fittings Vacuum: port modules High speed: USB 3.0, HDMI, RJ45
-
Product
PCMCIA Card
DAS-429PCMCIA/RT10
-
Both cards contain 68 Kbytes of true dual-port RAM, for data blocks, control registers and Look-up table, mapped within the Common Memory space. The card also contains a FLASH-based Card Information Structure (CIS) within the Attribute Memory space.The cards comply with the Personal Computer Memory Card International Association (PCMCIA Release 2.1) standard, including Plug and Play. The card's small size and suitability for PCMCIA compatible notebook computers with Type II and Type III slots make it a complete solution for developing and testing ARINC-429 interfaces and for performing system simulation of the ARINC-429 bus, both in the lab and in the field.The cards are supplied with C drivers, including source code, Mystic Windows software and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application.
-
Product
E-Series Average Power Sensor
E9300B
Power Sensor
Measure the average power of all modulation formats Wide dynamic range power measurements from -30 dBm to +44 dBm Frequency range 10 MHz to 18 GHzLow SWR for reducing mismatch uncertainty Calibration factors, linearity and temperature compensation data stored in EEPROM Compatible with EPM (new N1913A/ 14A, E4418B/ 19B), EPM-P (E4416A/ 17A) and P-series (N1911A/ 12A) power meters
-
Product
MAX31855 K-Type Thermocouple Sensor Breakout
SEN-30001-K
-
Breakout board for the MAX31855K digital thermocouple interface IC. Measured temperature range is -270C-1372C with known thermal characteristics and output resolution of 0.25C. This sensor supports a larger operating range (specifically in the negative range) than its predecessors, the MAX6674 and MAX6675, though it is not pin-pin compatible. This board is interfaced with a 0.1" 1x5 pin header, has a vertical mini thermocouple connector and four mounting holes for standoffs and 4-40 screws.
