-
Product
High Accuracy Spectrophotocolorimeter
LMS-3000
-
• Measure and display the relative spectral power distribution (UV-VIS-NIR) P(λ), chromaticity coordinate, correlated color temperature, rending index, color difference, peak wavelength, luminous flux, luminous flux efficiency and photometry parameters of light source and light material under the control of general PC. • Automatically adjust high-voltage, it not only shortens the measurement time, but also reduces the wear and tear of the instrument • Simultaneously measure the temperature in both environment and integrating sphere to make the data more visually and reliably • Figure of chroma and color difference in test report can be exchanged freely • Color display and print. The relative spectral power distribution (UV-VIS-NIR) P(λ), reports both in English. RS-232-C interface, compatible with all kinds of computer • LSP-500 AC Power source PC RS-232-C interface. compatible with all kinds of computer • Range of wavelength: 380nm～780nm(Special:200nm～780nm) • Accuracy of wavelength: ±0.2nm • Repeatability of wavelength: ±0.1nm • Accuracy of chromaticity coordinate: ±0.0003(under standard illuminate A) • Spectrum sample interval: 5nm(Special order:1nm) • Luminosity linearity: 0.3% • Accuracy of luminosity: 1 class • Correlated color temperature measure range: 1500K～25000K • Accuracy of CCT: ±0.3%(under standard illuminate A) • Accuracy of rending index: ±(0.3%rd±0.3) • Environment temperature measure range: -10℃～80℃ • Temperature measure range(In sphere): -10℃～100℃
-
Product
Transportable Gas Analyzer
CGT-7100
-
The CGT-7100 analyzer measures the concentration of gases in a continuous way, using a ratio photometric non-dispersive infrared absorption (NDIR) method. All pretreatment parts required for measurement, such as the pump, filter, and electric dehumidifier, are built-in. The analyzer can measure three components including CO, CO2, or CH4 (any two of these) and O2, and is compatible with measurement at 100 vol%. The CGT-7100 has wireless communication capability, so measurement values and charts can be displayed on PCs or smart devices. And measurement data can be exported using a USB flash drive.
-
Product
2-Ch 500 MHz A/D w/ DDC & 2-Ch 800 MHz D/A w/ DUC, Virtex-6 FPGA - 3U VPX
Model 52651
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Two 500 MHz 12-bit A/Ds- Two multiband DDCs (digital downconverters)- Two 800 MHz 16-bit D/As- One DUC (digital upconverter)- Multiboard programmable beamformer- Up to 2 GB of DDR3 SDRAM or 16 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- 3U VPX form factor provides a compact, rugged platform- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
1U Type Power Supply; ATX 300 W
PS300-1U
-
*Input Range: 90 ~ 264Vac Full Range8Output Voltage:**+5V, 14A**+3.3V, 12A**+12V, 25A (0.1A min)**-12V, 0.3A**+5Vsb, 3A*MTBF(hours): At 25°C, 100,000h*Safety: TUV, CSA22.2 NO.60950-1, IEC, UL, CE*Dimensions: 150 x 81.5 x 40.5 mm*Compatible with Axiomtek products: AX61120TB/AX61131TM/AX61133TM
-
Product
Fourier Transform Optical Spectrum Analyzer, 350 - 1100 nm
OSA201C
-
Thorlabs' Optical Spectrum Analyzers (OSAs) perform highly accurate spectral measurements. Compatible with fiber-coupled and free-space light sources, these compact benchtop instruments suit a wide variety of applications, such as analyzing the spectrum of a telecom signal, resolving the Fabry-Perot modes of a gain chip, and identifying gas absorption lines. Many commonly available OSAs use grating-based monochromators, which have slow acquisition times due to the need to mechanically scan the grating and average out noise at each wavelength. Thorlabs' OSAs acquire the spectrum via a Fourier transform using a scanning Michelson interferometer in a push/pull configuration. This approach dramatically improves the acquisition time, enables a high-precision wavelength meter mode with 7 significant figures and ±1 part-per-million accuracy, and allows the included software to provide robust statistical analysis of the acquired spectra, as explained in the Design tab.
-
Product
FPGA PXI Digital I/O Card
GX3500
Digital I/O
The GX3500 is a user configurable 3U FPGA PXI card which offers 160 digital I/O signals for specific application needs, as well as providing pin for pin compatibility with NI PXI 7811R and 7813R FPGA cards. The card employs the Altera Cyclone III FPGA which can support clock rates up to 150 MHz and features over 55,000 logic elements and 2.34 Mb of memory.
-
Product
Mobile Application Testing
-
Mobile compatibility testing covers aspects of platform fragmentation, physical characteristics, and the App Store review guidelines.
-
Product
Flex Clamp Meters
-
Flex Clamp Current Probes expand existing meters. Compatible with most meters using universal banana leads. Flexible Coil adds accessibility - easily maneuvering around cables that are in hard to reach areas and large enough to thread around larger conductors.
-
Product
Signal Generator Extension Modules
SGX
-
Virginia Diodes, Inc. (VDI) Signal Generator Extension (SGX) modules provide high performance frequency extension of microwave signal generators into the THz range. VDI SGX modules offer full waveguide band coverage and are available from WR15 (50 to 75 GHz) to WR1.0 (750 to 1100 GHz) with additional bands under development. This turn-key, sweepable solution is compatible with any microwave signal generator that meets the input frequency and power requirements.
-
Product
Low Profile PCI Express 8-Port
7803ec
-
The 7803ec low-profile PCI Express serial interface provides eight RS-232 serial ports. All modem control signals are implemented for maximum compatibility with a wide range of serial peripherals. Each serial port features an ultra high-speed UART, flexible clock prescalar, and large 256-byte Tx/Rx FIFOs allowing the adapter to support the widest range of standard and non-standard baud rates to 230.4 Kbps. These features make the 7803ec ideal for data-intensive applications that require reliable, fast throughput rates.
-
Product
InfiniiMode Active Differential Probe, 1.5 GHz
N2750A
Oscilloscope Probe
The N2750A InfiniiMode differential probe is a new generation of low-cost differential active probes compatible with Keysight InfiniiVision and Infiniium oscilloscopes’ AutoProbe interface. It comes with new operation modes and convenient measurements of differential, single-ended, and common mode signals with a single probe tip, without reconnecting the probe to change the connection. The N2750A probe’s InfiniiMode provides the following modes of operation.
-
Product
Conveyor Compatible & Conveyor Compatible
Automator Double Sided
-
Designed to provide factory assembly line conveyor based pneumatically actuated full test automation. Interchangeable pneumatics and manual lever options provide operation as a fully automated tester or as a manual bench top tester. These functional interchangeable options allow this fixture to grow with you as your production volumes increase. Test plate changeover is a quick 2 minute job. 4 thumbscrews to change the bottom plate and 4 SHC screws to change the top plate. The top plate drops down and slides out with the connector assembly. The bottom plate lifts up and out. The new plates slide back in. All rear panel connectors are mounted to the aluminum bracket on the top plate. This whole top plate assembly slides out together eliminating wiring hassles. Double sided access plate sets use transfer pins to get the signals from the bottom plate up to the top plate.
-
Product
Handheld Battery Powered Digital Synchro Meter
DSM-4
-
The DSM-4 is the handheld battery powered digital synchro meter with a large four digit LCD display. It is auto-ranging to accept virtually all standard military synchro signals. The DRM-4 is a handheld battery powered digital resolver meter. A dual range switch provides compatibility with all low-level resolvers ranging from 3.5V to 14V.
-
Product
Single Channel USB Programmable High-Pass Filter
USBPHP-S1
-
The USBPHP-S1 stand alone USB controllable module provides a single channel of high pass filtering and high-quality instrumentation amplifier for front-end signal conditioning compatible with all popular A/D converter devices. The USBPHP-S1 is powered with 9 to 12VDC so it can be connected to a battery voltage source or the supplied 115-220VAC adapter may be used for operation with wall power anywhere in the world. When programmed from the USB port, the USBPHP-S1 will remember all of the programmed properties between power cycles. Program once and operate as a stand- alone signal conditioner without having to reprogram for every use. This is perfect for turn-key applications. It's easy to connect the USBPHP-S1 into the data collection system. Input and output signals can be routed through BNC connection or using the detachable screw terminal connectors. Optional SMA type adapters are also available.
-
Product
Avionics Generator
MPG 4010 Series
-
The MPG 4010 Series is fully compatible to Aeroflex NAV 750C, 2030 and 2040 Series GPIB commands, enabling simplified and optimized replacement. Avionics parameters are presented in the same form as described in the ICAO standards. The 4010 Generator is the ideal solution for the testing of avionics on-board LRU and airfield alarm monitors in STTE systems. The use of a Vector Modulator and Digital Modulation Techniques ensures very high accuracy and stable performance over all operating conditions.
-
Product
MIL-STD-1553 IRIG 106 Chapter 10 Streaming Application
F-SIM-1553-CH10-STREAM
-
Avionics Interface Technologies
Streams MIL-STD-1553 Data from AIT MIL-STD-1553 interfaces in Chapter 10 Format - Software application which is Compatible with all AIT MIL-STD-1553 Interfaces - Capable of streaming data captured from one or multiple MIL-STD-1553 Bus Interfaces - Streamed data can be sent to a single network system or multicast on the Ethernet LAN - Compatible with AIT F-SIM-1553-AVOE analyzer or 3rd party Chapter 10 systems - Timestamps & Errors detected embedded in Chapter 10 stream
-
Product
Data Interfaces, Sensors And Actuators
-
Dewesoft also develops and manufactures data interfaces such as CAN USB devices, GNSS and INS positioning devices, and Inertial Measurement Units (IMU), and high-speed cameras. All devices are completely compatible and synchronized with all of our Data Acquisition (DAQ) systems and offer the same highest possible built quality. To complete the measurement chain we also provide high accuracy current and vibration sensors.
-
Product
Osprey / DX Co-Processor
9687
-
Double+ speed Osprey Co-Processor. Occupies one ISA/EISA PC slot. Writable control store, FPGA implementation of PDP-11 architecture with 4 MBytes of tightly coupled, zero wait-state memory. Includes FPJ11® compatible hardware floating point. Performance equivalent twice the DCJ-11® and 100%; of FPJ-11. On-card x86 microprocessor rapidly processes "virtual" I/O instructions. This card is used for Osprey/PC applications where all applicable I/O devices are emulated on the PC by Osprey software. Includes standard environment support for MS-DOS® V6.2.2. Windows/NT® environment support available.
-
Product
SA2500X, 2.5 GHz, ±8 V, 10X Attenuation, Single-Ended Active Oscilloscope Probe
784257-01
Oscilloscope Probe
The SA2500X is single-ended, active voltage probe that is used for many different high-speed measurement applications. The probe is powered by an included auxiliary power supply that is internationally compatible and certified. You can use it with oscilloscopes that provide 50 Ω input impedance.
-
Product
Color and Monochrome Camera
DP74
-
The DP74 color camera for fluorescence not only advances the speed and ease with which you can obtain detailed, accurate images but also introduces for the first time the concept of Intelligent Imaging. With Intelligent Imaging, the camera analyzes the live image and automatically applies its technology to reduce processing time and produce quality images of even dim and challenging samples. Furthermore the camera can follow your stage movements to create in real-time a panoramic image with mapped zoom-outs, a great time saver for documenting your sample. The DP74’s wide field of view and unsurpassed live speed provide an on-screen experience closely matching the traditional ocular view, thanks to its expertly calibrated colors. Maximize your investment return on a shared laboratory instrument with the camera’s top resolution of 20.7 megapixels and the capability to work with brightfield and fluorescent samples alike. These features are compatible with any microscope, whether manual or motorized, making the DP74 a perfect solution for a smarter and faster imaging workflow.
-
Product
Rack Mount Osprey Chassis 5.25" Qbus
97106-Q
-
5.25" high by 19" wide by 20" deep (134 x 483 x 508 mm), this chassis is FCC/CE certifiable**. A quad-height Qbus backplane, cooling fans, and slides are provided, diskette and hard drives (two visible 5.25" and two hidden 3.5" bays), and up to four quad-height Qbus compatible cards.
-
Product
USB Modular Multifunction Data Acquisition
U2300A Series
-
The U2300A Series USB Modular Multifunction Data Acquisition family consists of 7 modules - ideal for design validation and manufacturing engineers who conduct data logging, measurement or monitoring in a broad range of industries. All modules use the common non-proprietary standard high-speed USB 2.0 interface that provides ease of connectivity and comes bundled with the Keysight Measurement Manager (AMM) software. The U2300A series can function as a standalone or modular device that plugs into the U2781A USB Modular Product Chassis. These are also compatible with a wide range of application development environments such as Keysight VEE Pro, MATLAB2007a, NI LabVIEW and Microsoft Visual Studio. Get Keysights quality products at a low price.
-
Product
3.4 MP Autofocus Liquid Lens NVIDIA® Jetson TX2/TX1 Camera Board
E-CAM31_TX2
-
e-CAM31_TX2 is a 3.4 Mega pixel 4-lane MIPI CSI-2 liquid lens Auto focus camera board for NVIDIA® Jetson TX2 developer kit and it is also compatible with NVIDIA® Jetson TX1 developer kit. This camera is based on 1/3 inch AR0330 CMOS Image sensor from ON Semiconductor® with 2.2 µm pixel and A-Pix™ technology and an integrated high performance image signal processor (ISP). This S-Mount (M12) liquid lens camera enables autofocus with no mechanical moving part like VCM (Voice Coil Motors) will increase the lifetime and has an ability to focus and refocus in a matter of milliseconds.
-
Product
GPIB-RS485, GPIB Instrument Control Device
779733-04
GPIB Controller
Serial, RS485/RS422 GPIB Instrument Control Device - The GPIB‑RS485 is an IEEE 488 controller device for PCs with RS485 or RS422 ports. You can use this device to integrate an instrument into your system using GPIB. This device transforms a computer with an RS485 or RS422 … serial port into a talker, listener, or controller on the GPIB bus. It can also interface RS485 and RS422 instruments and peripherals to the GPIB bus. It can implement the physical and electrical specifications of the IEEE 488, RS485, and RS422 standards, as well as interpret and execute high-level commands from the serial port, including serial‑to‑GPIB, and GPIB‑to‑serial protocol conversions. This device is IEEE 488.2 compatible. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
Product
Quad Serial FPDP Interface with Virtex-6 FPGA - PCIe
Model 7811
-
Model 7811 is a member of the Cobalt® family of high performance XMC modules based on the Xilinx Virtex-6 FPGA. A multichannel, gigabit serial interface, it is idealfor interfacing to Serial FPDP data converter boards or as a chassis-to-chassis data link. The 7811 is fully compatible with the VITA 17.1 Serial FPDP specification. Its built-in data transfer features make it a complete turnkey solution. For users who require application-specific functions, the 7811 serves as a flexible platform for developing and deploying custom FPGA processing IP.
-
Product
Analog & Digital Gas Controller
MX 32
-
Teledyne Gas & Flame Detection
We introduce the new MX 32, a controller that takes analog & digital inputs and covers all needs for a wide variety of applications.The MX 32 is a compact, low-profile controller that continuously monitors gas detection and more generally any 4-20 mA, MODBUS RS485 signal from compatible detectors.
-
Product
Handheld Digital Multimeter, 4 digit, Water and Dust Resistant
U1271A
Digital Multimeter
Feature sets that meet traditional industrial requirements and improve productivity and safety Improved accuracy and resolution to meet traditional industrial requirements (30,000 counts resolution with 0.7% for ACV accuracy)Intelligent features to improve productivity and safety (selectable Low Pass Filter LPF and quick signal type identification Qik-V)Better grip Both visual and audible continuity indication in noisy environments Easy access to fuse for simplified maintenance Easy connectivity to PC and internal memory (up to 200) for data logging Large rotary switch and buttons that are easy to operate Dust and water resistant casing (IP 54 compliant)Compatible with U1177A/U1117A IR-Bluetooth adapter for remote monitoring & datalogging Altitude: 3000 meters
-
Product
STANAG3910/EFEX Test And Simulation Module for Standard Ethernet
ANET3910
-
STANAG3910/EFEX Test and Simulation module for Standard Ethernet. The ANET embedded Linux Operating System gives the unique capability to run the optional PBA.pro Engine right in the box. Another option is the ANET-ADK onboard software development kit where users create run-time applications (e.g. STANAG3910/EFEX to Ethernet Converter, STANAG3910/EFEX to Ethernet Gateway) to execute right in the box. For wireless applications, an ANET compatible USB Wifi dongle is optionally available.The capability to execute Python scripts in the ANET is a standard feature. For applications with multiple ANET devices AIM offers the ADock ANET Docking Station to host up to 4 ANET modules.
-
Product
8-CH ±10V Analog Output EtherCAT Module
EPS-4008
-
ADLINK" s EPS slave system features modular design for flexible high channel density, rugged construction, easy maintenance, and intelligent performance, compatible with 3rd party EtherCAT products. Precise time-deterministic control enables I/O synchronization for critical applications, and FPGA and ARM technology allow users to fully monitor status of EPS modules and systems, including operating temperature and usage cycle of relay switching, as well as motion control status for general purpose motor drive control. In addition, the ADLINK EtherCAT configurator enables auto-scan and configuration across EtherCAT systems. The EPS" unique structural and electronic design supports hot-swappable function, reducing repair time, and the rugged construction and operating temperature range of -20°C to 60°C allow operation in the harshest environments.
-
Product
Microcomputer Module
SX-23BT
-
The SX-32BT is a Bluetooth® 5.0 Low Energy compatible microcomputer module based on a 32-bit RX microcomputer, the "RX23W", from Renesas Electronics. Certified for North America, Europe, and Japan, the module's design also includes a PCB antenna. Furthermore, it adopts a 0.7mm pitch LGA package, ideal for OEM's looking to increase the efficiency of their manufacturing process while lowering the total BOM cost of their product.
