Crystals
-
Product
KNbO3 Crystals
-
All high-quality organic crystals are produced and optically prepared in the facilities of Rainbow Photonics in Switzerland.
-
Product
Electro-Optic DSTMS Crystals
-
DSTMS and other high-quality organic crystals are produced and optically prepared in the facilities of Rainbow Photonics in Switzerland.
-
Product
Frequency Synthesizer-Detector
SD-31
-
The Model SD-31 Synthesizer-Detector is a high output crystal signal generator of precisely known frequency combined with a sensitive, selective detctor for RF bridge measurements of AM antenna impedance. Packaged in a single light-weight battery-powered unit, the SD031 complements bridges such as the General Radio 1606, 916, and the Delta OIB-1.
-
Product
SPM Probes
-
AppNano silicon probes are manufactured out of prime grade, low resistivity (0.01- 0.025 Ω-cm), n-type antimony doped, single crystal siliconOur well-established silicon technologies combined with novel micro-fabrication processes achieve consistent high quality monolithic probes with unprecedented tip sharpnessWe have many standard silicon probe series designed for a wide variety of applications that are compatible with most AFM equipment in the market
-
Product
LED Tester For Packaging Machine
-
LED-501 is a single crystal packing tester. It can be utilized in electrical test.Two test results. Pass (GO) or fail (NG).Electrical Testing: Forward：VF Reverse：VZ,IRFour-wire measurement and contact resistance in case of deviation.Auto polarity identification and preheat function.Provide OPEN\SHORT count.Compatible mechanical interface.Connected with computer for measurement data collection.
-
Product
X-ray Fluorescence Sulfur/Chlorine-in-oil Analyzer
MESA-7220V2
-
The MESA-7220V2 measures both sulfur and chlorine in petroleum based products using the Monochromatic Energy Dispersive X-ray Fluorescence (EDXRF) method. A monochromatic X-ray source is used in order to obtain an ultra-low noise background which affords the best detection limits for both sulfur and chlorine.The detector window size was increased to collect more fluorescent X-rays and thus achieve lower level ppm values. This provides excellent, repeatable performance at both low and high concentrations of both elements.By adjusting the angle of the graphite crystal, the excitation beam can be measured to excite sulfur in the sample, increasing sensitivity.
-
Product
PXI-6683, TCXO, GPS, IRIG-B, IEEE 1588 PXI Synchronization Module
782109-01
-
TCXO, GPS, IRIG-B, IEEE 1588 PXI Synchronization Module - The PXI‑6683 timing and synchronization modules synchronize PXI and PXI Express systems using GPS, IEEE 1588, and IRIG‑B to perform synchronous events. The PXI‑6683 can generate events and clock signals at specified … synchronized future times and timestamp input events with the synchronized system time. The PXI‑6683 features an onboard temperature-compensated crystal oscillator (TCXO) that can be disciplined to GPS, IEEE 1588, and IRIG‑B for long-term stability. You also can use the PXI‑6683 to route clock signals and triggers with low skew within a PXI chassis or between multiple chassis, providing you a method for synchronizing multiple devices in a PXI system.
-
Product
Mechanical Products
-
*99 types of pin cut data are stored in the backup RAM and can be recalled whenever necessary.*Inputting unnecessary pins and cutting to the specified size is easy and clear as it is done while watching the pins appear on the LCD (liquid crystal display screen).*Changing to a different pitch can be done in a short time by simply replacing the sprocket and comb teeth.
-
Product
Class 100 Clean Ovens
-
These models are used extensively in heat treatment/drying or burn-in of semiconductor wafers, liquid crystals, disks and other components and devices requiring clean air conditions. These units can also be prepared for installation in clean-room environments. Class 100 cleanliness is achieved by employing a HEPA filter and a back-to-front laminar circulation system. The high-performance models (with MS suffix) provides stable performance even during heat-up or cooling.
-
Product
Vacuum Meters
-
Portable meters for absolute vacuum pressure measurements in hospital labs, crystal growing, solvent recovery, distillation, and rotary evaporation.
-
Product
Engineering Data Management SOoftware
EDM Modal
-
Engineering Data Management (EDM) is a PC-based software program designed for real-time data management and processing. This easy-to-use, Windows-native software manages the communication between the PC and all Crystal Instruments hardware platforms.
-
Product
Analytical Services
-
IGC: Inverse Gas Chromatography; Understand surface energies, polarities, acid/base properties and nanomorphology on powders and fibers. ToF-SIMS: Time-of-Flight Secondary Ion Mass Spectrometry. Localize your molecules at the first nanos! 2D imaging with resolution up to 200 nm. Highest sensitivity up to 10 ppm. CM: Quarz Crystal Microbalance In-situ observation of thickness and stiffness of any films in liquid environmentSEM: Scanning Electron Microscopy Images say more than words, especially with an artistic eye XPS/ESCA: X-ray Photoelectron Spectroscopy/Electron Spectroscopy for Chemical Analysis.
-
Product
TDR Test Set
TS® 54
-
Fluke Networks’ new TS52 PRO Test Set features the latest in test set technology. Designed with a superior, radiant liquid crystal display (LCD) user interface, it allows you to see what cannot be heard in any outside plant environment.
-
Product
Board
Arduino Leonardo with Headers
-
The Arduino Leonardo is a microcontroller board based on the ATmega32u4 (datasheet). It has 20 digital input/output pins (of which 7 can be used as PWM outputs and 12 as analog inputs), a 16 MHz crystal oscillator, a micro USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.
-
Product
Frequency Counter (225MHz - 18GHz)
S43180
-
S43180 series high-precision frequency counter is a high-precision frequency measurement instrument. It has a frequency measurement resolution of 10 bits per second. The whole machine scheme adopts countdown technology and digital interpolation technology to realize the high-precision measurement of the instrument. It has measurement functions such as frequency, period, frequency ratio and powerful mathematical statistics operations (maximum value, minimum value, average value, PPM, standard deviation, Allan variance).S43180 series has reliable performance, complete functions, high measurement accuracy, wide frequency measurement range, high sensitivity, large dynamic range, high cost performance and easy to use. It is especially suitable for frequency measurement in scientific research and measurement fields such as aerospace, crystal oscillators, and components.
-
Product
Portable Digital Manometer
PS309
-
Featured are an integral variable reluctance transducer, solid state electronics module, 3 digit liquid crystal display (LCD)* and battery pack with six 1.5V penlight cells for truly portable operation. The units can also be powered from an external DC power supply or AC battery eliminator (converter) module. The transducer features all corrosion resistant materials in contact with the pressure media (both ports in differential units), very low internal cavity volumes and ultra-low volumetric displacement with full-scale pressure excursion. Transducer calibration is unaffected by dielectric properties of the sensed fluid. Gauge and differential transducers may be disassembled and range changed by simple diaphragm replacement.
-
Product
Temperature compensated crystal oscillator
TCXO
-
A TCXO (Temperature compensated crystal oscillator) is a crystal oscillator with a temperature-sensitive reactance circuit in its oscillation loop to compensate the frequency-temperature characteristics inherent to the crystal unit. Epson's are classified into two types. One is a Direct-Type TCXOwith a temperature compensation circuit built into the oscillation loop. The other is an Indirect-Type TCXO with a temperature compensation circuit outside the oscillation loop, in which the oscillation frequency is therefore indirectly controlled.
-
Product
Mini Receiver
FB7-NX
-
In about 1935, the National Radio Company of Malden, Mass., brought out a “hot” high frequency receiver, called the FB7, and the subsequent FB-7X. It featured a super-hetrodyne design with plug-in coils that gave it a broad frequency range. The “X” model also incorporated a crystal filter in the intermediate frequency section, thus giving it additional selectivity. The receiver was viewed by radio amateurs as a technological breakthrough, and it was also used commercially for point to point high frequency communications. As the receiver did not have an internal RF amplifier section, a separately tunable RF amplifier was later provided in a separate enclosure for additional performance capabilities. Now, National RF, Inc., is resurrecting the fabled receiver name with an all solid-state, hot mini receiver, which also utilizes plug-in coils to cover the HF spectrum. The mini-receiver is designed for use by radio amateurs as well as serious short-wave listeners, and allows reception of AM, CW, and SSB signals. It incorporates a super-hetrodyne design with a dual gate FET built-in RF preamplifier and a ceramic filter for selectivity, often required when used in a crowded amateur radio band. In addition, the receiver has a buffered rear panel output of the high frequency oscillator for use with either a frequency counter for exact receive frequency display, or for interface with an outboard transmitter. A rear panel jack is also provided for muting the receiver when a transmitter is placed into the transmit mode. And, the receiver is small enough to fit into carry-on luggage and taken on trips when it is desired to “keep an ear” on amateur radio or other high frequency activity. The receiver utilizes rear panel plug-in coil assemblies which contain the RF amplifier, mixer, and oscillator tuned circuits. Each plug-in coil assembly also comes with a separate dial scale, which is inserted onto the front panel for displaying the tuned frequency. A very smooth 6 to 1 planetary drive is used for tuning the receiver. Other front panel controls include RF preamplifier peak, volume control, Beat Frequency Oscillator adjustment, and RF gain control. Other switches include filter bandwidth, AM/CW/SSB selection, Power, and a general coverage/band spread control for certain plug-in assemblies. The receiver is intended to drive head-phones via a rear panel jack, but has sufficient output to drive a small external speaker.
-
Product
Piezoelectric
-
CTS Corporation develops and manufactures state-of-the-art piezoelectric products, providing custom-made components that meet your exact geometrical, dimensional and performance specifications. Our product portfolio encompasses both bulk and multilayer piezoceramics, single crystals, printed thick film and built-to-print sensors and transducers. Our piezoelectric products are widely used across major industries including med-tech, aerospace/ defense and the industrial sector.
-
Product
Differential Scanning Calorimeters
-
Differential Scanning Calorimeters (DSC) measure temperatures and heat flows associated with thermal transitions in a material. Common usage includes investigation, selection, comparison and end-use performance evaluation of materials in research, quality control and production applications. Properties measured by TA Instruments’ DSC techniques include glass transitions, “cold” crystallization, phase changes, melting, crystallization, product stability, cure / cure kinetics, and oxidative stability.
-
Product
Medical Imaging
-
ams offers high-speed, low-noise and low-power sensing solutions that enable manufacturers of Computer Tomography (CT) equipment and digital X-Ray Flat Panel Detectors (FPD) to produce crystal clear images while exposing patients to low doses of radiation. We are taking our leading imaging sensing solutions and expertise forward to achieve an unprecedented level of image accuracy while enhancing convenience and safety for the user.
-
Product
Time-Resolved Electrochemical Quartz Crystal Microbalance
400C Series
-
The quartz crystal microbalance (QCM) is a variant of acoustic wave microsensors that are capable of ultrasensitive mass measurements. Under favorable conditions, a typical QCM can measure a mass change of 0.1-1 ng/cm2. QCM oscillates in a mechanically resonant shear mode under the influence of a high frequency AC electric field which is applied across the thickness of the crystal. Figure 1b below shows an edge view of a QCM crystal undergoing oscillatory shear distortion. The central portions of the top and bottom of the crystal are coated with a typically disk-shaped thin metal film (e.g., gold).
-
Product
Portable Multiple Frequency Signal Generator
PSX-6C
-
Matrix Test Equipment Incorporated
The Model PSX-6C is a portable, weatherproof Generator of clean, unmodulated, crystal- controlled, amplitude-variable outputs, up to +60 dBmV per channel. The PSX-6C is an improved version of the PSX-6 using enhanced technology and provides carriers that can be adjusted over a linear range of 15 dB.
-
Product
Three Phase Din-rail Multi-rate kWh Meter
SY 1041
-
Hong Kong Songyang Industrial Ltd.
Type SY1041 three phase DIN rail watt-hour meter is a kind of new style three phase electronic multi-rate watt-hour meter, energy data display adopt 7 digits wide temperature type crystal display, with many functions of multi-rate (time-of use) energy measurement, infrared carrier wave communication and RS485 serial port communication reading meter, etc
-
Product
Piezo-Electric Measurement Trainer Module
-
Unitech Scales And Measurements Pvt. Ltd
PiezoElectric Trainer comprises of piezoelectric crystal mounted inside housing and fitted on a base plate. Digital indicator is supplied to indicate the vibrational force.
-
Product
Hand-held Radioisotope Identification Device
RadEAGLET
-
Combining a large, high sensitivity crystal with a proven and tested intelligent algorithm, the RADEAGLET can quickly, accurately, and simultaneously detect and identify up to six isotopes, typically in under 30 seconds. The RADEAGLET performs well, even in complex shielded or masked scenarios. ANSI 42.34 compliant, the RADEAGLET offers a user-friendly interface that is intuitive, simple to navigate, provides visually clarity, and utilizes an extensive array of alarms. Supports NaI(Tl) and LaBr3(Ce) to optimize performance across multiple applications.
-
Product
Infrared Thermometer
-
Display: 3 1/2 digit liquid crystal display (LCD) with amaximum reading of 1999.Polarity: Automatic, positive implied, negative polarityindication.Low battery indication: the " " is displayed when thebattery voltage drops below the operating level.Operating environment: 0°C to 50°C at<75% relativehumidity.Storage temperature: -20°C to 60°C, 0 to 80% R.H.withbattery removed from meter.Accuracy: Stated accuracy at 23°C±5°C, <75% relativehumidity.Auto power off : 10 secondsDimensions: 148mm(H) x 105mm(W) x 42mm(D).
-
Product
Parallel Seam Sealers
-
It is an equipment to hermetically seal the packages, such as the crystal and SAW devices, optical devices, sensors, MEMS, etc., by seam welding. Hermetic sealing can be accomplished in both N2 and vacuum environment. Furthermore, we are offering a variety of products for research and development and production applications.
-
Product
10 GHz Signal Source
YIG Series
-
The SC5503B and SC5502A are designed to meet demanding low phase noise applications. This is accomplished by employing a multiple phase-locked loop architecture as well as a YIG oscillator as the heart of its synthesizer. Frequency accuracy is provided by an onboard 10 MHz temperature compensated crystal oscillator (TCXO) which can be phase locked to an external reference source if required. These modules can be used as standalone CW signal sources or as LO sources for frequency conversion systems such as the SignalCore IQ modulators and demodulators. They are designed to meet the requirements of many modern applications such as wireless device testing, software-defined radio research, point-to-point radio, multi-channel coherent systems, and other academic and military programs.
-
Product
Phase-Locked Crystal Oscillator
PLXO Series 0.9” x 0.9” x 0.25”
-
*Compact Surface Mount Package *Excellent Phase Noise and Stability *Configurable for any application
