Audio Test Systems
See Also: Audio Test, Audio Testers, Speaker, Acoustic
-
Product
Dynamometer Test Systems
-
Genuen provides a full range of off-the-shelf and custom dyno test cell solutions. We offer turnkey test cell integration services and test cell upgrades and modernization for all types of dynamometers used in automotive, aerospace, industrial, commercial, off-highway, and agricultural markets. Our broad-based expertise includes dynamometer test systems ranging from AC motor, hydrokinetic, hydrostatic, electric AC/DC, eddy current, and hysteresis brake.
-
Product
SAS Protocol Test System
M124A
Test System
The SAS Sierra M124A Protocol Test System is Teledyne LeCroy's 7th generation protocol analyzer system that provides 100% accurate protocol capture of both SAS (SAS 3.0) and SATA (SATA 3.0). The industry's most widely used test platform for SAS and SATA features unmatched analysis and debug capabilities to help pinpoint problems at every layer of the protocol.
-
Product
Audio Generator
AG-51
-
The AG-51 Audio Generator contains a low distortion 20 Hz to 200 kHz sine wave generator, an SMPTE standard intermodulation signal generator and a fixed frequency sine wave generator at 3.15 kHz for wow and flutter tests. Signal outputs are simultaneously available at levels of up to +20 dBm (equivalent sine wave power for complex signals) at separate left (L OUT) and right (R OUT) output connectors. Outputs may be selected for left (L) only, right (R) only, left and right in phase (L+R), and left and right in phase opposition (L-R). Fully balanced or unbalanced outputs at impedance levels 150 ohms or 600 ohms are front panel selectable. Three precision attenuators (10, 1.0 and 0.1 dB) provide a dynamic range of 99.9 dB in 0.1 dB steps. Attenuator dials display the output level directly in dBm in the 150 ohm source impedance configuration. Automatic output leveling circuitry with a built-in self-test feature provides a constant output level thereby eliminating the need for output metering. In the TEST mode the generator output level is reduced to zero, a useful feature during noise measurements.
-
Product
Automotive Test Systems
-
Ono Sokki Automotive Test Systems - flow meter, non-contact speedometer, engine tachometer, crank angle detector, and more
-
Product
Automated Testing System
PV-LIT
-
Thermographic solutions ensure high quality of solar cells and modules.Usable for all types of solar cells and modules (silicon-based or thin-layered)Testing in laboratory and in-line in the course of the manufacturing processTesting of various solar cells and modules through contact and non-contact measurementCell-specific system configuration and determination of test criteria and kind of defects
-
Product
Component Test Fixture For N1413 With B2980 Series
N1428A
Test Fixture
The N1428A is designed to operate specifically with the B2985B / 87B electrometer / high resistance meter. It is provided with two component modules, which are used to hold SMD, lead, and various types of devices. Electrical noise effects are reduced by the employment of a shielded case. A built-in interlock circuit enables safe high-voltage measurements. The N1413A high resistance meter fixture adapter is also required to connect the N1428A to the B2985B / 87B.
-
Product
IT Battery Test System
-
Shenzhen Sinexcel RE Equipment CO., Ltd
IT battery test system support for multiple charging mode (such as CC, CV, CP, pulse, etc.) and discharge mode, to ensure that the battery performance and safety in the practical application. IT battery test system is designed to be modular, easy to maintain, and with anti-reverse connection, data loss and other protection functions
-
Product
Audio Monitors
TouchMonitor TM9
-
The all-new audio metering units of the TouchMonitor range is RTW‘s answer to growing requirements in today‘s production, post-production, and broadcast world. Equipped with high-grade 7“ or 9“ touch screens and an easy-to-use GUI, TouchMonitor enters a new level of professional audio metering in terms of precision, performance, efficiency and flexibility.
-
Product
Laser Test Systems
-
Santa Barbara Infrared, Inc. offers an extensive family of test systems and components that test and characterize the performance of laser range finders, designators, illuminators and spot trackers.
-
-
Product
Automotive Audio Processors
-
ST’s wide portfolio of analog and digital signal processors covers the full range of features and channel configurations for the car-audio application spectrum, from low-end solutions to high-end premium audio systems. More than 40 analog signal processors offer a large choice for the number of inputs, number of output channels, and baseband audio functions, including EQ, dynamic compressors, subsonic filters, and more. Alternatively, a fully digital solution with embedded 20-bit audio ADCs and DACs is based on a proprietary 24-bit DSP specifically crafted for audio applications.
-
Product
Memory Test Systems
T5503HS2
-
Semiconductor memories are in high demand to meet the needs of fast-growing end markets such as portable electronics and servers. It has been forecasted that applications ranging from mobile devices and data centers to automobiles, gaming systems and graphics cards will consume an estimated 120 billion gigabits of DRAM capacity. To meet this market demand, new generations of memories with data-transfer speeds of 6.4 Gbps and higher are being developed. Advantest’s second-generation T5503HS2 tester is designed to handle these ultra-high-speed memory ICs.
-
Product
MEMS Test System Development
-
olidus Technologies’ can design and build a test system customized for your exact needs, using our own or off the shelf components:Custom MEMS Test Systems. We can integrate and assemble test equipment and handling systems to fit your requirements. Custom MEMS Test Software. We can write custom software for device-specific calibration and testing, interfacing various instruments and handling systems, or create a customized GUI. We can also adapt our standard STI Test Software to work on your hardware system.
-
Product
Audio Analyser
ATB PC Pro
-
The ATB PC Pro Measuring system is a professional Audio Analyser. The Windows program is combined with the computer’s soundcard, the measurement microphone, the Test-Box and the DVD (CD) for the signals forms an exact and extensive measurement system. The applications for the ATB PC Pro are the speaker development, room acoustic optimise, the installation of car sound systems, the setting of Surround reproduction systems and the noise analyser.
-
Product
Hardware-in-the-Loop Test Systems
HIL
-
Our early development efforts and NI VeriStand expertise uniquely qualify us to maximize the benefits of and provide top-notch integration services for this software platform. Wineman Technology offers powerful and flexible MIL and HIL testing solutions, such as: Full range of MIL and HIL test systems. Software for testing. Software for simulating electronic control modules. Fault insertion unit (FIU)..
-
Product
Flying Probe Test System
A8a
-
The A8a test system provides the flexibility of flying probe testers while delivering high throughput testing for bare board printed circuit boards (PCBs). The target market for the A8a is the electrical test of tablet and PC motherboards and high density interconnect (HDI) products for smart phones. The A8a is designed for high productivity, reliability and test accuracy. To achieve high throughput the key feature of the A8a is a new dual shuttle system, which reduces the product exchange time to zero seconds in automation mode. In combination with the fast test speed of up to 140 measurements/second the A8a will give customers a competitive test solution for batches up to 5000 boards. A typical cycle time of a 4-up smart phone board is about 2 minutes.
-
Product
Noise Figure Analysis Using NI PXI RF Test Instruments
NI-RFmx Noise Figure
Test Instrument
Measure noise figure, gain, Y-factor, effective temperatures, hot and cold power, and moreOptimized calibration and measurement routines for multi-DUT test using Y-factor and cold sourceSupports the PXIe-5668R 26.5 GHz VSA, the PXIe-5698 26.5 GHz preamplifier, and VSTsDesigned for use with industry-standard noise sources such as the Noisecom NC346 Series
-
-
Product
Spring Clip Fixture
16092A
Test Fixture
Use this test fixture with parallel electrodes for impedance evaluation of both lead and SMD components.
-
Product
Software-based Electroacoustic Test System
SoundCheck
-
The SoundCheck®system from Listen includes everything you need to perform audio measurements on a wide range of devices – the software, the audio interface, other test interfaces and accessories, and test sequences. The system is centered around the SoundCheck software. This powerful package controls and communicates with the measurement hardware, and includes all the stimuli, algorithms and analysis functionality needed to develop and run virtually any electroacoustic or audio electronic test. It is paired with hardware ranging from a simple, all-in one audio test box to sophisticated discrete components for a complete test system. In addition to Listen hardware, a range of 3rd party products and test accessories are fully supported within SoundCheck.
-
Product
Compliance Test Systems
LMG Test Suite
-
ZES ZIMMER Electronic Systems GmbH
The ZES ZIMMER test system LMG Test Suite tests in accordance with the currently valid version of EN 61000-3-2/-12 or EN 61000-3-3/-11 and also supports measurements per ECE R-10.4 Annex 11 (e.g. electromagnetic compatibility of vehicles). As a manufacturer of precision power measurement technology, we are represented on the international standards committee. As a result, changes in standards are immediately incorporated into our test systems.
-
Product
Test System
LB301
-
Computer Gesteuerte Systeme GmbH
The system is pin and software compatible to the larger test systems LB302 / 303. Due to the fewer needed I/Os, the tester features the compact G6 receiver (Virginia Panel Cooperation) compared to the larger G12 of the other tester versions. The LB301 is equipped with a 2kW power supply and can control one load box.
-
Product
3-in-1 Test System
CIBANO 500
-
CIBANO 500 combines a micro-ohmmeter, timing analyzer, and a coil and motor supply. All important CB tests on all types of CBs can be carried out even when a station battery is not available.
-
Product
Electro-Stimulation Equipment Testing System
STIMU-600
-
Test device for functional testing of electrical stimulation devices.
-
Product
(2500kN+) Fatigue Testing Systems
8806
-
The precision mechanical systems, combined with the advanced features of the 8800 digital controller and Dynacell™ load cells, enable Instron to supply fully-integrated turnkey solutions to meet the most demanding applications. The system can be used to cover a broad range of static and dynamic test applications, covering metals, rebar, high-force fracture mechanics, aerospace panels, civil engineering components, wire ropes, or concrete.
-
Product
Wizard Pocket Audio Monitor
AES/EBU
-
The AES/EBU Wizard is a hand-held digital audio monitor that receives AES/EBU audio at any sampling rate from 32kHz to 96kHz and displays the received sampling rate, lock status, and five different error conditions. It also has a headphone jack with volume control for monitoring digital audio sources.
-
Product
Audio Test Tone Generator
ToneGenerator
-
Tone Generator is a sine wave generator, frequency generator and signal generator that lets you create audio test tones, sweeps or noise waveforms using your computer or a PDA handheld. Generate sine wave, square wave, triangular waveform, saw tooth waveform, impulse, white noise and pink noise.
-
Product
Test System
ITC57300
-
The ITC57300 Dynamic Parametric Test System mainframe accepts Test Heads that perform nondestructive transient measurements on semiconductor devices such as Insulated Gate Bipolar Transistors (IGBT), power MOSFETs, diodes, and other bipolar devices(requires additional optional bias power supplies and custom personality boards). Included in the mainframe are all test equipment and software necessary to analyze and perform resistive and inductive switching time, switching losses, gate charge, Trr/Qrr, and other transient tests.
-
Product
Zero-distance Drop Test System
KRD40 series
-
KRD40 series drop tester, mainly simulates the resistance to drop and impact of large and heavy packaging products. Its strong power system and unique sample holder facilitate easy loading and unloading of oversized and overweight items and automatically rise to the setting. After the height, the drop test is completed. It can realize the drop test of the edge, surface and angle of the sample. This equipment is mainly used to evaluate the ability of product or packaging to withstand drops during transportation and loading and unloading, so as to improve product and packaging design.
-
Product
Chloride Test System
C-CL-2000
-
The C-CL-2000 produces results on-site, within minutes that are accurate and comparable to expensive laboratory tests. It measures the electrochemical reaction of a weighted sample placed in an extraction liquid. It automatically shows a temperature compensated reading of percent of chlorides on its digital display. A wide range - from 0.002 to 2% chloride by weight - is covered.
