Voltage Current Sources
See Also: Current Sources, Voltage Sources
-
-
Product
Optical power meter with Optical laser Source
-
Shanghai Baudcom Communication Device Co.,Ltd.
The Multimeter combines a power meter with a 2-wavelength laser source,for optical fiber network installation and maintenance. With the large capacity of data storage,it's very convenient for field testing and transfering the test results to PC through USB interface.
-
Product
Multifunction Voltage Tester
-
*Detects AC voltage by non-contact method: 70VAC to 250VAC*Finds broken wire location*Wrong connection check*Ground / Earthing disconnection check*Detects static radiation of TV / monitor*Checks operating condition of ionizer*Microwave leakage detection: ≥5mw/cm2
-
Product
Precision Calibrated Noise Sources
-
ELVA-1's calibrated noise source ISSN-XX series delivers a uniform level of noise power spectral density within the whole waveguide frequency range. Sources are available in eight waveguide bands covering 26.4-170 GHz.
-
Product
In-fuse Vehicle Current Measurement System
Sens-X
-
Sens-X intelligent sensors offer a range of high dynamic range sensor hardware for the capture of specialist current measurements.
-
Product
LXI High Voltage Switching
65-233-902-HI
-
The 65-233-902-HI plug-in module is part of a scalable high voltage switch platform that provides a high voltage switching solution with capability up to 9 kV.
-
Product
Low Input Bias Current Amplifiers (<100 pA)
-
Low input bias current op amps are required whenever the difference of currents or voltage is small and needs to be measured accurately. These op amps are used so that the signal is not loaded down by the input of the op amps. Low input bias current op amps are critical for interfacing sensors in applications from photodiodes, pH meters, or other electrometer related functions to downstream electronics. Analog Devices has many precision op amps that fit the definition and range of these applications.
-
Product
Impulse Current Test Systems
-
Fivestar HV Testing Equipment Co., Ltd.
Impulse current test systems are mainly used for testing transmission and distribution systems against the effects of direct or indirect lightning strokes or against electromagnetic interference effects. Primary application of impulse current test systems is the testing of surge arresters, nowadays mainly of the metal-oxide type (MOA) and surge protection devices (SPD). Now they are also widely used to test vehicles, aircrafts, and military applications.
-
Product
Shaft Voltage Tester™ Digital Oscilloscope
AEGIS®
-
Digital Oscilloscope and Multimeter with Conductive Microfiber Probe Tips. Is your motor safe from destructive shaft voltages? For the first time you can get all of the tools to find out in one place. The AEGIS® Shaft Voltage Tester™ Digital Oscilloscope bundle includes the AEGIS-OSC-9100 100 MHz digital osciloscope, shaft voltage probe tips, and a shaft grounding simulator. Armed with these tools, you can quickly and easily find whether your motors are at risk of premature bearing failure due to VFD-produced bearing currents.
-
Product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-200B Open loop method
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
Product
Portable Eddy Current Flaw Detectors
-
Portable eddy current (EC) flaw detectors inspect metallic parts and perform highly reliable and advanced flaw detection of surface and near-surface defects. Olympus offers portable eddy current equipment to meet a broad range of applications, including the detection of surface or near-surface defects, and the inspection of bolt holes.
-
Product
Optical Light Source
CARY-LS300B
-
The CARY-LS300B optical light source provide 1310/1490/1550 nm three outputwavelengths to meet specific application requirements. It is a idea solution for the fiberoptic network characterization, out-door network construction inspection and lab application.
-
Product
Incoherent Sources
-
Our Incoherent Sources include unmounted LEDs, mounted LEDs, collimated LEDs, LED light sources, superluminescent diodes, and broadband light sources. Our collimated LEDs are particularly popular and are compatible with many microscopes. Versions are available with center wavelengths from the UV into the NIR or that emit white light.
-
Product
Digital Eddy Current Displacement Sensor
ZET 7140-S
-
A digital eddy current sensor consists of a primary transducer (eddy current probe) and the ZET 7140-S measuring unit.
-
Product
High Voltage Test Station
-
High-voltage test stations place high demands on the safety aspect. We design these test stations in cooperation with our manufacturers as self-sufficient test systems.
-
Product
Single Filament Sources
-
Get a cost-effective solution that’s ideal for your high-volume, high-value MBE process needs with reliable Veeco Single Filament Sources. They feature dependable band thermocouples and single heater filaments for 750-1200°C operation. Three system configurations, and many crucible sizes, are available. All offer stable and consistent fluxes of high vapor pressure materials.
-
Product
High Voltage Snubber Capacitor
STP-01RN / STP-01RB
-
This series of capacitors is Plastic Enclosure, Dry construction design and doesn't have leakage problem when compared with traditional Metal Enclosure Oil impregnated capacitors.Handle high surge current, RMS current and surge voltage with Temperature up to +105CCapacitance : 0.25uF - 60uF ( can be customized )Voltage range : 900Vdc to 5,300Vdc / 280Vrms to 1,600VrmsRMS Current - Irms : up to 80Armspeak to peak pulse current - Ipp : up to 15,000AppTemperature ranges : +85C / +105C
-
Product
Three Phase Secondary Current Injection Test Set
TEST-330B
-
Beijing GFUVE Electronics Co.,Ltd.
Three phase secondary current injection test set is testing relay set, protective device, instruments, output ac dc current and voltage source, embedded Window XP system.
-
Product
High Current Generators
-
Quantum Composers is a recognized industry leader for Current Pulsers and Firesets. We specifically design our units for use in pyrotechnic applications such as Aerospace, Defense, Propulsion, and Automotive Safety and Squib testing. Our current generators are used throughout the world in demanding and harsh testing environments where quality, reliability, and safety are paramount. We are also an excellent replacement and upgrade solution for legacy equipment.
-
Product
AC DC High Voltage Break Down Tester
-
RR – AC DC HIPOT TESTERS can perform such precise dielectric test in a cost effective manner without any compromise on safety. Our hipot testers are custom made to suit needs of various industries and product ranges. A Singe tester can be used for conducting both AC and DC Insulation Testing.
-
Product
Surge Voltage Generator
SSG 3000
-
Cable fault location with the BAUR SSG 3000. Surge voltage generators are used for pre-location and pinpointing of high- and low-resistive as well as intermittent faults in power cables. The energy stored in a high-voltage capacitor is released at regular intervals or as DC voltage. The thus generated acoustic signal at the fault position can be recorded with a ground microphone and a universal receiver.* High surge voltage up to 32 kV* Continuously adjustable voltage* Voltage monitoring through kV meters with 3 measuring ranges* high surge energy in each voltage range
-
Product
PXI High Voltage Programmable Resistor Module, Connector
40-230-256-HI
-
The 40-230-256-HI (PXI) and 42-230-256-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4.5Ω and 76.8MΩ with 8Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Safety Voltage Detector
325 SVD
-
Standard Electric Works Co., Ltd
● Compact, easy to wear and convenient in use● Designed for indoor and outdoor use● Water-proof design. (IP65)● Equipped with self-testing functions● Able to sense all kinds of AC High Voltage System● Low power consumption● CE Certifiedright LED visual indication
-
Product
Current Sensing
-
A current sense amplifier is a differential amplifier providing an analog output voltage proportional to the current flowing into a load connected on its input.
-
Product
Low Voltage DC / Battery Powered HV Amplifiers
WMA-02 And WMA-02LF
-
The Falco Systems WMA-02 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 4mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-02LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.2mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
Product
Pulsed Laser and LED Light Sources
NanoLED
-
The NanoLED range is a novel and economical light source system that utilizes pulsed laser diode and LED technology to generate short optical pulses over a wide range of repetition rates and wavelengths. Optical pulses as short as 70ps can be generated at repetition rates up to 1MHz.
-
Product
USB Voltage Measurement Bundle
-
The USB Voltage Measurement Bundle provides a portable, USB-based sensor measurement system that helps you measure input voltage signals while providing isolation and overcurrent protection for high-voltage applications.
-
Product
Light Sources
-
These external units provide illumination which is transmitted to the viewing instrument by a light guide cable, and then through the scope via the integral fiber bundle to the viewing tip.
-
Product
3 In 1 Metal Voltage Stud Detector
NT-6352
-
Combined unit to accurately detect live or dead electricity cables, water or gas pipes and wooden studs or battens.LED & buzzer indicators.Depth penetration 18~20mm.Using precision screwdriver for easy unit sensitivity adjustment.Power source: NEDA1604/6F22 (9V) x 1pcs(Not included).Size: 178 x 120 x 34.7mm.
-
Product
Controllable, Programmable Linear DC Source With Load
LAB / SL
-
*Linear laboratory power supply*Integrated electronic load*Linear regulated DC laboratory power supply*No thyristor pre-regulation, very little ripple*Various interfaces · Built-in electronic load*Protection against short circuit, overload and overtemperature*Constant current and constant voltage*Fast control times approx. 250 µS
