-
Product
Crease And Stiffness Tester
DRK153
-
Shandong Drick Instruments Co., Ltd.
Whether this is by hand or by mechanical means. The crease recovery (spring back) can result in forces, which distort the erected carton or cause stresses to be applied to closures, which reducetheir effectiveness. With the Crease and Stiffness Tester, the Crease recovery is determined by the decrease in resistance offered by creased board after it is folded 90° at the crease measuring the recovery force after 15 seconds. Board Stiffness is determined by bending a 50mm length of board through a 15° angle.
-
Product
Repeat Durability Tester
TIQ1000
-
It is a device to measure repeated endurance such as limit bending test of board, endurance test of mounted board, endurance test of connector, etc. Continuity data and load data can be obtained during the cyclic endurance test. Conforms to JEITA ET-7407 "Environmental and durability test methods for mounted CSP/BGA packages".
-
Product
Cold Ross Flex Tester
UI-FT27B
-
Cold Ross Flex Tester – Ross Flex Machine is used to test the cut growth in rubber vulcanizates under continuously bend flexing in 90° in low temperature chamber. Ross Flex Test Method includes ASTM D1052, SATRA TM60, ISO 4643 and etc. Ross flex machine is one of the most common sole testing machines in footwear testing Lab.
-
Product
Semi-Rigid Cable, 3.5 Mm (Test Port) To 3.5 Mm
85131G
-
The Keysight 85131G is a 53 cm (21 in) long1 semi-rigid cable with a 3.5 mm female2 to 3.5 mm male connector. Cable frequency range is dc to 26.5 GHz with a return loss of 16 dB or better. Insertion loss is 0.3 * sqrt (f) + 0.2 dB (where f is frequency is GHz) for the test port connector, and 1.8 dB at maximum frequency for the device connector. Phase stability of semi-rigid/flexible cables is characterized with a 90 degree bend using a 4 inch radius. Stability1 of the Keysight 85131G is 0.06 dB and phase is 0.16o * f + 0.5o (where f is frequency in GHz).
-
Product
Wire Bend Tester
-
CSZ chamber is designed for this type of cold bend test. Each chamber is designed to meet the customer's size and temperature requirements. Chambers feature power-driven mandrels that are typically mounted at the top and bottom of the chamber for the wire to wrap and bend around. Mandrel diameters are selected by the customer and supplied in a variety of sizes.
-
Product
Fiber Visual Fault Locator
-
Fiber visual fault locator is a pen type device which is able to locate the breakpoint, bending or cracking of the fiber glass,this small fiber optic equipment can locate the fault of OTDR dead zone and make fiber iIdentification from one end to the other end .
-
Product
Shoe Bending Stiffness Tester
UI-FT25
-
Shoe Bending Stiffness Tester is used to test shoe stiffness/rigidity by flex shoe to certain angle by certain force.
-
Product
Dual Space Electro-hydraulic Servo Universal Testing Machine
WAW-E Series
-
Jinan Testing Equipment IE Corporation
WAW-E series computer control servo-hydraulic testing machine is suitable for testing tension, compression, bending and shearing strength of various metallic & non-metallic materials. Equipped with the electronics, computer &software packages, the servo-hydraulic tester of dual space is capable of controlling the test procedures by the predetermined programs. The computer control servo-hydraulic testing machine can also display, record, process and print the test results. The test curves can be drawn automatically in real time. The servo-hydraulictesting machine is easy to operate and is versatile in the applications of metallurgy industries such as steel mills & alloy, reinforced bar, aircraft manufacturer, research institutes, laboratories, calibration institutes etc.
-
Product
Flexible Cable Set, 3.5 Mm (Test Port) To 7 Mm
85132F
Calibration Cable
The Keysight 85132F is a 62.9 cm (24.75 in) long¹ flexible cable set composed of two 3.5 mm female² to 7 mm connectors. Cable frequency range is dc to 18 GHz with a return loss greater than or equal to 17 dB. Insertion loss is 0.25 * sqrt(f) + 0.2, where f is frequency in GHz, for the test port connector and device connector. Phase stability of semi-rigid/flexible cables is specified with a 90 degree bend using a 4 to 3 inch radius. Stability¹ of the Keysight 85132F is less than 0.12 dB and phase is 0.13 * f + 0.5, where f is frequency in GHz.
-
Product
VTAC, Patchcord, ITA, 36", VTAC, DACAR 535, to Rosenberger
7-141702731-036
VTAC Patchcord
The density/ thickness of DACAR 535 wire may require a module loading pattern that includes extra slot spacing to prevent wire bend and pressure. See the VTAC User Manual for more information.
-
Product
Pen-based Fault Locator
-
*Find the breakpoint, bending or cracking*Find the fault of OTDR dead zone*Identification of fiber from one end to other end*Universal adaptor*Testing distance up to 8km*Lightweight, red laser output, both SM and MM available
-
Product
Bending Stiffness Test Fixture
-
Q-Card’s bending stiffness fixture features splayed feet and aggressive no-slip rubber pads for stability. It is manufactured of aerospace-grade aluminum alloy with a hard anodized, scratch-resistant, durable finish to provide years of rigorous testing and trouble-free service.
-
Product
Adjustable Press Plate Bed of Nails Testers
Rand Adjustable Family
-
esigned for Research & Development and Pre-Production environments to support often reoccurring product design changes. The primary design focus for this fixture is ease in applying engineering changes and resilience to the abuse of applying multiple engineering changes without damage. In R&D and Preproduction, design changes and updates can occur every week. This Rand fixture, unlike normal test fixtures was designed to be easily taken apart and updated. Constantly disassembling modifying and reassembling a normal bed of nails test fixture over and over again can be a major disaster with wire breakage and test pin bending issues. The modular design of the Rand fixture allows for easy disassembly without flexing the wires or risk of bending test pins. The Rand fixture provides complete easy access for multiple updates requiring machining, drilling and wiring changes.
-
Product
Demattia Flex Tester
UI-FT33
-
Demattia Flex Tester & Demattia Flex-Cracking Tester is used to test rubber crack growth under repeated bending or flexing. Unuo manufactures demattia flexing fatigue tester which meets test methods of ASTM-D813, GB/T 13934, HG 2873, ISO 132:1999(E), BS 903-A10 and etc.
-
Product
Cable Fault Locators
-
Wuhan Sunma Technology Co., Ltd.
Visual Fault Locator, we can understand its function in the letter. It could be regarded to be part of OTDR and the fiber fault locator is cheap. Fiber visual fault locator is a kind of device which is able to locate the break-point, bending or cracking of the fiber glass. It can also locate the fault of OTDR dead zone and make fiber identification from one end to the other end. Designed with a FC,SC,ST universal adapter, this fiber testing red light is used without any other type of additional adapters, it can locates fault up to 10km in fiber cable. SunmaFiber also supply a new kind of Cable Fault Locator, Fiber laser tester/ fiber laser pen, it can locates fault up to 30km in fiber cable. Contact us at Sales@SunmaFiber.com or Live Chat with us. Save your money & time right now! Buy from fiber optic supplies at SunmaFiber.com with your confidence.
-
Product
Economical Single Point Bending Beam Load Cells
ESP SERIES
-
The ESP Series is a economical, high accurate single point bending beam load cell. It is ideal for OEM applications such as electronic scales and weighing machines. The single point bending beam design is highly resistant to eccentric loading allowing direct mounting to the scale base and weighing platform. The ESP Series features a moisture proof sealant.
-
Product
Beam Bender
10726A
-
The Keysight 10726A bends the incoming beam at a 90-degree angle and is designed for beam diameters of 9 mm or less. This bare optic requires a user-supplied mount.
-
Product
Fatigue Rated Low Profile Cells
-
Fatigue rated load cells are specifically designed for component durability and fatigue test machines where highly cyclical loading is present. These rugged load cells are extremely resistant to extraneous bending and side loading forces. They are used for material testing, component life cycle testing and structural testing. All fatigue rated load cells are guaranteed against fatigue failure for 100 million fully reversed cycles.
-
Product
Conical Mandrel Bend Tester
1510
-
The Elcometer 1510 Conical Mandrel Bend Tester is used to determine the effects of bending on the elasticity, adhesion and elongation properties of cured coatings on sheet metal.
-
-
Product
Optical Fiber Identifier
AFI-500
-
Shanghai Fibretool Technology Co.,Ltd.
AFI-500 Optical Fiber Identifier can quickly identify the direction of transmitted fiber and display the relative core power without any damages to the bended fiber. When the traffice is present,the intermittently audible tone is activated.
-
Product
500KG MicrocomputerTensile Test Machine
CX-106
-
Shenzhen Chuangxin Instruments Co., Ltd.
The Tensile Testing Machine is widely applied to test the tensile, tear, peel, and bend of all kinds of materials, such as metal, cable and etc, it’s used to test the tensile, tear, peel, compressive strength and bending of the material. It conforms to the standard of GB, ISO7500/1, JJG475-88, ASTME4, DIN5122, JISB7721/B7733, EN1002-2, BS1610, and CNS9471/9470.
-
Product
ZIF (Zero-Insertion-Force) Socket
Series 516
-
Zero Insertion Force Socket. A choice of 24, 28, or 40 pin count devices can be inserted without bending or otherwise damaging the legs, since no force is required to either insert or remove the component from the socket. Contacts are normally open and are closed by a unique cam action controlled by dual lever arms. The last 15° of movement of the cam provides a wiping action to the contacts on the legs of the device to remove any residue, ensuring a gas-tight seal.
-
Product
R&D Clamshell Bed of Nails Testers
Rand Press Rods Family
-
Designed for Research & Development and Pre-Production environments to support often reoccurring product design changes. The primary design focus for this fixture is ease in applying engineering changes and resilience to the abuse of applying multiple engineering changes without damage. In R&D and Preproduction, design changes and updates can occur every week. This Rand fixture, unlike normal test fixtures was designed to be easily taken apart and updated. Constantly disassembling modifying and reassembling a normal bed of nails test fixture over and over again can be a major disaster with wire breakage and test pin bending issues. The modular design of the Rand fixture allows for easy disassembly without flexing the wires or risk of bending test pins. The Rand fixture provides complete easy access for multiple updates requiring machining, drilling and wiring changes.
-
Product
Passive Components
-
VDI offers a wide variety of waveguide sections, tapers, antennae, and bends for your application. Please note that external dimensions are subject to change.
-
Product
Terminal Mechanical Strength Test
-
The terminal strength test is used to performed to determine whether the design of electrical terminals and their method of attachment can withstand mechanical stresses to which they will be subjected during installation or disassembly in equipment. These stresses must be withstood by the component without sustaining damage which would affect either the integrity of the terminals or the operation of the component part itself. Procedures are established in this method for testing, for example wire-lead terminals, flexible-flat-strip or tab-lead terminals, and rigid-type terminals which are threaded or have other arrangements for attaching conductors. The forces applied during the test consist of direct axial, radial or tension pulls, twist, bending torsion, and the torque exerted by the application of nuts or screws on threaded terminals.
-
Product
Card Impact Tester
-
Tests corner impact and card bending resistance, Designed to test for MasterCard CQM and ANSI N322 requirements, Easy to use, Repeatable results, Small footprint design for benchtop use, Adjustable jaws allow use with various card thicknesses, Super heavy duty custom CNC design
-
Product
VTAC, Patchcord, ITA, 36", VTAC, DACAR 535, to Receiver, VTAC
7-141702142-036
VTAC Patchcord
Please note: The density/ thickness of DACAR 535 wire may require a module loading pattern that includes extra slot spacing to prevent wire bend and pressure. See the VTAC User Manual for more information.
-
Product
iCon XL (High Power)
-
VPC's iCon XL (High Power) connector features all of the same benefits as the iCon, but with a larger bend radius and enlarged cable exit to support high power cables. Supports iCon High Power module with up to (6) 150 amp contacts. Fully wired connectors are available with flying leads. Visit the High Power page to learn more about VPC's offerings for high power.
-
Product
Flexing Tester
-
Premier's Flexing Tester are used to check how much the bending movement of the cord influences the electrical and mechanical connection.
