Filter Results By:
Products
Applications
Manufacturers
-
product
Optical Comparator
Golden Units
The use of the Golden Units is the easiest way to ensure that your production devices are inspected to the accuracy you expect. The use of an optical comparator brings into play the subjectivity of the operator and errors induced by bending leads on real parts during handling by the operator.
-
product
VTAC, Patchcord, ITA, 36", VTAC, DACAR 535, to Rosenberger
7-141702731-036
The density/ thickness of DACAR 535 wire may require a module loading pattern that includes extra slot spacing to prevent wire bend and pressure. See the VTAC User Manual for more information.
-
product
Waveguide Directional Couplers
WR-42 to WR-10 waveguide sizes. Split block waveguide versions available. Available in 7 bands including K, Ka, Q, U, V, E, W from 18 GHz to 110 GHz. 30 dB typical directivity. E Bend and H Bend configurations available. 10 dB and 20 dB coupling values are offered.
-
product
Standard VXI Module Shield Kits With Address Switch Opening
* Single-slot kit fits all VXI-1 Revision 1.0 to Revision 3.0 chassis.* Clamshell design fits C-size modules with 96-pin connectors.* Side shields include connector shrouds for maximum shielding.* RFI limiting, air vent slots along top and bottom edges for good air circulation thru the module.* Extruded front panel is bend resistant.* Address switch opening on component side shield.* Complimentary layout support includes PCB design template and CAD layout files.
-
product
VTAC Patchcord, Receiver, 72", VTAC, 2x 1000Base-T1 UTP wire H-MTD Cable Jack, 1 Slot
7-142716765-072
VTAC Patchcord, Receiver, 72", VTAC, 2x 1000Base-T1 UTP wire H-MTD Cable Jack, 1 Slot.Note: Static Bend Radius - 19.2mm [.76in], Flex Bend Radius - 48mm [1.89in]
-
product
Edge Press Technology Bed of Nails Testers
Protector Edge Press Family
Designed for testing heavy massive boards. Boards with heavy components like large transformers and inductors can destroy normal test fixtures. This design utilizes a 3 plate system where an internal lever actuated sub plate containing the test pins raises to probe the circuit board when the handle is pulled. Heavy boards can bend and break exposed test pins. Similarly large boards which need to be probed by very small delicate test pins can also benefit from this protected test fixture design. This fixture is recommended in situations where there is a high board mass to pin size ratio and pin protection is required. Front and rear panel modular inserts allow for easy updates and customizations to the user hardware interface.
-
product
ITA, ICon XL, 2 Module, Extra-Large Backshell, EMI
410123232
The iCon XL offers an extra-large u-shaped cable clamp that can hold cable bundles with an oblong bushing effective diameter of 1.95" and offers a cable bend radius of 1". A slide-off backshell allows easy access to wiring for maintenance and probing. The iCon XL also offers EMI shielding.
-
product
ITA, iCon, Extended Cable Clamp
410123115
This iCon ITA includes an extended cable clamp to accommodate larger cable bundles. The maximum cable bundle area = 1.97 " sq. or a 1.58"/40.13mm diameter bundle. The clamp may be inverted for smaller cable bundles.Please note: This ITA does not offer an increased bend radius that may occur with a larger cable bundle radius. Larger bend radius is offered by the iCon XL, p/n 410123232.
-
product
Carton Force Analyser
CFA
By measuring the stiffness of the substrate and crease bending resistance the user can optimise cartons for faster running and packaging speeds. The instrument allows individual creases to be analysed identifying problem areas in packaging design or manufacture. Industry research indicates that the packaging speeds of pre-glued skillets is governed by the energy required to open creases. The Hanatek CFA is the first instrument to isolate and accurately measure this key parameter The instrument measures: Bending resistance, bending moment, board stiffness, crease recovery stiffness, crease folding force, crease opening force.
-
product
Computer Control Tensile Testing Machine
SG-L03B
These series of universal testing machine are used to test tension, compression, bend, shearing force, adhesion, peeling force, tear strength,...etc. of specimen, semi-product and finished product in the field of rubber, plastic, metal, nylon, fabric, paper, aviation, packing, architecture, petrochemistry, electric appliance, automobile,...etc. , which are the basic facilities for input quality contorl (I.Q.C), Quality Control (Q.C.), Physical Inspection, Mechanics Research and Material.
-
product
Probes
Pro-Series®
Pro-Series High Temp Cooking Probe 6" Long probe with a right angle bend for easy pulling from meats or turkeys. Cable withstands 700°F to better withstand broiling and grilling temperatures. Probe tip and sensor read temperatures to 572°F for deep-frying. Good general-purpose probe, the length reaches the center of large roasts and turkeys.
-
product
Materials And Chemical Analysis
Anderson Materials Evaluation, Inc.
Materials characterization, failure analysis, quality control, and materials and process development services are offered. Our analytical techniques allow us to assess elemental and chemical material composition, thermal properties, coating thickness, electrochemical properties, surface chemistry, surface wetting, corrosion rates and pitting potentials, contamination and degradation problems, metallography, fractography, phase transitions, static coefficient of friction, adhesive bonding strength and causes of adhesive bonding failures, surface tension and surface energy, tensile and compressive strength, bend deflection, lapshear strength, elasticity properties, UV and visible light absorption and reflection, density and porosity, and many other material properties integral to improving your products.
-
product
EZ-Glider Articulated Torque Arms
The EZ-Glider torque arms are designed to improve production and quality control during the assembly process. With the ability to bend like an elbow, the torque arm provides agility to position the tool in a variety of positions for different applications. Arm can be set at an inclination of 0º, 22.5º & 45º. The effortless handling of the torque arm provides comfortable tool operation and increased production.
-
product
Power Cord Bending Tester
SW-6
SW-6 Power cord bending tester is fully designed according to the IEC standard, and can also be costumer-sized depends on the samples’ type and the costumer’s requirement. Specifications: • Power supply：AC220V 50/60HZ 12KVA • Control mode: PLC with touch screen and Servo motor. • Test Speed: 10~60times/min (Adjustable) • Test Degree: 0~540° (Adjustable) • Counter: 0~999999 (Can be pre-set) • Weight: 5N,10N,20N. 2Sets. (6Position type will have 6 Sets) • Position: 2/6 • Load Current: 0~20A (Adjustable) • Angle plate: Can check the test situation • Sample fixture: Can be costumer-sized. • Can do power line bending test (The User need prepare sample and power supply ), Can record the number of the sample’s work with load.
-
product
Bi-Directional-Coaxial LD/PD Module
BiDi-F1000 (FTTx)
Hangzhou Huatai Optic Tech. Co., Ltd.
*Laser optical: DFB or FP* DFB laser optical: with isolation or without isolation* Low threshold current and operating current *High output power *Built-in InGaAsP monitor PD *High responsivity, InGaAs planar PIN detector* Wide temperature range operation(Tc=-40℃to+85℃) *Fiber ITU-T G.657 Bending low loss, fiber optic cable features
-
product
Dual Parallel Strain Gauges
Dual Parallel Strain Gauges strain gauges have two measuring grids arranged parallel to each other. Typical applications include measurements on bending beams
-
product
Economical Bending Beam Load Cells
EBB SERIES
The EBB Series is a economical low capacity bending beam load cell suitable for use in a variety of industrial and OEM force measurement and weighing applications. It is made of an aluminum alloy and comes in 1, 2, 5 and 10 kilogram ranges.
-
product
Elasticity, Bend & Impact Testers
The performance of coatings when influenced by external stresses caused by stretching, bending or impact, determines their suitability for their designed application. A coating designed for use in the coil coating industry, for example, should have the ability to stretch as the substrate is formed into its desired shape without damage.
-
product
Passive Components
VDI offers a wide variety of waveguide sections, tapers, antennae, bends, and directional couplers for your application. Please note that external dimensions are subject to change.
-
product
Economical Single Point Bending Beam Load Cells
ESP SERIES
The ESP Series is a economical, high accurate single point bending beam load cell. It is ideal for OEM applications such as electronic scales and weighing machines. The single point bending beam design is highly resistant to eccentric loading allowing direct mounting to the scale base and weighing platform. The ESP Series features a moisture proof sealant.
-
product
Cold Ross Flex Tester
UI-FT27B
Cold Ross Flex Tester – Ross Flex Machine is used to test the cut growth in rubber vulcanizates under continuously bend flexing in 90° in low temperature chamber. Ross Flex Test Method includes ASTM D1052, SATRA TM60, ISO 4643 and etc. Ross flex machine is one of the most common sole testing machines in footwear testing Lab.
-
product
Bending Test Machines
Infinity Machine International Inc.
Bending Test Machines by Infinity Machine International Inc. - for applications such as bending cycle test machine wire wing left and right tester, 90° 180° bending wire swing test left and right optical cable repeated bend testing machine, cable bending durability tester, cable flex bending test machine, high precision bending test machines, and more.
-
product
Compact Electro-hydraulic Servo Universal Testing Machine
HLC series
Jinan Testing Equipment IE Corporation
HLC series single space Servo-Hydraulic UTM of Compact Type is designed for low capacity test. The single space compact type hydraulic universal testing system has rigid and compact design for testing the tensile, compression, bending, shearing and hardness of metal and non-metallic materials. Configured with extensive range of accessories for various applications, the hydraulic universal testing machine can provide the optimal testing solutions for your individual application needs. The single space Servo-Hydraulic UTM of Compact Type is easy to operate and is versatile in the applications of metallurgy manufacturers such as steel mills & alloy, reinforced bar, aircraft industry, research institutes, laboratories, calibration institutes etc.
-
product
Bending Beam Load Cell
EST-7
Technopark Automation & Control
The EST-7 is a Bending Beam Load Cell suitable for use on lower capacity weigh hoppers, filling machines, packaging machines and conveyor belt scales. This load cell is available in capacities from 10 kg to 200 kg.
-
product
Large testing machine for timber
This device is used to conduct a three- / four-point bending test on wooden pillars. To facilitate the adjustment between the bearings, it is equipped with rails on the base as well as a trolley to transport the sample.
-
product
Pure Bending Fatigue Teesting System
PQ-6
Jinan Testing Equipment IE Corporation
PQ-6 Pure Bending Fatigue Testing Machine is suitable for testing the fatigue strength of metals and other materials under bending & rotating.
-
product
Single Screw Electromechanical Universal Testing Machine
CMT Series
Jinan Testing Equipment IE Corporation
The CMT series single screw testing machine is designed for mechanical property test mainly on metal materials, cement, asphalt, and bitumen etc. A variety of fixtures can be offered to do compression, bending and shearing test as well. This series of single screw testing machine is suitable for the applications in quality inspection, research, metallurgy, rubber & plastics, and knitting materials, and widely used in many fields such as industry factories, mineral enterprise and high schools.
-
product
Smart Optical Time Domain Reflectometer OTDR
BD900 Series
Shanghai Baudcom Communication Device Co.,Ltd.
BD900 series of Optical Time Domain Reflectometer has excellent dead zone performance and wide dynamic range. There are four models to choose from and that can betterly meet the customer’s specific measurement requirements. Combined with the visual fault locator, it can easily find the breaks, bends, splices, faulty connectors, and other causes of signal loss.
-
product
Deflection Gauge Extensometers
We supply a wide range of deflection gauge extensometers ideal for measuring deformation in three and four point bend tests and in compression testing applications.
-
product
Fiber Stiffness Tester
DRK023B
Shandong Drick Instruments Co., Ltd.
Used to determine the bending properties of various fibers.
