Product

Operational Amplifiers

-

ams-OSRAM AG

ams-OSRAM AG

Operational amplifiers from ams are ideally suited to audio applications. These CMOS devices are available as single, quad or differential amps. They feature good common-mode rejection, have low input bias currents, good gain bandwidth, low total harmonic distortion and an excellent rail-to-rail output-drive capability of 200mA peak.

Product

Impulse Semiconductor High Current Integrated

Transmission Line Pulse Test System

-

Impulse Semiconductor Inc.

Transmission Line Pulse Test System - Impulse Semiconductor Inc.

The Impulse Semiconductor High Current Transmission Line Pulse (TLP) test system is the tool of choice for extracting ESD parameters for transient protection devices in a package, or at wafer level. With accuracy better than 100 milliohms at 40 amps peak current, the Impulse high current TLP is specially tailored to the needs of today's ESD device designers who must accurately measure low values dynamic resistance irrespective of breakdown voltage.

Product

Surge Power (Joule Rating 342) (10) 5-20R 0U V/H

EPSS-1020-HV

-

ELMA Electronic, Inc.

EPSS-1020-HV - ELMA Electronic, Inc.

EPSU Power (Basic / Surge / Metered / Value) – rack mountable power distribution, 120V, optional surge suppression, and amp meter

Product

Artificial Phantom Load with Power Factor

RC-50

-

TESCO

RC-50 - TESCO

The RC-50 Artificial Phantom Load has been re-designed to meet the most exacting requirements. It operates from a single phase source and will deliver current at either unity or 50% power factor at all full load ranges. Features: Artificial Load, Light Weight, 50 Amps, 50% Power Factor.

Product

Laser Diode Testing

-

Yelo Ltd.

Yelo Ltd.

The low power series of burn-in and life test systems are designed to test the reliability of low power laser diodes up to 1 Amp in current. The modular design means they can test up to 2,048 lasers, however due to the flexibility of the system, it can be adapted to suit both low volume R&D environments and high volume production environments.

Product

DC Electronic Load

EE15140A

-

Executive Engineering

EE15140A - Executive Engineering

The EE15140A DC Electronic Load /  Works @ 0.0 Volts Input & real time I/O control  attach the electronic load block to a heat- sink and your up and running. used them with D to A's, A to D's, Pots, PLC's to control the current. These Electronic Loads can be used for both Discharge & Charging Batteries & Devices

Product

CPCI BUS Interface Card

Cpci301 MIL-STD-1553

-

Andor Design Corp.

Cpci301 MIL-STD-1553 - Andor Design Corp.

MIL-STD-1553 A, B & McAir MULTI PROTOCOLS Simulator / Analyzer / Tester CPCI BUS Interface Card - The CPCI301 can be used for Validation Testing, Production Testing, full bus simulation and monitoring, as a general purpose 1553 interface or a stand alone bus Analyzer. For precise message scheduling and measurements, the Major and minor frame times are independent of message sequences or retransmissions on errors and the start of all command messages are independent of message length, response time or length of response. Message timing is calibrated and RT responses have low jitter.

Product

Portable Circuit Breaker Tester

PI-1600

-

ETI Precision

PI-1600 - ETI Precision

The PI-1600 Circuit Breaker Tester incorporates modular design and flexibility to provide unequaled capability in a portable package. The PI-1600 test set is two testers in one, incorporating the PI-800 and PI-AUX. The PI-800 section can be used alone, on 120 or 240 VAC supplies, generating continuous current of 400, 800, amps at 4.2 kVA, with peak output to over 10x. When configured for the PI-1600, the PI-AUX output unit is connected in series or parallel to the PI-800. The PI-AUX boosts total power to 9.8KVA, and allows testing of draw-out breakers and MCB’s to 1600 Amps. The units are housed in rugged interlocking suitcase-size enclosures. Each piece weighs no more than 125 pounds, allowing one-person hand truck mobility. Basic operation is very simple, and the proven MAC-21 control instrumentation provides optimal output control and measurement. The MAC-21 instrumentation is supplied in a separate rugged portable case, interlocks on top of the PI-800, and connects to a cable in the rear of the test set.

Product

Data Logging System

Motor101A

-

MadgeTech, Inc

Motor101A - MadgeTech, Inc

The Motor101A measures and records on and off status changes for motors or other equipment drawing up to 200 Amps. The state change occurs when the current switch exceeds the 150mA set point. This allows for most basic equipment to be monitored.