PCB Adapters
-
product
37-Pin D-Type Male Straight PCB HV
40-963-037-SM-HV
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires. 37-Pin Female connectors can be directly mated to a corresponding Pickering Switching Module while Male versions can be used to interface to a Female cable assembly termination.
-
product
50-Pin Ribbon Conn Straight PCB Mount
40-963-550-SM
Ideal for user created termination schemes where the termination is to be remotely connected to the module by cable. Interfacing PCBs should be designed with suitable clearances for the working voltage the application requires.
-
product
Automatic Double-Sided Bare PCB Final Inspection AVI System
FI-18 Series
InScan Limited (SIP) Co., Ltd.
InScan FI-18 is a compact and high performance fully automatic double sided AVI system for Final Inspection of PCB boards.The setup is based on golden board and CAD data which greatly simplifies the setup process. The FI-18 series inspects and processes a double sided board sized 210X300 mm 5.5 sec. Superior interline high resolution CCD sensor.
-
product
Adapter for 980L-1A Tester
TA-331A
331A-9G HSI Adapter for use with the 980L-1A tester. Built to manufacturer's specs to allow by the book testing.
-
product
PCB IMIC01, 100 mV/g, 2-Pin, Accelerometer, Industrial Vibration Sensor
780985-01
The PCB IMIC01 is an industrial Vibration Sensor designed for permanent installations. This sensor helps you acquire sound and movement data with supported PXI Sound and Vibration Modules, C Series Sound and Vibration Input Modules, and USB-based Sound and Vibration Devices. The PCB IMIC01 features a sensitivity range of 100 mV/g and uses the Integrated Electronics Piezo-Electric (IEPE) current excitation. The sensor supports the IMI Industrial Accelerometer Cable as well as the MIL2M-Breakout Cable.
-
product
Adapter, 2.4 mm (m) to 3.5 mm (m), DC to 26.5 GHz
11901A
The Keysight 11901A is a 2.4 mm male to 3.5 mm male metrology-grade adapter with dc to 26.5 GHz operation.
-
product
Test Port Adapter Set, 3.5 Mm (Test Port) To Type-N
85130C
The Keysight 85130C test port adapter is designed to protect the test set port when it would be directly connected to the device under test. These adapters have a special rugged female connector designed for connecting to the network analyzer test port. This special connector will not mate with a standard male connector, but converts the rugged test set port to a connection that can be mated with the device under test. The set contains a 3.5 mm to type-N male adapter and a 3.5 mm to type-N female adapter. The frequency range for these adapters is dc to 18 GHz with a return loss of 28 dB or better.
-
product
PCIe High Performance Host Adapter: Dual Port (x16), Gen 3
M9049A
The M9049A is a PCIe interface card for computers with PCIe expansion slots. It provides an extremely high performance link from an external computer to an AXIe or PXIe Chassis. The M9049A has a flexible configuration capability. Each card has two Gen 3 x8 PCIe cable links capable of achieving speeds up to 8 GB/s on each port. These two ports can be combined into a single x16 cable link providing a speed of up to 16 GB/s. This means a data-intensive system can be built using high-performance desktop or rack-mounted computers.
-
product
Adaptable Tactical Data Link Router
Curtiss-Wright Defense Solutions
Curtiss-Wright’s TCG ATR occupies a singular position in the market to guarantee seamless connectivity of multiple Link 16 network interfaces while maintaining a highly scalable hardware design and affordable price.
-
-
product
37-Pin D-Type Male Straight PCB Mount
40-963-037-SM
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires. 37-Pin Female connectors can be directly mated to a corresponding Pickering Switching Module while Male versions can be used to interface to a Female cable assembly termination.
-
product
Adapters & Converters
Using our prebuilt, off-the-shelf standard adapters, custom converters, or custom adapters, incorporate performance and process data from across your enterprise, without having to disrupt your manufacturing line or change the outputs or your manufacturing process.
-
product
Adapter, 1.0 mm (m) to 2.4 mm (m), DC to 50 GHz
11922A
The Keysight 11922A precision 2.4 millimeter coax in adapter offers a simple way of measuring coaxial devices at higher frequencies. It is designed for the measurement of components with 50 ohms impedance and a frequency range from dc to 50 GHz.
-
product
Test Adapter
cPCI/VME/VME64x
The test adapter is used for measurement and testing of test specimen boards, which gives optimal access of signals, address lines as well as power from backplane assembly. Usually the test adapter includes fields for voltage and amp, current measurements and in some cases also some pins for wire wrap to conduct custom connections.
-
-
product
160-Pin DIN41612 Connector, Right Angle PCB Mount, Female
40-963-160-RF
Accessory allows a user to create their own PCB based termination solution. Female versions are suited to direct connection to a Pickering Switching Module while male versions can be used to interface to a female cable assembly termination.
-
product
Passive XMC-to-PCI Express Adapter
6067
The Technobox, Inc. P/N 6067 is designed to adapt a single-wide XMC card to a 1X PCI Express slot. The 6067 supports P15 only and allows access to PN4 signal via the adapter's DIN connector. The A and C rows of a 96-pin DIN connector connect with the 64-pin user I/O connector (J4/P4) on the mezzanine card, permitting internal connection of rear I/O. JTAG signals are brought out to headers allowing users the option of connecting the two JTAG ports.
-
product
PNMDF3.5F NMD 3.5mm F to 3.5mm F Adapter
PNMDF3.5F Adapter, NMD 3.5mm F to 3.5mm F, Frequency ,Range: up to 26.5 GHz, Impedance: 50 Ohm
-
product
Adapter Plate, 9050 Enclosure to 9025 ITA
410112772
Adapter Plate, 9050 Enclosure to 9025 ITA (ITA Positioned on Upper Part of L-Shaped Enclosure)
-
product
32/64-Bit 33/66 MHz PCI-X-to-PMC-X Adapter
4068
The Technobox, Inc. P/N 4068 PCI-X-to-PMC-X Adapter permits operation of a standard 32- or 64-bit PCI-X card in a PMC-X slot. It provides a migration path for PCI-X board suppliers to port their products to a PMC-X form factor. As the PMCX equivalent board is developed, software development and migration can proceed with the original PCI-X board operating in a PMC-X environment.
-
product
Vacuum Test Adapter
Vacuum test adapters (VA) are suitable for contacting electronic assemblies with large quantities (mass testing) and a small number of variants. INGUN vacuum test adapters are available as standard as a single system without an exchangeable replacement kit.
-
product
NM-SF 50 N-Male to SMA-Female Adapter
NM-SF 50 Adapter, N-Male to SMA-Female, Frequency Range: DC to 18 GHz, Impedance: 50 Ohm
-
product
Piranha USB-FXS Adapter
SKU-083-01
The Piranha USB-FXS Adapter is the second product in the Piranha USB Adapter™ family. This device simplifies and makes a cost-effective analog phone connection for a telecommunication system. Our design is ultra-compact – this USB-FXS adapter is designed to be a part of the actual cable between your analog phone and your system’s USB port.
-
product
Carrier Cards and Bus Adapters
Abaco's wide range of carrier cards allows you to expand your systems capabilities simply and cost-effectively, allowing easier technology insertion.
-
product
Adapter, 1.0 mm (f) to 1.0 mm (f), DC to 110 GHz
11920B
The Keysight 11920B precision 1.0 millimeter waveguide-to-coax adapter offers a simple way of measuring coaxial devices at higher frequencies. It is designed for the measurement of components with 50 ohms and frequency range from dc to 110 GHz.
-
-
product
Single Front Slot Universal Low-Profile PCI To PCMCIA Adapter, External
P314B
To cater to the latest generation of low-profile PCs that can only use low-profile PCI add-in boards, Elan has created the P314. This model, from the P-Series range, features a PCMCIA Type III 3.5" drive bay mounted slot and a circuit board that conforms to the MD1 profile specification. It will allow you to use any TypeI/II/III PCMCIA card.
-
product
PCB Test Connectors
Tag-Connect
Tag-Connect is a simple and secure way of connecting debuggers, programmers and test equipment to your PCBs. Tag-Connect uses a specially designed and patented connector for making the connection to your PCB (Patent Pending for the -NL versions). Tag-Connect eliminates the need for a programming or JTAG connector on your PCB.
-
-
product
Y Lead Adapter for ZD Differential Probes Qty 1
PACC-ZD001
Y lead Adapter for ZD differential probes Qty 1
