Cables
See Also: Cable Assemblies, Cable
-
Product
Cable Assembly, Receiver, 20", Tripaddle, 96 Pin 2X InfiniBand SMB
540285010103
Cable Assembly
Cable Assembly, Receiver, 20", Tripaddle, 96 Pin 2X InfiniBand SMB.
-
Product
WAVEPULSER-40IX + WAVEPULSER-SI-STUDIO-NRZ + Adaptors and Calibration Kit
WAVEPULSER-40iX-BUNDLE
-
High-speed Interconnect Analyzer, 4-port, S-par @40 GHz, <1 mm Res., 4 phase matched cables, bundle.
-
Product
Door Contact Sensor
ENVIROMUX-M-DCS
-
Monitors access with a magnetic bridge sensor, which responds to any magnetic material (no special inserts necessary). Can also be used for monitoring side wall and covers. Includes mounting hardware. For normally closed circuit connection. 2-wire interface. Screw terminal. Maximum cable length: 1,000 ft. Wide actuating gap, approximately 1". Dimensions WxDxH (in): 0.5x0.5x2 (Switch), 0.5x0.5x2 (Magnet). Operating temperature: 32 to 158°F (0 to 70°C). Regulatory approvals: RoHS.
-
Product
Piezo Velocity Sensor
VE102
-
Piezo Velocity Sensor, Side Exit Connector / Cable, 100 mV/in/sec
-
Product
Net Toner and Probe Kit
1EA680
-
Cable tracer is designed to trace wires without damaging the instalations and much more.
-
Product
1.5 M 50-pin D-Sub Cable
Y1135A
Switch Cable
Connect this M/F twisted pair with outer shield cable to 34980A multifunction switch/measure mainframe and modules
-
Product
FieldFox Handheld Analyzer Software
-
FieldFox can be configured as a cable and antenna analyzer, vector network analyzer, spectrum analyzer, built-in power meter and much more using software/firmware functionality. All functions listed on this page can be installed at the time of FieldFox purchase or can be upgrade via a software license key. Select the functionality you need today and add more features as your needs change.
-
Product
18" Ribbon Cable
CONM50-D25-1
-
An 18" ribbon cable transitions from individual IP Module ribbon connectors on the ISA (PC/AT) carrier board to a 25 pin female D-sub connector mounted on a PC expansion card end-panel.
-
Product
Connector, PCB Mount, 25 Pin 1.27mm Pitch Micro-D, Male, Right Angle
C025CMX-1PR-0A
-
This 25 pin micro-D right angled connector is designed to allow users to create their own PCB based connection solution. Screwlocks are provided to secure the connector to its associated cable assembly. This connector is suitable for high density applications including connection to Pickering's LXI DIO/Trigger port via a suitable cable.
-
Product
Low Inductance BNC Cable, VOLT:DC 60V
PX0105A
Coaxial Cable
The Keysight PX0105A is suitable for narrow current pulse measurement down to 10 μs pulse width. It supports the Keysight M9602/03A.
-
Product
Power And Data Transfer
-
Cable reels & slip ring assemblies for reliable power and data transfer in mining, construction and material handling applications.
-
Product
Optical Fiber Identifier
FID-30R/ 31R
-
Shanghai Fibretool Technology Co.,Ltd.
FID-30R and FID-31R are optical fiber identifier for telecommunication cable. FID-30R is built-in optical power meter.
-
Product
Self-Adhesive Clips for Liquid/Chemical Sensor Rope
ENVIROMUX-CLP10-LD
-
Use to prevent sensor rope cable from shifting after installation. Self-adhesive backing for easy installation. Material: Nylon. Quantity: 10 clips. Compatible with ENVIROMUX-LDSx-y, ENVIROMUX-CDSx-y, ENVIROMUX-LDx-y and ENVIROMUX-CDx-y.
-
Product
Cable Fault Locator ECFL 30
ECFL 30
-
Compact precision active/passive, AC/DC bridge with dual channelTDR for fault location on balanced loaded and unloaded cables.
-
Product
Clamp type AC Current Sensor／for Load Current Measurements(CT Series)
CT-80
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Big CT window*AC 1A～1800A*Current measurements of main cable
-
Product
Training/Verification/Demonstration Fixture | CableEye Cable Harness Tester
Item 802 (CB-T2)
-
This multi-purpose CBT2 fixture can be used for operator training, tester system verification, and facility verification.
-
Product
Bias Tees
-
Bias Tee for remote power supply of preamplifiers and converters via the coaxial cable.
-
Product
2.4 NMD Female and 2.4 mm Male Test Cable
C5024NMDF24M
-
Our 2.4 mm test cable is made to ideally suit our larger line of vector network analyzers. The C5024NMDF24M test cable operates at a frequency of 50 GHz and is compatible with our USB vector network analyzers.
-
Product
SD Express
-
SCHILLER AUTOMATION GmbH & Co. KG
The Standard SD Express Memory Card Test Adapters support PCIe® 16 GT/s (Gen4) and PCIe® 8 GT/s (Gen3) Interface Compliance Program testing for SD8.0 and SD7.1. Minimal crosstalk, short trace lengths. The Micro SD Express Memory Card Test Adapters supports PCIe® 8 GT/s (Gen3) Interface Compliance Program testing for SD7.1. Minimal crosstalk, short trace lengths. They all support SDHC, SDXC, and SDUC operation modes Data collection via Lab Standard SSMP Test Cables and hard gold mating surface allow for high cycle count insertions and reliable performance.
-
Product
Cable Tracers
180 CB
-
Standard Electric Works Co., Ltd
● The Amplifier Probe is designed to identify and trace wires or cables within a group without damaging the insulation.● Works with any Tone Generator to identify wires.● Volume control for increased sensitivity and adjustable to suit work environment.● Recessed ON/OFF button prevents battery drain.● A phone jack is designed for headset or handset.
-
Product
DC Meters/Rail Meters:
-
Digital DC Resistive Voltmeter has a single range of 0 – 2kV. The unit consists of a meter probe, second probe, and connector cable. This unit is designed to measure DC voltage between the negative return rail and overhead positive cantenary conductor used on transit systems. The five position selector switch located on the face, controls OFF, ON, and Test. The OFF positions are for storage and transit. The ON position is for measurements from 0 to 1999 volts with one-volt resolution. The T position tests basic meter functions and the digital display.
-
Product
Cable Assembly 44-Pin D-Type Male to Unterminated With Cut Ends, 1m
A044HM5-C-0A100
Cable Assembly
The 44-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 7/0.15 (26AWG) Silver Plated Copper Wire. The connector can be secured to the product by screwlocks.
-
Product
Semi-Rigid Test Probes Up to 6 GHz
-
Fairview Microwave’s semi-rigid test probe assemblies come in multiple cable diameters to help when attaching the unterminated end of the probe to a circuit board trace. There are two versions including straight-cut probe ends for those that would like to customize the dimensions of the center conductor and dielectric dimensions, as well as pre-stripped probe ends that are ready for immediate use. By soldering the outer conductor to the signal ground and the exposed center conductor to the trace carrying the signal of interest, simple sampling measurements can be made without having to create a separate subassembly circuit board or add a connector to the circuit layout which can take up valuable real estate. Fairview provides 3 diameters of semi-rigid coax and 3 different lengths from 3 inches to 12 inches to fit a variety of trace widths and applications. All test probes are 100% RF tested to ensure the cable assemblies operate to 6 GHz and also to make sure that the SMA connector interface meets the 1.35:1 VSWR specification prior to shipping. To protect the small diameter coax from damage, each part is shipped in a clear protective tube that can also be used for storing the probes for future use.
-
Product
Midwave Infrared Thermal Camera
FLIR A6780 MWIR
-
The FLIR A6780 MWIR camera system makes it easy to measure temperatures of rapid thermal events and fast-moving targets, making it an ideal choice for industrial, military, and manufacturing R&D applications. This affordable, cooled InSb camera offers the flexibility of both manual and remote-focus lens options to maximize the number of measurement pixels on the object of interest. And single cable connectivity using Gigabit Ethernet provides complete camera control plus data capturing in FLIR Research Studio software – so users can analyze and understand data faster than ever before.
-
Product
Cable Assembly 44-Pin D-Type Male to Unterminated With Ferrules, 1m
40-972-044-1m-MU
Cable Assembly
The 44-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 7/0.15 (26AWG) Silver Plated Copper Wire. The connector can be secured to the product by screwlocks.
-
Product
Probes
Pro-Series®
-
Pro-Series High Temp Cooking Probe 6" Long probe with a right angle bend for easy pulling from meats or turkeys. Cable withstands 700°F to better withstand broiling and grilling temperatures. Probe tip and sensor read temperatures to 572°F for deep-frying. Good general-purpose probe, the length reaches the center of large roasts and turkeys.
-
Product
RF Spectrum Power Meter
SPM-50
-
SPM-50A Spectrum Power Meter brings innovative testing concept and approach for RF cable system installation and maintenance. It combines the key function of spectrum analyzer and power meter, designed to measure the power characteristics of particular signal among mixed signals transmitted on cable, fast and accurately present result in power histogram or spectrum chart.
-
Product
Cable 100-Pin Micro-D Male to Unterminated, Cut Ends, 1m 2-56 UNC Screwlocks, Metal Shell
A100SMR-C-9A100
Cable Assembly
This 1m long male to unterminated 100-Pin SCSI Style Micro-D Cable Assembly is suited for direct connection to various products using the 100-Pin connector. It is constructed from 100-Pin twisted pair cable with varying left and right hand lays to minimise crosstalk. The Cable is colour coded to ensure easy connection. Screwlocks are provided to secure the SCSI connector to its associated product.
-
-
Product
Cable Assy 25-Pin D-Type M/M 2m
40-970-025-2m-MM
Cable Assembly
The 25-Pin D-Type cable assembly is constructed from 19/0.18 (21AWG) Tinned Copper Wire with PFA insulation. Screwlocks are provided to secure the connectors to their associated products. The 25-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
