-
product
Chip Resistor Networks/Arrays
Panasonic Industrial Devices Sales Company of America
Panasonic’s Chip Resistor Arrays are offered in cases from 0201 to 0805. The smaller 0201 case sizes are available with flat terminations and all other case sizes are offered with either convex or concave terminations. The EXB Series Resistor Arrays are available in 2, 4, or 8 Resistors per package. These Resistor Arrays allow for an improvement of the placement efficiency. Compliance Standards include: IEC 60115-9, JIS C 5201-9, EIAJ RC-2129, AEC-Q200 and RoHS.Panasonic’s Resistor Networks are available in 8 or 15 bussed Resistors and are recommended for all pull up/down circuits.
-
product
Signature Compression Only Load Button Load Cells
SLB SERIES
The SLB Series Subminiature load cells (Load Buttons) are offered for compression only applications where space is limited. The matching surface must be flat for ultimate accuracy. The loading diameter is slightly convex for accurate load distribution. These sensors are manufactured from heat treated 17-4ph stainless steel, and the sensing element incorporates bonded foil strain gages of the highest quality. They are sealed for protection against most industrial environments.
-
product
Power Amplifiers
WBPA Series
Besides offering wide bandwidth, WBPA series wide band power amplifiers have exceptional gain flatness and ultra high linearity. The IP3 are from 40 dBm to over 50 dBm. The different models cover the frequency bands of VHF, UHF, Celular, GPS, DCS, PCS, 3G, MMDS, and S band. The amplifiers have optimum return losses, gain flatness, high power and high added power efficiency, wide bandwidth matchings, and unconditional stability.
-
product
Low Noise Amplifier
Low noise amplifiers, or LNAs, are designed and manufactured by utilizing the most advanced PHEMT or MMIC devices, thin film technologies, and an improved DC power supply to deliver a low noise performance with broad operating bandwidths and good gain flatness. While standard models focus on general purpose applications, additional models with differing frequency ranges, gains and noise figures are listed on the website. Custom designs are also offered to meet any user’s specific needs.
-
product
Multi-Channel Attenuation Control Unit (4-channels), DC to 6 GHz, 0 to 121 dB, 1 dB Step
J7204A
The J7204A is a multi-channel (4-channels) attenuation solution for signal attenuation and conditioning of up to 4 devices under test (DUT). Operating frequency from DC to 6 GHz, with 121 dB, 1 dB steps. Exceptional 0.03 dB insertion loss repeatability per section for the entire 5 million cycles and excellent attenuation accuracy and flatness, the J7204A reduces cost of ownership and provide the best measurement accuracy.
-
product
Luminance Colorimeter
RayClouds Photoelectric Technology Co.,Ltd.
Measurement parameters: luminance, chrominance, color temperature, flicker, Gamma, etc.Applications: mobile phone screens, small flat panel displays, TV displays, etc.
-
product
7-WAY Blade & 4 Flat Connector Tester
3536B
Peaceful Thriving Enterprise Co Ltd
This is a tester to test the function of the 7 way connector of the vehicle. User simply plug the tester with the 7 way or 4 way connector, and switch on the corresponding function of the vehicle to check if the LED indication has lighted up correctly. Use in the garages, workshops where there is a need to check the configuration of circuit. Widely used to test trailer light circuits on most trucks, boats, trailer campers, caravans, food trucks and other trailers.
-
product
Optics Test Equipment + Flatness, Bow, Warp, Curvature, Glass Thickness
Wedge Angle Scanner For Car Windshields
Optik Elektronik Gerätetechnik GmbH
Scanning of complete car windshields for measurement of wedge angle and thickness distribution, in particular in the HUD area.
-
product
Pattern Converter for WGL/STIL to ATE
VectorPort
VectorPort is a versatile, low-cost test development tool for converting WGL or STIL vectors to targeted ATE tester formats, including pattern, timing, and pinmap data. VectorPort can read and write all major formats in both parallel (Flat) vectors and serial (SCAN) vectors.
-
product
LED Type Wafer Alignment Sensor Controller
HD-T1
Panasonic Industrial Devices Sales Company of America
The HD-T1 Series is a new Wafer Alignment Sensor that uses a safe red LED light beam, with a resolution of 30µm, to achieve the same high level performance as Laser Sensors. The HD-T1 Sensor is best suited to detect wafer eccentricity, notches and orientation flats. Using linear image Sensor methodology and high-speed sampling technology, a wide variety of objects can now be stably measured with great precision at ultra-high speeds. This CCD style Sensor is developed for use in almost all fields of industry, e.g. tire manufacturing or Semiconductor production (Wafer Printed Circuit Boards).
-
product
Shielded and Unshielded Cable
Teledyne Marine Cable Solutions
Shielding Types• Braided I Served I Spiral• Foil & Hybrid• Vapor Barriers• Copper & Alloys• Conductive & Static Dissipative Tapes• Conductive Fabrics• Tensile Members• RFI & EMI Tapes & Braids (Serveor Interwoven)• Utilizing Flat & Round Copper• Stainless Steel• Bronze• Aramid Fibers & Textile, amongothersConstruction• Multi-conductor, shielded pairs, pairs with steel tubed fiber or copper conductors with fiber optics, coaxial conductors & aramid strength fibers
-
product
Double Flat Venturi
4129D
Parker Conflow's double flat Venturi provides high directional air movement for cutting machines in mining for larger dust suppression and ventilation requirements
-
product
Optical Transmitter
ST1013-10mW
Hangzhou Softel Optic Co., Ltd.
*Designed for FTTH(Fiber To The Home)Networks *Excellent Linearity and flatness *Single-mode fiber high return loss *Using GaAs amplifier active devices *Ultra low noise technology *Using DFB coaxial small package laser *Smaller size and easier install *Red-LED for power indication
-
product
(70×90×15mm) C-Band DWDM FGA Full Function Module Fixed Gain EDFA Module
FGA4400-FM02
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai FGA4400-FM02 series is a fixed gain Full Functional EDFA module which is specifically designed for C-Band DWDM optic transmission system, accord with various communication technology requirements of 44 channels DWDM system. It adopts nowadays excellent optical performance, advanced electronic control technology and complete software functionalities. Excellent total integration electronic transient control technology ensures amplifier to achieve the locking of optimal flat gain (OFG) in large dynamic input optical power range.
-
product
pH Pocket Water Quality Meter
LAQUAtwin pH-22
The only pocket meter that directly measures pH in 0.1ml sample (or 0.05ml sample with sampling sheet B). Unique sensor allows measurement of viscous liquids, solids, and even powder samples. No need for a beaker to calibrate your meter or measure a sample. Just place few drops of the standard or sample onto the flat sensor. This procedure saves you time and prevents wasting your precious sample.
-
product
Device Cloud for Web & Mobile App Testing
Remote Testkit
*Better test efficiency and productivity.*Flat rate for 24/7/365 unlimited device access.*Stable and secure operation by NTT
-
product
Deep Cooled UV-VIS/NIR Scientific Cameras
TE and cryogenically cooled CCD and EMCCD scientific cameras for ultra sensitivity from 200 nm to 1100 nmHORIBA Scientific offers a complete line of spectroscopic multi-channel detectors for scientific research. For spectral detection from UV to near-IR, two dimensional CCDs and indium gallium arsenide linear arrays offer a faster acquisition option over single point detectors with relatively high sensitivity. Coupled with HORIBA’s range of aberration corrected, flat field imaging spectrographs, custom spectroscopy packages can be assembled for a variety of applications.
-
product
Solvent Resistance Tester
NRJ-100
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.4-2008/IEC60851-4; Inspection standard: JB/T4279.10-2008Used to detect the solvent resistance performance of enameled round wires and flat wires with nominal conductor diameter above 0.250mm;Application of SCM control allows for fast operation and strong anti-interference capacity;Pencil push unit would automatically lay down pencil and move ahead, lift pencil and automatically return to initial position;Used in combination with JRK-60 solvent thermostatic controller;Automatic pencil sharper can sharpen pencil tip to be 60° symmetrical to its axis;
-
product
Fixed Attenuators
Macom Technology Solutions Holdings Inc.
MACOM offers fixed attenuator bare die to be used in chip and wire assemblies. These products offer excellent return loss and flat attenuation from DC to 50 GHz. Attenuation values range from 0 to 20 dB.
-
product
Fixture Kit
MF300
Due to careful selection of materials, use of modern manufacturing techniques, and supplying the kit "flat packed" for end-user assembly, Merifix fixtures kits are inexpensive enough to be used in low-volume production and in engineering labs for programming and debug tasks, where traditional fixtures would be too expensive.
-
product
RC68-68, Ribbon Cable, 68 D-Type to 68 VHDCI Offset, .25 Meter
187252-0R25
68-Pin Female to 68-Pin Female, 1 Ribbon Connection Ribbon Cable - The R68F-68F Cable, sometimes referred to as the R68-68 or RC68-68, is a flat ribbon cable that connects to 68-pin NI data acquisition or digital I/O devices. The R68F-68F Cable is offered in different lengths and with D-SUB or VHDCI front end connectors.
-
product
Fan Cooled Thermal Power/Energy Laser Measurement Sensor
F50A-BB-18
The F50A-BB-18 is a general purpose fan cooled thermal power/energy laser measurement sensor with a 17.5mm aperture. It can measure power from 10mW to 50W and energy from 6mJ to 50J. It has the spectrally flat broadband coating and covers the spectral range from 0.19 to 20µm. The sensor comes with a standard 1.5 meter cable for connecting to a meter or PC interface.
-
product
Global Standard Model For 4 Point Probe Sheet Resistance Automatic Measurement System
RT-3000/RG-1000F
*Fully automatic system for large sizes of flat panel with glass loading robot*Tester self-test function, Measurement position correction function, wide measurement range*Min. 0.1 mm meas. resolution and user programmable test pattern*Host (CIM) communication and 2-D/3-D Mapping software
-
product
pH Pocket Water Quality Meter
LAQUAtwin pH-33
The only pocket meter that directly measures pH in 0.1ml sample (or 0.05ml sample with sampling sheet B). Unique sensor allows measurement of viscous liquids, solids, and even powder samples. No need for a beaker to calibrate your meter or measure a sample. Just place few drops of the standard or sample onto the flat sensor. This procedure saves you time and prevents wasting your precious sample.
-
product
Drop Tester
AccuDrop 125
Model AD-125 is 1 of 3 models in the ACCUDROPTM Series. It helps determine the ruggedness of packagesand the effectiveness of their interior cushioning when exposed to impact during material handling. Theeffects of dropping are easily duplicated in your laboratory using the controlled and precise flat, corner, andedge drop tests.
-
product
General Purpose Low Profile
Our low profile load cells feature an advanced structural design that makes them extremely durable, accurate, and resistant to large extraneous shear and moment loads. To perform in a linear and predictable manner, the outside diameter of the load cell must be bolted to a flat rigid surface. When this is unavailable, our factory installed base provides a convenient threaded attachment point for easy installation and use in both tension and compression. All low profile load cells are stocked with the mounting base installed, but we can remove the base upon request.
-
product
High-Temperature Extensometers < 600 °C Capacitive
Instron® High-Temperature Extensometers are perfect for testing advanced composites, metals, polymers and other materials at elevated temperatures. This series incorporates a capacitive sensor that does not require any cooling. The extensometers come standard with a sensor conditioner unit providing a 0-10 V output with exceptionally low noise. These extensometers can be attached to round and flat specimens to perform tensile, compression, and cyclic tests.
-
product
Bresle Salt Meter
Elcometer 138
Incorporating a flat sensor, the Elcometer 138 Bresle Salt Meter measures the conductivity of a sample, then automatically converts this to show the density of salts, negating the need for the user to do a manual calculation when working in accordance with ISO 8502-6 or ISO 8502-9.
-
product
Large Rennie Grapnel
The Rennie Grapnel is usually used in conjuntion with the Gifford. The Rennie Grapnel is built up of flat links, the fluke passes through the body and is then welded onto it. The links are joined together in sets of four in the form of a chain, successive links and flukes being at right angles to each other. Flukes can be detached for renewal when required.
-
product
Measurement Of Straightness, Flatness, Positioning Uncertainty Of Round Tables >
ELCOWIN - Software For 2D-straightness Measurement With Electronic Autocollimators
Optik Elektronik Gerätetechnik GmbH
The software ELCOWIN serves for the measurement of straightness, squareness, parallelism of slides and flatness of precision tables by the autocollimation principle. ELCOWIN can be used in connection with electronic autocollimators of the ELCOMAT series from Moeller-Wedel-Optical.
