Power Loads
-
Product
Automated Tuners / Impedance Tuners / Load Pull Tuners
-
MT97x, MT98x and XT98x series automated tuners (also known as automated impedance tuners and automated load pull tuners) are precision instruments that are optimized for a broad class of in-fixture and on-wafer applications, and may be used in any automated or manual application requiring the ability to match the impedance of a microwave circuit element or to establish specific impedances at a terminal interface. The tuner design is based on the slide screw concept using the inherently broadband slab-line transmission structure. Each unit has two non-contacting probes deliver high VSWR with superb accuracy and reliability over a wide frequency range. These probes can be fully retracted leaving a low-loss, well-matched transmission line, which is a significant benefit in power related applications where two-port tuners capable of handling large amounts of power are required. As integral components of Maury Device Characterization Solutions, these PC-based tuners are controlled using Maury's family of Device Characterization Software tools, including MT930 IVCAD, MT993 ATS and the DLL-based measurement automation environment. Maury Microwave automed impedance tuners are ideal for load pull, harmonic load pull, active load pull, hybrid active load pull, noise figure, noise parameters and all automated tuner applications.
-
Product
SWR/ Power Meters
SX600/SX600N
-
Frequency range:1.8 to 525MHz/S1(1.8 to 160MHz), S2(140 to 525MHz). Power display range:5W 20W 200W. Accuracy at full scale:±10%. Minimum power at SWR measurement:S1(1W), S2(4W)
-
Product
PXI Load Resistor Module 10 Ohm to 2.56k
40-292-012
-
A simple solution for applications requiring a programmable load resistor with up to 15W power handling. It is able to simulate the common short circuit and open circuit conditions that can be experienced in a system due to faulty wiring or sensors.
-
Product
DC Bench Power
XPH Series
-
AMETEK Programmable Power, Inc.
The Sorensen XPH Series provides 175 to 420 watts of DC power. The XPH is a compact, high performance low cost power supply suited for benchtop applications. The Sorensen XPH Series uses combined switch–mode pre–regulation with linear post-regulation to provide performance comparable with an all linear design. The XPH features excellent line and load regulation with low noise and good transient response. The XPH Series is available in a single, dual and triple output for benchtop use.
-
Product
Power Monitoring Software
-
A digital tool that continuously tracks, analyzes, and manages a facility's electrical system in real-time.
-
Product
Outdoor Permanent Mounted Load Bank
-
Mosebach Manufacturing Company
Mosebach Pad Mounted Load bank is designed to be permanently mounted next to a generator for dedicated testing. Its unique design allows it to be one of the smallest on the market! This size enclosure will fit 50 kW, 75 kW or 100kW of testing ability. Also available in 300kW and larger load banks.
-
Product
CW Power Sensors
E-Series
-
Operates with the EPM, EPM-P and P-series power meters Wide dynamic range sensors (-70 to +20 dBm)Accurate CW average power measurements Wide frequency coverage from 10 MHz to 26.5 GHz (sensor dependent)Calibration factors stored in EEPROM
-
Product
Programmable DC Electronic Load
DL3000 Series
-
The DL3000 series is a cost-effective, economical programmable DC electronic load with a friendly human-machine interface and excellent performance specifications. It provides a variety of remote communication interfaces to meet diverse testing needs for design and testing. A wide range of solutions are available for a wide range of industries including automotive electronics, aerospace and fuel cells.
-
Product
Bending Beam Load Cell
EST-7
-
Technopark Automation & Control
The EST-7 is a Bending Beam Load Cell suitable for use on lower capacity weigh hoppers, filling machines, packaging machines and conveyor belt scales. This load cell is available in capacities from 10 kg to 200 kg.
-
Product
DIN-Rail Power Meter
EVA-P220
-
Providing power parameters ; V, I, P, Q, kWh, kVarh etc.DIN-Rail mounting with high accuracy measurementFlexible phase wire connection. 1P2W/1P3W/3P3W(1/2/3CT)/3P4W(1/3CT)Front display with buttons for on-site operationCO2 emission calculation
-
Product
Power Supply
VITA, VPX, VME, cPCI
-
PCI-Systems Inc. intelligent power supplies integrate a microcontroller (MCU) for a fully programmable and flexible solution. Intelligent power conversion allows configuration and reconfiguration for different applications. With intelligent power conversion, the power supply becomes a platform solution for many different applications. The power supply can easily be reprogrammed to support different operating limits and control inputs.
-
-
Product
On Load Tap Changer Analyzer
TAP4
-
The TAP-4 is the first instrument to use vibro-acoustic measurement to perform tests on On-Load Tap Changers (OLTC). The TAP-4 is a universal device, it adapts itself to any type of transformers: MR Reinhausen, ABB, Ferranti, Federal Pioneer and others.
-
Product
Power Supplies
CX Series
-
The CX-series has 120mm fan. It has a high quality silver-coated fan guard and cable-tube on main power cables for better cable routing and neatness. This power supply is also compatible with all leading processors. Chassis come in a black & silver color to best suit your preferences.
-
Product
Power Quality Testing
-
Weshine Electric Manufacturing Co., Ltd
Transformer K Factor, Power factors(PF)and displacement factors, Short-term voltage flicker, .Three phase unbalance (Current and Voltage), Waveform real-time display(4 channels voltage /4 channels current) True RMS values of voltages and currents
-
Product
Power Supplies
CM Series
-
The CM-300 is perfect for those with smaller computer cases – tiny in size, but huge in effectiveness with an anti-corrosive nickel plated chassis. Within this power supply is an 80mm silent cooling fan designed to cool at maximum efficiency with the lowest noise level. And to power your CPU, the CM-300 comes with an 8 pin Xeon connector ready in a tube-tide design to keep all your wires tidy. The CM-300 is the ideal combination of power efficiency in a sleek body kit.
-
Product
Power Supplies and Sources
DC Power Supplies
-
DC power supplies are commonly used in electronics design, battery charging, electrical vehicle, research labs and education sectors. UNI-T offers both programmable and non-programmable power supplies with features such as low ripple and noise, constant voltage/current, overload protection, and more.
-
Product
DC Load Banks
-
Power House Manufacturing, Inc.
DC load banks by Power House Manufacturing are offered in any voltage from 6 to 1,000 Volts DC.
-
Product
Power Products
-
It is ideal for alarm, access control, and CCTV applications requiring up to 1.5 Amps.
-
Product
Power Patchcords
-
Most VPC standard High Power, Mini Power, and Micro Power patchcords are available in 36" and 72" lengths. Please contact a Field Application Engineer about the availability of other lengths.
-
Product
Power Supply
-
Power supplies of various ratings for Air, Naval ground based and space applications are developed. Products are implemented in VPX, VME, cPCI and custom form factor designs.Most products qualified to requirements of MIL-STD-461C and MIL-STD-810D or the equivalent JSS 55555 are designed and manufactured. Airborne versions are designed to meet MIL-STD-704D. Specific design constraints are handled with respect to long time storage life and suitability for air cooled or conduction cooled applications. Designs suitable for high power supplies of various ratings for Air, Naval, Ground based and space applications are developed. Products are implemented in VPX, VME, cPCI and custom form factors designs.
-
Product
AC Power Sources
-
Chroma Systems Solutions, Inc.
AC Power Supplies designed to satisfy both automated test system and laboratory benchtop requirements.
-
Product
Digital Power
-
Digital power is one of the most important technologies available today to reduce power consumption and also manage the growing power complexity in modern electronic systems in information and communications technology markets.
-
Product
Power Management Platform
SPIDER
-
Our unique solution to speed-up and secure the design of energy efficient power management systems
-
Product
Static Load Cells (5 N to 300 kN)
2530 Series
-
The Instron 2530 Series static load cells are precision force transducers engineered for versatile use in tension, compression, cyclic, and reverse stress testing, delivering accurate measurements down to 1/500th of their capacity. Individually temperature-compensated and calibrated, they support automatic recognition and electronic calibration, and are built to international force-measurement standards (ASTM E4, ISO 7500-1 class 0.5, and JIS B7721, B7733). With overload protection (150 % of rating without damage, 300 % without mechanical failure), the 2530 family offers consistent, repeatable performance across a wide force range (5 N to 300 kN).2530 Series load cells with capacities of 5 N to 100 N are for use with 3300, 3400, 5900, and 6800 Series testing systems.2530 Series Load cells with capacities of 500 N to 300 kN are for use with 3300 and 3400 Series testing systems.
-
Product
Power Supplies
NW-450B
-
Experience our new NW-series of power supplies. The NW-series can power your system from 450 to 650 watts. It offers a cooling system with a fan size of 120mm with automatic settings, so you no longer have to worry about high or low settings and if your fan is spinning too slow or too fast. The NW-series will adjust itself according to the necessary heat dissipation level. It is dual PCI-E ready for better graphics capabilities (at 650W). Painted in black, the NW series works and looks great.
-
Product
Artificial Power Network
KH3765
-
Beijing KeHuan Century EMC Technology Co,.LTD
The KH3765 artificial power supply network is equipped with the receiver produced by our company to conduct large current conduction interference test. The frequency range of this product is 150KHz-30MHz , the current is 50A , and the AC frequency can reach 0-400Hz . It is widely used and convenient to switch. Compared with similar products on the market, it greatly reduces the operation steps and buys valuable time for your rectification work. This product also provides a standard10AThe interface makes your test more convenient. Meet the requirements of GB-6113 for power supply network.
-
Product
Bench Power Supply
E3620 Series
-
This affordable triple-output supply offers stable and reliable power plus essential features for manual testing.
-
Product
Optical Power Meter
HOPM-3214
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Our designs series optical power meter to meet the high demand . It intergrades the handheld optical power meter and the intelligent optical power meter in one unit. It can be used for the absolute power measurement and relative measurement of the link loss in dB.
-
Product
*High Power Laser Beam Dumps & Low Power Beam Traps
-
Laser beam dumps for high power laser processing, laser measurement and other applications, and low power beam traps
